Free English TOTO WASHLET TCF796CG (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD TOTO WASHLET TCF796CG (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I insert or replace the batteries in the remote control for the TOTO WASHLET TCF796CG?
To insert the batteries:
1. Remove the remote control from the hanger.
2. Open the battery cover and insert two AA batteries.
3. Ensure the plus and minus signs are correct. When batteries are properly loaded, all LEDs on the remote control will light up for about 2 seconds.
4. Mount the remote control back in the hanger.
Use dry cell, alkaline batteries. Do not reuse old hose sets. If the remote control is secured to prevent theft, remove the screw from the remote control fixture before removing it from the hanger.
How do I turn on the power and open the water supply for the TOTO WASHLET TCF796CG?
1. Switch the breaker on the distribution board to ON. The wand will extend and then retract.
2. Check that the “Power” LED on the main display lights up.
3. Fully open the shutoff valve.
If the “Power” LED is off, remove the cover on the left side of the main unit and flip the power switch to ON. If the light is off but the power switch is ON, switch “Power” to “ON” using the remote control (press “Power ON/OFF” for about 3 seconds).
How do I use the basic cleansing functions on the TOTO WASHLET TCF796CG?
Sit on the toilet seat (the seat switch must be activated). Use the following buttons on the remote control:
Rear cleansing: Cleanses your rear.
Rear soft cleansing: Cleanses your rear with mild water pressure.
Front cleansing: Serves as a bidet for ladies.
Stopping: Stops the operation.
Functions that operate while a cleansing button is pressed:
Oscillating cleansing: The wand moves back and forth to cleanse thoroughly.
Pulsating cleansing: Cleanses with water pressure pulsating between soft and strong.
Wand position adjustment: Adjust the washing position to 5 different points between the front and the rear using the arrow buttons.
Water pressure adjustment: Adjust pressure to one of five levels using the [+] (Stronger) and [-] (Softer) buttons.
How do I use the Personal Setting Lock on the TOTO WASHLET TCF796CG?
You can store your preferred Wand position, Water pressure, and Warm water temperature settings.
To store settings: While cleansing is in progress, set your preferred preferences. Press and hold one of the user buttons (User 1 or User 2 symbol) for 2 seconds or longer.
To use stored settings: Press the desired user button (User 1 or User 2), and then press the button for the cleansing you want to use. The wand position and water pressure lamps will light up for about 10 seconds in their set positions, and the temperature display will switch.
How do I adjust the toilet seat and warm water temperature on the TOTO WASHLET TCF796CG?
Three different temperature levels (High, Medium, Low) and an “OFF” setting can be made.
1. Choose and press the button of the temperature you want to set: either the “Toilet seat temperature” button or the “Warm water temperature” button.
2. The current temperature level will appear.
3. Press the selected button repeatedly until the desired temperature level lights up (Low, Medium, High, or OFF).
If the button is not pressed for about 10 seconds, the LED will go off, but the setting is retained. To prevent condensation, the water temperature does not drop below 20°C even when set to “OFF”.
What are the Energy Saver features available on the TOTO WASHLET TCF796CG?
Auto energy saver: The product detects time periods with infrequent use and lowers the toilet seat temperature automatically (takes about 10 days to detect).
Auto energy saver+: In addition to the “Auto energy saver” feature, it automatically turns off the toilet seat heater during time periods when the toilet is never used.
Timer energy saver: You want to save energy only for a preset duration of time (6 hours or 9 hours). Once set, the toilet seat heater turns off automatically during the set time period every day.
You can also use Timer energy saver in combination with Auto energy saver or Auto energy saver+.
How do I set the Energy Saver features on the TOTO WASHLET TCF796CG?
Use the buttons on the back of the remote control:
Auto energy saver: Press the “Auto energy saver” button. The setting changes each time the button is pressed (Lit Green for ON, OFF for OFF).
Auto energy saver+: Press the “Auto energy saver+” button. The setting changes each time the button is pressed (Lit Green for ON, OFF for OFF).
Timer energy saver: Press the “Timer energy saver” button at the time you want the saver to start. Press repeatedly to select “6 hours”, “9 hours”, or “OFF”.
When energy saver is set, the “Energy saver” LED (green) on the main unit lights up.
How do I perform maintenance on the Main Unit of the TOTO WASHLET TCF796CG?
For safety, flip the power switch to OFF before maintenance.
1. Remove the cover on the left side of the main unit and flip the power switch to “OFF”.
2. Wipe with a soft cloth soaked in water and wrung out thoroughly. For heavy dirt, use diluted neutral kitchen detergent, then wipe with a soft cloth soaked in water.
3. Flip the power switch to ON.
4. Reinstall the cover.
Do not use dry cloth or toilet paper on plastic parts. Do not use toilet cleaner, household cleaner, benzene, paint thinner, powdered cleanser, or nylon scrubbing brushes.
How do I clean the Wand on the TOTO WASHLET TCF796CG?
1. Extend the wand. Press the “Wand cleaning” button on the back of the remote. (Or from the front: Press “Stopping” until LEDs flash, then press “Front cleansing” for 3 seconds).
2. Wipe with a soft, wet cloth. Do not pull, push, or press the wand with excessive force.
3. Press the “Stopping” button on the front side of the remote control to retract the wand.
How do I clean the Deodorizing Filter on the TOTO WASHLET TCF796CG?
Perform this approximately once a month:
1. Remove the cover on the left side of the main unit and flip the power switch to “OFF”.
2. Remove the deodorizing filter by holding the knob and pulling outward. Do not pull with undue force.
3. Clean with a tool such as a toothbrush. If washing with water, dry off all water before mounting.
4. Mount the deodorizing filter. Push firmly until a click sound is heard.
5. Flip the power switch to ON and reinstall the cover.
How do I clean or replace the Spray Nozzle on the TOTO WASHLET TCF796CG?
1. Extend the wand using the “Wand cleaning” button.
2. While holding the wand with a hand, press on both sides of the spray nozzle and slide it off. Do not pull with undue force.
3. To clean: Immerse in general lime scale remover (liquid). Do not disassemble.
4. To replace: Hold the wand and slide the replacement spray nozzle along the guide and push it in until a click sound is heard. Ensure the black gasket is attached.
5. Press the “Stopping” button to retract the wand.
How do I clean the Water Filter Drain Valve on the TOTO WASHLET TCF796CG?
Clean approximately once every 6 months if water pressure is weak:
1. Close the shutoff valve.
2. Extend the wand (Wand cleaning button) then press “Stopping” to retract it. This releases pressure from the water supply pipe.
3. Remove the cover on the left side of the main unit and flip the power switch to “OFF”.
4. Remove the two water filter drain valves. Loosen with a flat-head screwdriver and pull.
5. Clean the filter with a toothbrush. Remove dust from inside the hole.
6. Reinstall the valves and tighten securely with a screwdriver.
7. Flip power switch to ON, reinstall cover, and open the shutoff valve.
Caution: Do not remove the water filter drain valve while the shutoff valve is open.
How do I change the operational settings (Pre-mist, Deodorizer, Auto power deodorizer, Beep sound) on the TOTO WASHLET TCF796CG?
First, enter the setting mode by pressing the “Stopping” button on the front of the remote for about 10 seconds until all LEDs start flashing.
Once LEDs are flashing, use the following combinations to change settings:
Pre-mist: Press “Setting confirmation” and “Auto energy saver” buttons at the same time. (Short beep = Spray, Long beep = Do not spray).
Deodorizer: Press “Wand cleaning” button for 5 seconds or longer. (Short beep = ON, Long beep = OFF).
Auto power deodorizer: Press “Toilet seat temperature” button. (Short beep = ON, Long beep = OFF).
Beep sound: Press “Rear cleansing” button. (Short beep = On, Long beep = Off).
Personal setting lock: Press “Personal setting lock 2” button for 5 seconds or longer. Check by “Water pressure” LED.
After changing settings, press the “Stopping” button to complete.
What should I do if the water does not flow due to a water service interruption on the TOTO WASHLET TCF796CG?
1. Use a bucket to flush water. Pour strongly, aiming at the center of the bowl unit.
2. If the water level is low after flushing, add more water to prevent odors.
When water supply is restored, be sure to perform a flush to prevent waste from remaining in the drain pipe.
How do I prevent freeze damage to the TOTO WASHLET TCF796CG?
When the ambient temperature is likely to drop to 0°C or lower:
1. Close the shutoff valve.
2. Extend the wand to release pressure, then press “Stopping” to retract it.
3. Remove the cover on the left side of the main unit and flip the power switch to “OFF”.
4. Remove the two water filter drain valves using a flat-head screwdriver.
5. Reinstall the water filter drain valves and tighten securely.
6. Flip the power switch to ON and reinstall the cover.
7. Set the toilet seat temperature to “High”. Close the toilet seat and lid.
Do not use the energy saver feature during freezing conditions.
How do I drain the water for long periods of disuse on the TOTO WASHLET TCF796CG?
1. Close the shutoff valve.
2. Extend the wand to release pressure, then press “Stopping” to retract it.
3. Remove the cover on the left side and flip the power switch to “OFF”.
4. Remove the two water filter drain valves.
5. Reinstall the valves securely.
6. Reinstall the cover.
7. Pull out the water drain lever (water comes out from around the wand for about 20 seconds).
8. Release the hand to return the water drain lever to its original position.
How do I resupply water to the TOTO WASHLET TCF796CG after draining it?
1. Open the shutoff valve. Check for leaks.
2. If power is not on, remove cover and flip power switch to “ON”. Reinstall cover.
3. Discharge water from the wand: Press down on the left side of the toilet seat, press “Rear cleansing” to discharge water (catch in a cup), then press “Stopping”.
Troubleshooting: What should I check if the wand does not extend or cleansing water does not come out on the TOTO WASHLET TCF796CG?
Check the following:
1. Did you sit on the toilet continuously for 2 hours or longer? Stand up and sit again.
2. Is the seat switch activated? Sit back properly on the seat.
3. Is the shutoff valve closed? Fully open it.
4. Is the wand or filter clogged? Clean the nozzle and filter.
5. Is the water pressure set to a low level?
6. If water supply pressure dropped significantly, flip power switch OFF, wait 10 seconds, then ON.
Troubleshooting: Why is the toilet seat cold on the TOTO WASHLET TCF796CG?
1. Is the toilet seat temperature set to “OFF” or a low level?
2. Is energy saver in operation? If the “Energy saver” LED is on and “Power” LED is off, the seat heater is temporarily off or reduced. It warms up in about 15 minutes after sitting.
3. Have you been seated for a long time? After 20 minutes, temperature drops; after 1 hour, heater turns off. Stand up and sit again.
4. Is a seat cover installed? Remove it as it may block the seat switch.
Troubleshooting: What should I do if the Energy Saver LED does not light up on the TOTO WASHLET TCF796CG?
Did you flip the power switch to OFF or was there a power outage? The “Energy saver” LED may go off when power is turned on even if the feature is “ON”. It will turn on within about 24 hours since the setting is retained.
CLICK HERE TO DOWNLOAD TOTO WASHLET TCF796CG (01) PDF DOCUMENT