Free English MUSICAL FIDELITY X-A200 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MUSICAL FIDELITY X-A200 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the technical specifications of the MUSICAL FIDELITY X-A200?
| Feature | Specification |
|---|---|
| Output power | 200 Watts RMS into 8 Ohms |
| THD | < 0.09% 20Hz-20kHz unweighted < 0.01% 20Hz-20kHz ‘A’ weighted < 0.003% 20Hz-20kHz @ 1W unweighted |
| Frequency response | 10Hz-50kHz ± 0.5dB 5Hz-80kHz ± 1dB |
| S/N ratio | > 107 dB unweighted > 120 dB ‘A’ weighted |
| Power consumption | 400W |
| Power requirements | 100/115/230V 50/60Hz AC (factory preset for country) |
| Dimensions (mm) | 170 x 175 x 430 approx. (W x H x D) Width and height include feet, depth includes terminals |
What installation precautions should be observed for the MUSICAL FIDELITY X-A200?
Your MUSICAL FIDELITY X-A200 is designed and built to provide trouble-free performance, but it is necessary to observe the following precautions:
Do not use the MUSICAL FIDELITY X-A200 near water.
Keep the MUSICAL FIDELITY X-A200 away from heat sources such as radiators.
Place all connecting cables where they are not likely to be walked on or trapped by items placed on them.
How do I connect audio sources and speakers to the MUSICAL FIDELITY X-A200?
All connections should be made before the mains lead is plugged in and the unit switched on.
The MUSICAL FIDELITY X-A200 can be used with a preamplifier or any line level source which has a volume control. Connect your pre-amp or other line level source to the phono input on the back panel marked “Line Input”.
Connect your loudspeaker to the loudspeaker terminals situated on the back panel marked “Loudspeaker Output”.
Once these connections are made, plug in the IEC type mains lead and switch on the unit.
How do I set up the MUSICAL FIDELITY X-A200 for bi-amping?
The MUSICAL FIDELITY X-A200 has a “Loop Out” facility to allow for easy bi-amping of speakers with bi-wireable crossovers. In this setup, typically one unit drives the tweeter (high frequencies) and one drives the woofer (low frequencies) of each loudspeaker enclosure, requiring four units for a stereo pair.
Taking the left channel connections first, connect the pre-amp’s (or other source’s) left output to the first MUSICAL FIDELITY X-A200’s line input.
Then, connect that unit’s loop output to the second MUSICAL FIDELITY X-A200’s line input. Both units will now be driven from the same left channel signal.
The first unit can now be used to drive the woofer and the second to drive the tweeter of the left channel loudspeaker.
Repeat this process for the right channel.
Does the MUSICAL FIDELITY X-A200 require maintenance or internal adjustments?
Do not remove any covers, as the MUSICAL FIDELITY X-A200 will not be covered under warranty if it has been tampered with. There are no adjustments within.
How does Radio Frequency Interference (R.F.I.) affect the MUSICAL FIDELITY X-A200?
This product has been tested to ensure that its operation will not be adversely affected by normal background levels of R.F.I. However, if the unit is subjected to abnormally high levels of R.F.I., it is possible that the unit may not perform as expected.
CLICK HERE TO DOWNLOAD MUSICAL FIDELITY X-A200 (01) PDF DOCUMENT