MITSUBISHI ELECTRIC MCCH1 (01) PDF DOCUMENT

The installation procedure for the MITSUBISHI ELECTRIC MCCH1 wireless accessories involves three main steps:

1. Install batteries in wireless devices.

2. Link devices to the wireless network.

3. Mount the outdoor sensor.

To install batteries in your MITSUBISHI ELECTRIC MCCH1 wireless accessories, make sure they are inserted properly according to the polarity marks:

Portable central controller: Install 3 fresh AA batteries.

Outdoor air sensor: Install 2 fresh AA lithium batteries.

To link devices to the wireless network, follow these steps at the wireless receiver:

1. Remove the cover from the wireless receiver.

2. Verify the POWER light is solid green.

3. Press and release the CONNECT button.

4. If the CONNECT light does not flash, another receiver or RedLINK wireless adapter may be in wireless setup mode. Exit the wireless setup at the other device.

Please note, the flashing status light will time out after 15 minutes of inactivity. Press the CONNECT button again if necessary.

1. Make sure the CONNECT light on the wireless receiver is flashing.

2. Press CONNECT on the MITSUBISHI ELECTRIC MCCH1 Portable Central Controller. There will be a short delay as the controller seeks a signal from the wireless network.

3. When the screen displays “Connected,” press DONE.

4. Press NO on the next screen (“CONNECT MORE?”) to save and exit. (Or press YES and repeat steps 1-4 to link another receiver.)

The linking procedure may time out if there is no keypress within 15 minutes. To begin again, press and hold the blank space (or arrow, if present) in the lower right corner of the screen until the display changes (about 3 seconds).

1. Make sure the CONNECT light on the wireless receiver is flashing.

2. Press and release the CONNECT button on the back of the sensor.

3. Check the remote controller to verify that the outdoor sensor is working. After about 15 seconds, the remote controller should display the outdoor temperature and humidity.

Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location that is protected from direct sunlight.

After securing the bracket to the wall, place the sensor securely in the bracket, with its back facing away from the wall.

If there is more than one Wireless Receiver, Equipment Interface Module (EIM), or zone panel, the wireless devices must be linked separately to each one.

If E1 or E appears on the screen, check the error code number on the right side of the screen for the following issues:

29: You are attempting to connect the MITSUBISHI ELECTRIC MCCH1 Portable Central Controller to an incompatible device.

34: Low signal strength. Move the MITSUBISHI ELECTRIC MCCH1 Portable Central Controller to a different location and try again.

38: Make sure the Connect light on the wireless receiver is flashing and that you are 2+ feet away from the wireless receiver.

To replace a MITSUBISHI ELECTRIC MCCH1 Portable Central Controller or an outdoor air sensor, install batteries in the new component and follow the procedures on pages 2-3 to link it to the wireless network.

After installing a new wireless receiver, Equipment Interface Module, or zone panel, you must re-set the MITSUBISHI ELECTRIC MCCH1 Portable Central Controller to communicate with the new equipment. At the controller:

1. Press and hold the blank space (or arrow if present) in the lower right corner of the screen until the display changes (about 3 seconds).

2. Press REMOVE, then press YES to disconnect from the old equipment.

3. Follow the procedure to link the controller to the new equipment.

1. To remove all wireless devices, press and hold the CONNECT button on the wireless receiver, Equipment Interface Module, or wireless adapter for 10 seconds.

2. To reconnect the devices, follow the standard linking procedure.

The MITSUBISHI ELECTRIC MCCH1 device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the MITSUBISHI ELECTRIC MCCH1 equipment.

If your MITSUBISHI ELECTRIC MCCH1 equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.