LOREX C831CD (01) PDF Document

The package contents for the LOREX C831CD include:

4K Ultra HD Dome Security Camera

Mounting Kit*

BNC / Power Extension Cable*

Power Adapter**

A REGULATED UL/CSA APPROVED power supply is REQUIRED for use with this camera (included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

Point the camera where there is the least amount of obstructions (i.e., tree branches).

Install the camera where vandals cannot easily reach.

Secure cabling so that it is not exposed or easily cut.

This camera is rated for outdoor use. Installation in a sheltered location is recommended.

Read this guide carefully and keep it for future reference.

Follow all instructions for safe use of the product and handle with care.

Use the camera within given temperature, humidity and voltage levels noted in the camera’s specifications.

Do not disassemble the camera.

Do not point the camera directly towards the sun or a source of intense light.

Use only the supplied regulated power supply provided with the product. Use of a non-regulated, non-conforming power supply can damage the product and void the warranty.

Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.

The supplied cable is rated for surface and in-wall mounting only. Cables for floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.

The dimensions are:

3.9 in / 100 mm (width)

3.5 in / 90 mm (height)

3.9 in / 100 mm (depth)

This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.

For the smoothest possible 4K video streaming experience, connect your DVR to a Gigabit router (use available 1000Mbps / 1Gbps Ethernet port).

The cable extension options are:

The extension cable must be a single stretch of cable between the DVR and camera. You cannot connect multiple extension cables to each other.

For longer cable runs, it is recommended to connect the power adapter directly to the camera, rather than at the end of the extension cable.

Indicators that your cable run may be too long include:

Camera loses video when switching to night vision.

Video is permanently black & white (even during day time).

Video is unclear, soft, or distorted.

Test your camera prior to selecting a permanent mounting location by temporarily connecting the camera and cable to your DVR.

Before Installing the Camera:

Decide whether to run the cables through the wall / ceiling (drilling required) or along the wall / ceiling.

If you run the cables along the wall / ceiling, you must run the cable through the cable notch on the base. This will keep the camera base flush to the surface when mounted.

To install your camera:

Step 1. Rotate the camera base counterclockwise to separate it from the ball camera, adjustment ring, and dome cover.

Step 2. Use the included mounting template to mark and drill holes for the included mounting screws.

Step 3. Feed the cable through the camera base. If you are running the cables against a wall or ceiling, make sure to pass the cable through the cable notch as shown above.

Step 4. Connect the cables as shown in the section ‘Connecting the Camera’.

Step 5. Mount the camera base to the mounting surface using the included screws and drywall anchors (optional).

Step 6. Place the adjustment ring over the dome cover, then place both over the ball camera. Twist the adjustment ring clockwise halfway onto the camera base. Do not tighten all the way.

Step 7. Move the ball camera to the desired position. While holding the ball camera firmly in place, twist the adjustment ring the rest of the way to secure it to the camera base. Holding the camera prevents it from moving while securing the adjustment ring.

Step 8. Remove the vinyl film from the camera lens when your installation is complete.

Connect the male power head and the BNC connector to the camera.

Connect the BNC connector to a video input on your DVR.

Connect the female power head to the included power adapter.

The cameras are only compatible with certain Lorex HD DVRs. For the full list of compatible recorders, visit lorex.com/compatibility.

Ensure your TV or monitor is on the correct input channel. Common terms for input channels: INPUT, AV CHANNEL, LINE1, LINE2, AUX.

Ensure your DVR is properly connected to your TV or monitor.

Ensure connections are properly connected.

Ensure the camera power supply is plugged in.

Ensure your camera isn’t pointed directly at a source of light (e.g., sun or spot light).

Check the brightness settings of the DVR and monitor.

Move your camera to a different location.

Check the brightness and contrast settings of the DVR and monitor.

Night vision activates when light levels drop. The area may have too much light.

Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth.

Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’.

Remove the vinyl film from the camera lens when your installation is complete.

Night vision reflects when pointing a camera through a window. Move the camera to a different location.