MAKITA BO4565 (01) PDF DOCUMENT

The specifications for the MAKITA BO4565 Finishing Sander are as follows:

Note:

Due to a continuing program of research and development, these specifications are subject to change without notice.

Specifications may differ from country to country.

Weight according to EPTA-Procedure 01/2014.

The MAKITA BO4565 Finishing Sander is intended for the sanding of large surfaces of wood, plastic, and metal materials, as well as painted surfaces.

The MAKITA BO4565 tool should be connected only to a power supply of the same voltage as indicated on the nameplate. It can only be operated on a single-phase AC supply. The tool is double-insulated and can, therefore, also be used from sockets without an earth wire.

Noise

The typical A-weighted noise level determined according to EN62841:

Sound pressure level (LPA): 81 dB (A)

Sound power level (LWA): 92 dB (A)

Uncertainty (K): 3 dB (A)

It is recommended to wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) determined according to EN62841:

Work mode: sanding metal plate

Vibration emission (ah): 4.0 m/s²

Uncertainty (K): 1.5 m/s²

NOTE: The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure.

WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

SANDER SAFETY WARNINGS

1. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses.

2. Hold the tool firmly.

3. Do not leave the tool running. Operate the tool only when hand-held.

4. This tool has not been waterproofed, so do not use water on the workpiece surface.

5. Ventilate your work area adequately when you perform sanding operations.

6. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

7. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection.

8. Be sure that there are no cracks or breakage on the pad before use. Cracks or breakage may cause a personal injury.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

CAUTION: Before plugging in the tool, always check to see that the tool is switched off.

To start the tool, press the “I” side of the switch. To stop the tool, press the “O” side of the switch.

CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

NOTE: Use Makita hook-and-loop sandpaper with this sander.

To attach the sandpaper:

1. Set the tool upside down so that the pad is on top.

2. Position the sandpaper to fit the shape of the base. Be sure to align the holes on the sandpaper with the holes on the pad (the dust will be sucked into these holes; it is therefore important to leave them open).

3. Press the paper firmly over the pad.

To remove the sandpaper:

1. Set the tool upside down so that the sandpaper is on top.

2. Grasping one corner of the sandpaper, peel it from the pad.

NOTE: If the sandpaper is in good condition, save it for further use.

When sanding in narrow, hard-to-reach areas (e.g., shutters, blinds, louvers), attach the cone-shaped abrasive papers to the end of the pad (bottom and top). To sand the end of thin materials, fold the abrasive paper and attach it to the side of the pad.

Dust bag (accessory)

The use of the dust bag makes sanding operations clean and dust collection easy. To attach the dust bag, fit the bag’s entry port onto the dust spout on the tool. Make sure that the hole in the bag’s entry port is just over the pimple-like protrusion on the dust spout. For the best results, empty the dust bag when it becomes approximately half full, tapping it lightly to remove as much dust as possible.

Installing paper dust bag (accessory)

1. Place the paper dust bag on the paper dust bag holder with its front side upward. Insert the front fixing cardboard of the paper dust bag into the groove of the paper dust bag holder.

2. Then press the upper part of the front fixing cardboard in the arrow direction to hook it onto the claws.

3. Insert the notch of the paper dust bag into the guide of the paper dust bag holder.

4. Then install the paper dust bag holder set on the tool.

CAUTION:

Never run the tool without the abrasive paper. You may seriously damage the pad.

Never force the tool. Excessive pressure may decrease the sanding efficiency, damage the abrasive paper and/or shorten tool life.

Hold the tool firmly. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. A finishing sander is generally used to remove only a small amount of material at a time. Since the quality of the surface is more important than the amount of stock removed, do not bear down on the tool. Keep the base flush with the workpiece at all times.

CAUTION:

Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.

Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

The following accessories are available:

Abrasive paper (without pre-punched holes)

Paper dust bag

Paper dust bag holder

Punch plate

Dust bag

NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.