MONTPELLIER MFF183EXWD INOX (01) PDF DOCUMENT

Please read the user manual carefully.

Make sure that the appliance is left to stand for a minimum of 4 hours before being turned on for the first time.

Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction.

Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

Do not damage the refrigerant circuit.

When positioning the appliance, ensure the supply cord is not trapped or damaged.

Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.

In order to avoid any hazards resulting from the instability of the appliance, it must be fixed in accordance with the instructions.

If your appliance uses R600a as a refrigerant, you should take care during transportation and installation to prevent the cooler elements from being damaged. R600a is an environmentally friendly and natural gas, but it is explosive. In the event of a leak due to damage of the cooler elements, move your fridge away from open flames or heat sources and ventilate the room where the appliance is located for a few minutes.

While carrying and positioning the fridge, do not damage the cooler gas circuit.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

This appliance is intended to be used in household and domestic applications only.

If the socket does not match the refrigerator plug, it must be replaced by a service agent or similarly qualified persons in order to avoid a hazard.

A specially grounded plug has been connected to the power cable of your refrigerator. This plug should be used with a specially grounded socket of 13 amperes. If there is no such socket in your house, please have one installed by an authorised electrician.

If the supply cord is damaged, it must be replaced by an authorised service agent or similar qualified persons, in order to avoid a hazard.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances. Children are not expected to perform cleaning or user maintenance of the appliance, very young children (0-3 years old) are not expected to use appliances, young children (3-8 years old) are not expected to use appliances safely unless continuous supervision is given, older children (8-14 years old) and vulnerable people can use appliances safely after they have been given appropriate supervision or instruction concerning use of the appliance. Very vulnerable people are not expected to use appliances safely unless continuous supervision is given.

To avoid contamination of food, please follow these instructions:

Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.

Clean regularly surfaces that can come in contact with food and accessible drainage systems.

Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.

If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.

For the water dispenser: Clean water tanks if they have not been used for 48h; flush the water system connected to a water supply if water has not been drawn for 5 days.

Before using your fridge freezer for the first time, please pay attention to the following points:

The operating voltage for your fridge freezer is 220-240 V at 50Hz.

The plug must be accessible after installation.

Your fridge freezer may have an odour when it is operated for the first time. This is normal and the odour will fade when your fridge freezer starts to cool.

Before connecting your fridge freezer, ensure that the information on the data plate (voltage and connected load) matches that of the mains electricity supply. If in doubt, consult a qualified electrician.

Insert the plug into a socket with an efficient ground connection. If the socket has no ground contact or the plug does not match, we recommend you consult a qualified electrician for assistance.

The appliance must be connected with a properly installed fused socket. The power supply (AC) and voltage at the operating point must match with the details on the name plate of the appliance.

We do not accept responsibility for any damages that occur due to ungrounded usage.

Place your fridge freezer where it will not be exposed to direct sunlight.

Your fridge freezer must never be used outdoors or exposed to rain.

Your appliance must be at least 50 cm away from stoves, gas ovens and heater cores, and at least 5cm away from electrical ovens.

If your fridge freezer is placed next to a deep freezer, there must be at least 2cm between them to prevent humidity forming on the outer surface.

Do not cover the body or top of fridge freezer with lace. This will affect the performance of your fridge freezer.

Clearance of at least 150 mm is required at the top of your appliance. Do not place anything on top of your appliance.

Do not place heavy items on the appliance.

Clean the appliance thoroughly before use (see Cleaning and Maintenance).

Before using your fridge freezer, wipe all parts with a solution of warm water and a teaspoon of sodium bicarbonate. Then, rinse with clean water and dry. Return all parts to the fridge freezer after cleaning.

Use the adjustable front legs to make sure your appliance is level and stable. You can adjust the legs by turning them in either direction. This must be done before placing food in the appliance.

Install the plastic distance guide (the parts on the black vanes – condenser – at the rear) by turning it 90° to prevent the condenser from touching the wall. The distance between the appliance and back wall must be a maximum of 75 mm.

Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a specially earthed plug.

Important: Do not use the appliance without the fuse cover in position. Should the fuse need to be replaced, it must be replaced with a 13A fuse, ASTA approved to BS1362.

The plug must be used with a specially earthed socket of 13 amperes. If there is no such socket in your house, please have one installed by an authorised electrician.

The mains lead of this appliance has been fitted with a BS 1363A 13A fused plug. To change a fuse in this type of plug, follow the steps below:

1. Remove the fuse cover and fuse.

2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.

3. Replace fuse cover.

While carrying and positioning the fridge, do not damage the cooler gas circuit.

Do not use damaged, torn or old plugs.

Do not pull, bend or damage the cord.

Do not use plug adapter.

This appliance is designed for use by adults. Do not allow children to play with the appliance or hang off the door.

Never touch the power cord/plug with wet hands. This may cause a short circuit or electric shock.

Do not place glass bottles or cans in the ice-making compartment as they will burst when the contents freeze.

Do not place explosive or flammable material in your fridge. Place drinks with high alcohol content vertically in the fridge compartment and make sure their tops are tightly closed.

When removing ice from the ice-making compartment, do not touch it. Ice may cause frost burns and/or cuts.

Do not touch frozen goods with wet hands. Do not eat ice-cream or ice cubes immediately after they are removed from the ice-making compartment.

Do not re-freeze thawed frozen food. This may cause health issues such as food poisoning.

Fresh Food Compartment (Fridge): Most efficient use of energy is ensured in the configuration with the drawers in the bottom part of the appliance, and shelves evenly distributed, position of door bins does not affect energy consumption.

Freezer Compartment (Freezer): Most Efficient use of energy is ensured in the configuration with the drawers and bins are on stock position.

Parts may vary according to the appliance model.

A. Refrigerator compartment

B. Freezer compartment

1. Thermostat Box

2. Refrigerator Shelves

3. Wine Rack

4. Crisper Cover

5. Crisper

6. Freezer Flap

7. Freezer Baskets

8. Door Balcony

9. Water Tank

10. Door Balcony (bottles)

11. Ice Cube Tray

12. Egg Holder

Front Reservoir Group:

1. Valve Lever

2. Drip Tray

Water Tank Group:

3. Water Tank Cover

4. Water Fill Cover

5. Water Tank Cover Latch

6. Water Tank

7. Tank Gasket

8. Tap Detail

Overall dimensions*

* The height, width and depth of the appliance without the handle

Space required in use*

* The height, width and depth of the appliance including the handle, plus the space necessary for free circulation of the cooling air.

Overall space required in use*

* The height, width and depth of the appliance including the handle, plus the space necessary for free circulation of the cooling air, plus the space necessary to allow door opening to the minimum angle permitting removal of all internal equipment.

Frost Free fridge freezers have a different operating system to static fridge freezers. In normal (static) freezers, humidity causes frost buildup. To defrost, you are required to periodically switch off the fridge, remove the food, and then remove the ice.

The situation is completely different in Frost Free freezers like the MONTPELLIER MFF183EXWD INOX. A built-in fan blows dry and cold air evenly throughout the freezer compartments. The cold air disperses uniformly, ensuring all your food is cooled equally, thus preventing humidity and frost build-up.

The thermostat automatically regulates the temperature inside the cooler and freezer compartments. Refrigerator temperatures can be obtained by rotating the dial to higher numbers; 1 to 3, Max or SF.

Important note: Do not try to rotate the dial beyond position 1, it may stop your appliance from working.

• 1 – 2: For short-term storage of food
• 3: For long-term storage of food
• Max: Maximum cooling position. The appliance will work longer. If required, change the temperature setting.

If device has SF position:

Turn the dial to SF to freeze fresh food quickly. In this position, the freezer compartment will operate at lower temperatures. After your food freezes, turn the thermostat dial to its normal use position. If you do not change the SF position, your appliance work will automatically return to its last used thermostat position according to the time indicated in the note. The super mode will be canceled automatically after a maximum of 48 hours.

Your appliance is designed to operate in the ambient temperature ranges stated in the standards, according to the climate class stated in the information label. It is not recommended that your fridge is operated in the environments which are outside of the stated temperature ranges. This will reduce the cooling efficiency of the appliance.

The ambient temperature, temperature of the freshly stored food and how often the door is opened affects the temperature in the refrigerator compartment. If required, change the temperature setting.

It is not recommended that you operate your fridge in environments colder than 10°C in terms of its efficiency.

When setting the thermostat, take into consideration how often the appliance doors are opened and closed, how much food is stored in the refrigerator, and the environment in which the refrigerator is located.

When the appliance is first switched on, allow it to run for 24 hours in order to reach operating temperature. During this time, do not open the door and do not keep a large quantity of food inside.

Unplug your appliance during a power cut to prevent damage to the compressor. Once power is restored, delay plugging in your appliance for 5 to 10 minutes. This will help prevent damage to the appliance’s components.

Important Installation Instructions: This appliance is designed to work in difficult climate conditions and is powered with ‘Freezer Shield’ technology which ensures that the frozen food in the freezer will not defrost even if the ambient temperature falls as low as -15 °C. So you may then install your appliance in an unheated room without having to worry about frozen food in the freezer being spoilt. When the ambient temperature returns to normal, you may continue using the appliance as usual.

T (tropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C.

ST (subtropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C.

N (temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C.

SN (extended temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 10 °C to 32 °C.

Ice Tray

Fill the ice tray with water and place in the freezer compartment.

After the water has completely frozen, you can twist the tray as shown in the manual to remove the ice cubes.

The Plastic Scraper

After some time, frost will build up in certain areas of the freezer. The frost accumulated in the freezer should be removed regularly. Use the plastic scraper provided, if necessary. Do not use sharp metal objects for this operation. They could puncture the refrigerator circuit and cause irreparable damage to the unit.

The freezer box allows food to be accessed more easily.

Removing the freezer box:

1. Pull the box out as far as possible.

2. Pull the front of the box up and out.

Carry out the opposite of this operation when refitting the sliding compartment. Always keep hold of the handle of the box while removing it.

Mounting the Water Tank

1. Place the Water Tank flush with the recess in the door.

2. Push it down to firmly secure it into the holder.

Filling the Water Tank

You can either fill using the Water Fill Cover (option 1) or by removing the top cover of the Water Tank to fill it (option 2).

Important: Do not use the Water Dispenser for anything except water. If you leave water in the tank for a long time, it will cause an odour. Clean the Water Tank before using it for the first time.

Cleaning the Water Tank

1. Lift the Water Tank.

2. Remove the tank cover by releasing the Water Tank Cover Latches.

3. Clean the tank with warm water and reassemble the pieces that you have removed.

Stowing the Water Tank

Install the Water Tank as shown. Make sure that the tap and the hole match each other while installing. Water flow may not be as expected if the tank has not been installed properly. Also check that the gaskets have been assembled properly.

Serving Water

The Drip Tray must be placed in position. Then gently press the Valve Lever while holding a glass in place to serve. Water may splash on serving when below the minimum level marked on the tank. Please hold the glass momentarily after serving to avoid drips. If the drip tray is full, it should be emptied to prevent overflowing.

For normal working conditions, it will be sufficient to adjust the temperature setting of your refrigerator to +4 °C.

The temperature of the fridge compartment should be in the range of 0-8 °C, fresh foods below 0 °C are iced and rotted, bacterial load increases above 8 °C, and spoils.

To reduce humidity and avoid the consequent formation of frost, always store liquids in sealed containers in the refrigerator.

Never place warm food in the refrigerator. Warm food should be allowed to cool at room temperature and should be arranged to ensure adequate air circulation.

Make sure no items are in direct contact with the rear wall of the appliance as frost will develop and packaging will stick to it. Do not open the refrigerator door frequently.

We recommend that meat and clean fish are loosely wrapped and stored on the glass shelf just above the vegetable bin where the air is cooler.

Store loose fruit and vegetable items in the crisper containers.

Storing fruit and vegetables separately helps prevent ethylene-sensitive vegetables (green leaves, broccoli, carrot, etc.) being affected by ethylene-releaser fruits (banana, peach, apricot, fig etc.).

Do not put wet vegetables into the refrigerator.

To avoid cross-contamination do not store meat products with fruit and vegetables. Water leaking from meat may contaminate other products.

Do not put food in front of the air flow passage.

Consume packaged foods before the recommended expiry date.

NOTE: Potatoes, onions and garlic should not be stored in the refrigerator.

The freezer is used for storing frozen food, freezing fresh food, and making ice cubes.

For freezing fresh food; wrap and seal fresh food properly, that is the packaging should be air tight and shouldn’t leak. Special freezer bags, aluminium foil polythene bags and plastic containers are ideal.

Do not store fresh food next to frozen food as it can thaw the frozen food.

Before freezing fresh food, divide it into portions that can be consumed in one sitting.

Consume thawed frozen food within a short period of time after defrosting.

Never place warm food in the freezer compartment as it will thaw the frozen food.

Always follow the manufacturer’s instructions on food packaging when storing frozen food. If no information is provided food, should not be stored for more than 3 months from the date of purchase.

When purchasing frozen food, make sure that it has been stored under appropriate conditions and that the packaging is not damaged.

Do not purchase frozen food if the packaging shows signs of humidity and abnormal swelling.

The storage life of frozen food depends on the room temperature, the thermostat setting, how often the door is opened, the type of food, and the length of time required to transport the product from the shop to your home. Always follow the instructions printed on the packaging and never exceed the maximum storage life indicated.

The maximum amount of fresh food (in Kg) that can be frozen in 24 hours is indicated on the appliance rating label.

To use the maximum capacity of the freezer compartment, use the glass shelves for the upper and middle section, and use the lower basket for the bottom section.

Use the fast freezing shelf (the bottom drawer) to freeze home cooking and other food more quickly.

Important note: Never refreeze thawed frozen food. The taste of some spices in cooked dishes changes over time. Add small amounts of spices to food to be frozen, or add after thawing. Suitable oils for freezing are margarine, calf fat, olive oil and butter. Unsuitable oils are peanut oil and pig fat.

NOTE: Thawed frozen meat should be cooked as fresh meat. If the meat is not cooked after defrosting, it must not be re-frozen.

Meat & Fish

Vegetables and Fruits

Bread, Pastry, etc.

Dairy Products

Disconnect the unit from the power supply before cleaning.

Do not wash your appliance by pouring water on it.

Do not use abrasive products, detergents or soaps for cleaning the appliance.

After washing, rinse with clean water and dry carefully. When you have finished cleaning, reconnect the plug to the mains supply with dry hands.

Make sure that no water enters the lamp housing and other electrical components.

The appliance should be cleaned regularly using a solution of bicarbonate of soda and lukewarm water.

Clean the accessories separately by hand with soap and water. Do not wash accessories in a dish washer.

Clean the condenser with a brush at least twice a year. This will help you to save on energy costs and increase productivity.

Defrosting the Refrigerator Compartment

Defrosting occurs automatically in the refrigerator compartment during operation. The water is collected by the evaporation tray and evaporates automatically. The evaporation tray and the water drain hole should be cleaned periodically with the defrost drain plug to prevent the water from collecting at the bottom of the refrigerator instead of flowing out. You can also clean the drain hole by pouring half a glass of water down it.

Freezer defrosting process

Your appliance performs automatic defrosting. The water formed as a result of defrosting passes through the water collection spout, flows into the water tray behind your appliance and evaporates there. Make sure you have disconnected the plug of your appliance before cleaning the water tray. Remove the water tray from its position by removing the screws (if it has screws). Clean it with soapy water at specific time intervals. This will prevent odours from forming.

The original packaging and foam may be kept for re-transportation (optional).

Fasten your appliance with thick packaging, bands or strong cords and follow the instructions for transportation on the packaging.

Remove all movable parts (shelves, accessories, vegetable bins, and so on) or fix them into the appliance against shocks using bands when re-positioning or transporting.

Always carry your appliance in the upright position.

If your refrigerator is not working properly, there may be a minor problem. Check the following:

The appliance does not operate check:

There is power.

The mains is connected.

The thermostat setting is on the “•” position.

The socket is defective. To check this, plug another working appliance into the same socket.

If the appliance performs poorly, check:

The appliance is overloaded.

The doors are closed properly.

There is any dust on the condenser.

There is enough space near the rear and side walls.

The following noises can be heard during normal operation of the appliance.

Cracking (ice cracking) noise occurs:

During automatic defrosting.

When the appliance is cooled or warmed (due to expansion of appliance material).

Clicking noise occurs:

When the thermostat switches the compressor on/off.

Motor noise:

Indicates the compressor is operating normally. The compressor may cause more noise for a short time when it is first activated.

Bubbling noise and splashing occurs:

Due to the flow of the refrigerant in the tubes of the system.

Water flowing noise occurs:

Due to water flowing to the evaporation container. This noise is normal during defrosting.

If the appliance is noisy:

The cooling gas which circulates in the refrigerator circuit may make a slight noise (bubbling sound) even when the compressor is not running. Do not worry, this is normal. If you hear a different sound, check whether:

The appliance is level.

Anything is touching the rear of the appliance.

Objects in the appliance are vibrating.

As this is a Wet Wall fridge, under normal operation, moisture within the fridge will freeze to the back wall forming ice during the cooling phase. Once the appliance has reached the required temperature it will enter its Auto-Defrost mode, which means the ice on the back wall will start to defrost and form water droplets that will then run down the rear wall and into the defrost channel.

Check that the drain hole for the water is not clogged (use a defrost drain plug to clean the drain hole if blocked). Make sure that nothing is touching the back wall as this will cause water to run on to shelves or bypass the drain hole. Also, if anything is touching the back wall it will freeze to the wall during the cooling phase.

Check if:

There is food or packaging preventing the door from closing.

The door joints are broken or torn.

Your appliance is on a level surface.

If the appliance is switched off or unplugged, wait at least 5 minutes before plugging the appliance in or restarting it in order to prevent damage to the compressor.

The cooling unit of your refrigerator is located at the rear of the appliance. Therefore, water droplets or ice may form on the rear surface of your fridge due to the operation of the compressor at specified intervals. This is normal, there is no need to perform a defrosting operation unless there is excessive ice.

If you do not intend to use your fridge for a long period of time (such as during the summer holidays), set the thermostat to “•” position, defrost and clean your fridge, leaving the door open to prevent the formation of mildew and odour.

If a problem persists after you have followed all the instructions, please consult the nearest authorised service centre.

1. Install the appliance in a cool, well ventilated room, but not in direct sunlight and not near a heat source (such as a radiator or oven) otherwise an insulating plate should be used.

2. Allow warm food and drinks to cool before placing them inside the appliance.

3. Place thawing food in the refrigerator compartment. The low temperature of the frozen food will help cool the refrigerator compartment while the food is thawing. This will save energy. Frozen food left to thaw outside of the appliance will result in a waste of energy.

4. Drinks or other liquids should be covered when inside the appliance. If left uncovered, the humidity inside the appliance will increase, therefore the appliance uses more energy. Keeping drinks and other liquids covered helps preserve their smell and taste.

5. Avoid keeping the doors open for long periods and entering the appliance which causes the compressor to switch on unnecessarily often.

6. Keep the covers of the different temperature compartments (such as the crisper and chiller) closed.

7. The door gasket must be clean and pliable. In case of wear, replace the gasket.

8. Energy consumption of your appliance is declared without drawers and fully loaded in the freezer compartment.

9. For saving energy, do not use volume between the load limit and the door, along the load limit line. Load limit line is also used in energy consumption declaration.