MPAYEL 8002-WHITE (01) PDF Document

1. To reduce the risk of electric shock, turn off the electricity to the fan at the main fuse box or circuit panel before beginning.

2. All wiring must be in accordance with the local electrical codes or National Electrical Code. Electrical installation should be performed by a qualified licensed electrician.

3. To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.

4. Make sure the installation site you choose allows clear space for the blades to rotate and at least seven 7 feet (2.13 meters) of clearance between the floor and the fan blade tips. The fan should be mounted so that the tips of the blades are at least 18 inches (45.72 centimeters) from walls or other upright structures.

5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

6. The outlet box and ceiling support structure must be securely mounted and capable of supporting at least 45 KGs.

7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.

8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.

9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.

10. Electrical diagrams are for reference only.

11. The fan is suitable for indoor use only.

Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Tools required for assembly (not included):

• Electrical tape

• Phillips screwdriver

• Plier

• Safety glasses

• Step ladder

• Wire strippers

Helpful tools (not included):

• DC tester light

• Tape measure

• Wiring handbook

• Wire cutters

Check to see that you have received the following parts:

1. Screws (for wood ceiling)

2. Expansion Screws

3. Safety Rope

4. Hanging Plate

5. Ceiling Fan Body

6. Hand-Held Remote

7. ABS Blades (x3)

8. Light Cover

Wiring outlet box and box connectors must be of the type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following size:

Follow these steps for the ground assembly procedure:

1. Twist the light cover counterclockwise and take it down.

2. Pull out the socket of the light strip.

3. Twist out the screw that locks the round hole in the disc. Loosen the remaining two screws.

4. Twist the disc clockwise and take it down.

5. Fix the three fan blades in turn with screws.

6. Align the disc with the screw and snap it in, and tighten the screw.

7. Connect the light strip socket.

8. Rotate the shade clockwise to secure.

WARNING: Failure to disconnect the power supply prior to installation may result in serious injury or death.

To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7 feet (2.13 meters) from the floor and 18 inches (45.72 centimeters) from any wall or obstruction.

If there isn’t an existing CUL listed mounting box, then read the following instructions:

For a concrete ceiling:

Mark the location, then drill two holes in the ceiling to aid in securing the ceiling bracket with two expansion screws provided. Secure the mounting bracket to the building structure with the two expansion screws provided and tighten the screws.

For a wood ceiling:

Mark the location for the ceiling fan first. Secure the mounting bracket to the building structure with four screws provided. Add a spacer to each screw.

WARNING:

To reduce the risk of fire, electrical shock, or personal injury, mount the fan to an outlet box marked acceptable for fan support of 15.88kg (35 lbs) or less. Use screws supplied with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage to the ceiling fan’s remote control unit.

1. Carefully lift the fan to the hook on the hanging plate to ensure it is safely attached.

2. Connect the ceiling fan wire (fire wire with fire wire, zero wire with zero wire) reserved with the ceiling plate.

3. Follow the wiring diagram provided in the user manual for all connections, including the controller, motor input, LED input, and power lines.

4. Connect the Product motor input male terminal plug to the Controller output female terminal plug.

5. Connect the Product Led input male terminal plug to the Led output female terminal plug.

6. Connect the house wiring to the three-position terminal: the neutral line to the controller’s neutral input, the live line (Power Cord) to the controller’s live line input, and the ground wire (yellow-green).

Note: Do not connect the wires to the Antenna.

1. To make the fan operational, install AAA/1.5V batteries in the hand-held remote. Store the remote away from excessive heat or humidity.

2. To pair the remote with the fan (Remote Code Matching), long press the “SET UP” button within 5 seconds of when the light is turned on. If it beeps 2 times, the code is successfully matched.

3. The remote can also be paired with an app for smart control. Scan the QR code in the manual to download the APP and register an account. After adding the device in the app, click the device icon, cut off power to the fan for 1-2 seconds, then power it on. Click the “Pairing” button in the app. If it beeps 2 times, the pairing is successful.

ON/OFF: Light ON/OFF

ALL OFF: ALL OFF

K: Color Temperature Switch

*: Small Night Light

Brightness +: Click or long press this button to enhance the brightness

Brightness -: Click or long press this button to weaken the brightness

Color Temp +: Long press this button to increase color temperature

Color Temp -: Long press this button to decrease color temperature

F/R: Fan rotates forward / Fan rotates in reverse

2H: Turn off automatically after 2-hour countdown

123456: Fan speed, 1 is the weakest, 6 is the strongest

Nature Wind Icon: Nature wind

FAN OFF: Fan OFF

If airflow is desired in the opposite direction, directly tap the F/R button on the remote and the fan will stop then rotate in the opposite direction.

For your own safety, turn off power at the fuse box or circuit breaker before troubleshooting.

Probable Causes:

• Fuse or circuit breaker blown.

• Loose power line connections to the fan, or loose switch wire connections in the switch housing.

• Dead battery in remote control.

• Reversing switch in neutral position.

Suggested Remedies:

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in the switch housings. CAUTION: Make sure main power is turned off!

3. Replace with a new battery.

4. Make sure reversing switch position is all the way to one side.

For your own safety, turn off power at the fuse box or circuit breaker before troubleshooting.

Probable Causes:

• Loose screws in motor housing.

• Wire connectors inside housing rattling.

• Motor noise caused by solid state variable speed control.

Suggested Remedies:

1. Check to make sure all screws in motor housing are snug (do not overtighten).

2. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. CAUTION: Make sure main power is turned off!

3. Some fan motors are sensitive to signals from solid-state variable speed controls. Solid-state controls are not recommended; choose an alternative control method.

For your own safety, turn off power at the fuse box or circuit breaker before troubleshooting.

Probable Causes:

• Setscrew in downrod support is loose.

• Setscrew in downrod/hanger ball assembly is loose.

• Hanger bracket and/or ceiling outlet box is not securely fastened.

Suggested Remedies:

1. Tighten both setscrews securely in downrod support.

2. Tighten the setscrew in the hanging plate assembly.

3. Tighten the hanger bracket screws to the outlet box, and secure the outlet box.

Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint-free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to the finish.

CAUTION: Do not use water when cleaning your ceiling fan. It could damage the motor or the finish and create the possibility of electrical shock.