NANLITE FS-200B (01) PDF Document

The main components of the NANLITE FS-200B and their functions are as follows:

1. Lock catch: For installing and disassembling the reflector and other accessories.

2. Umbrella hole: For installing/removing an umbrella.

3. Reflector: For gathering light to improve central illumination.

4. Angle fixing knob: Allows for adjusting and fixing the illumination direction.

5. LCD screen: For displaying data.

6. Lamp body handle: Convenient for users to lift the lamp and adjust the direction of the light.

7. USB port: For updating the firmware.

8. Right knob: For selecting options and adjusting the color temperature under CCT mode.

9. MODE button: For switching between CCT mode, EFFECT mode, and MENU.

10. Power switch: For switching on/off the fixture.

11. Fuse base: For placing the fuse.

12. Left knob: For adjusting the DIM (dimming) and scrolling through different selections.

13. Power socket: AC power input socket.

14. Yoke: Designed for connecting the lamp to a light stand and adjusting the direction of light.

15. Bracket fixing knob: For locking the light fixture and stand, and adjusting the horizontal direction of light.

To install the reflector:

1. Ensure the reflector’s mounting points align with the slots on the light fixture.

2. When the mounting points and slots are aligned, push the reflector in place.

3. Rotate it in the direction shown on the light until it clicks into place.

To remove the reflector:

1. Press and hold the lock catch.

2. Rotate the reflector until it is free to be removed from the fixture.

1. Loosen the angle fixing knob.

2. Put the umbrella into the umbrella hole.

3. Tighten the angle fixing knob to lock the umbrella in place.

The NANLITE FS-200B supports 2.4G wireless protocol V1.0 and V2.0. To set the protocol:

1. Press the MODE button to enter the menu.

2. Rotate the “right knob” until “WIRELESS PR” is highlighted.

3. Rotate the “left knob” to select either V1.0 or V2.0.

Note: The fixture should be set to V2.0 when using a WS-RC-C1 or WS-RC-C2 remote controller, and set to V1.0 when using other remote controllers.

1. First, ensure the power switch of the fixture is off. Connect the power cable.

2. Turn on the light. The LCD screen will display the relevant information.

3. Press the MODE button until the screen shows CCT mode.

4. To adjust the brightness (DIM), rotate the “left knob”. The DIM range is from 000% to 100%.

5. To adjust the color temperature (CCT), rotate the “right knob”. The CCT range is from 2700K to 6500K.

When the fixture function is unlocked, in any mode, press the “left knob” to turn off the light. The brightness percentage on the screen will show 000%. Press the “left knob” again to restore the light to its previous state. You can press continuously to switch between on and off.

The NANLITE FS-200B has built-in effects including CCT LOOP, INT LOOP, FLASH, PULSE, STORM, TV, PAPARAZZI, CANDLE/FIRE, BAD BULB, FIREWORK, EXPLOSION and WELDING.

To access and select an effect:

1. Press the MODE button to switch to EFFECT mode.

2. Rotate the “right knob” to cycle through the available effects (FX).

3. Rotate the “left knob” to select the desired effect.

After selecting an effect in EFFECT mode, you can adjust its parameters:

CCT LOOP: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 02S-30S). Rotate the “left knob” to adjust the value of the selected parameter.

INT LOOP: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 02S-30S). Rotate the “left knob” to adjust the value.

FLASH: Rotate the “right knob” to select from DIM, CCT, and INTERVALS (Range: 0.1S-10S). Rotate the “left knob” to adjust the value.

PULSE: Rotate the “right knob” to select from DIM, CCT, and PULSES/MIN (Range: 001-240). Rotate the “left knob” to adjust the value.

STORM: Rotate the “right knob” to select from DIM, CCT, and INTVL (Interval, Range: 1s-60s). Rotate the “left knob” to adjust the value.

TV: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 001-100). Rotate the “left knob” to adjust the value.

PAPARAZZI: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 001-100). Rotate the “left knob” to adjust the value.

CANDLE/FIRE: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 001-100). Rotate the “left knob” to adjust the value.

BAD BULB: Rotate the “right knob” to select from DIM, CCT, and SPD (Speed, Range: 001-100). Rotate the “left knob” to adjust the value.

FIREWORK: Rotate the “right knob” to select from DIM, CCT, SPD (Range: 001-100), and DECAY (Range: 001-100). Rotate the “left knob” to adjust the value.

EXPLOSION: Rotate the “right knob” to select from DIM, CCT, SPD (Range: 001-100), and DECAY (Range: 001-100). Rotate the “left knob” to adjust the value.

WELDING: Rotate the “right knob” to select from DIM, CCT, SPD (Range: 001-100), and PAUSE (ON/OFF). Rotate the “left knob” to adjust the value.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select from the various menu options: CH, OUTPUT MODE, BLUETOOTH, WIRELESS PROTOCOL, FAN, FIRMWARE UPDATE, LANGUAGE, and VERSION.

1. Press the MODE button to enter the MENU.

2. The CH (channel) setting is the first option. If not, rotate the “right knob” to select it.

3. Rotate the “left knob” to set the channel number (1-512).

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select OUTPUT MODE.

3. Rotate the “left knob” to select either MAX or CONSTANT.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select BT (Bluetooth).

3. Press the “right knob” to enter the bluetooth reset interface.

4. Rotate the “right knob” to select RESET.

5. Press the “right knob” to confirm the reset. It will return to the main menu after the bluetooth reset is complete.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select FAN.

3. Rotate the “left knob” to select ON or OFF.

Note on limitations:

When the fan is turned ON, the maximum output of the light will be 100%.

When the fan is turned OFF, the maximum output of the FS-200B is 15%.

1. Insert a USB flash drive with the latest firmware into the fixture’s USB port.

2. Press the MODE button to enter the MENU.

3. Rotate the “right knob” to select FW UPDATE.

4. Press the “right knob” to enter the firmware update interface. The screen will show “FOUND FIRMWARE” with the version number.

5. Rotate the “right knob” to select UPDATE.

6. Press the “right knob” to confirm the update. The screen will show “FIRMWARE UPDATED” after the update is completed.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select LANGUAGE.

3. Rotate the “left knob” to select your desired language.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select VERSION.

3. The screen will display the current firmware version.

To lock all functions, long press the “right knob”. A lock icon will appear on the screen, and the current status cannot be changed by rotating the knobs.

To unlock the controls, long press the “right knob” again to release the lock status.

1. After opening the package, check for possible damage caused in transit. Do not use if damage is found and contact the distributor or manufacturer.

2. Do not use a power cable with damaged insulation. Do not unplug too hard or drag the power cable directly.

3. Ensure the voltage of the power supply accords with the voltage specified on the fixture before installation.

4. Turn the fixture off when it is not in use or before cleaning.

5. Keep the fixture safely stored and away from children.

1. Please remove the COB protective cap before using the fixture.

2. Please do not look directly at the emitter when the fixture is on.

3. Please wait for 10 seconds before turning off the fixture if parameter settings are done, in order to save the settings.

4. Please do not place any object on the fixture or allow liquid to flow inside the fixture.

5. Please do not place the fixture near any flammable or volatile substances like alcohol or gasoline.

6. Please do not use strong detergent for cleaning. Wipe off dirt by using a cloth with neutral cleanser.

7. Please set up the fixture in a dry and well-ventilated place. Do not use it in any humid, dusty or overheated environment. Ensure the fan and vent are unimpeded.

8. Do not disassemble the fixture to repair it yourself. Qualified professionals should conduct maintenance.

9. Do not cover the vents when using, as this can affect heat dissipation and result in damage. Be aware of anti-scald precautions when using the fixture for a long time, as the surface temperature can become high.

Light Fixture x 1

Power Cable 4.5M x 1

Reflector x 1

COB Protective Cap x 1

User Manual x 1

1. Please check whether the power cable and outlet connection are properly connected or loose.

2. Please check whether the voltage value is within the specified parameters.

If the failure is not resolved, please contact the place of purchase or manufacturer.

This indicates the control board may be damaged or the connecting cables of the control board have fallen off. Please contact the place of purchase or manufacturer for assistance.

There are a few potential reasons:

1. Please check whether the DIM is set to zero.

2. The LED board or main board may be damaged.

3. Please check whether the connecting cable of the LED board has fallen off.

If the failure is not resolved, please contact the place of purchase or manufacturer.

1. Check if there is any high-temperature object nearby that is making the operational environment temperature too high.

2. Check if the fixture is in any special effect mode, as some effects are designed to flicker.

If the failure is not resolved, please contact the place of purchase or manufacturer.

If the LCD screen displays “The fixture is overheated, please check the fixture!” it means the fan is damaged. In this case, please contact the place of purchase or the manufacturer for assistance.