LG MAGNIT LSAB012-U2 (01) PDF Document

The safety precautions are intended to prevent unexpected danger or harm. Always follow these guidelines:

WARNING: If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.

CAUTION: If you ignore the caution message, you may be slightly injured or the product may be damaged.

WARNING: This product is for Indoor Use Only.

WARNING

• Before using an AC cable, make sure it conforms to the national standards.

• Operate the display only from a power source (i.e. voltage) indicated in the product specification. Otherwise, the product can be damaged, fire can occur, or you may be electrocuted.

• Be sure to connect the AC cable to a grounded power disconnecting device.

• Insert the AC cable securely so that it does not come loose. Poor connection may cause a fire or electric shock.

• In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous.

• Be careful not to place heavy objects on or step on the AC cable. Do not bend or pull the AC cable with excessive force.

• Do not connect the AC cable to a power disconnecting device if it has been damaged by a sharp object.

• Do not insert a conductor (such as a metal chopstick) into the power disconnecting device while the AC cable is connected on the other side. Do not touch the AC cable directly after removing it from the power disconnecting device.

• If water or any foreign substance enters the product, disconnect the AC cable immediately and contact the service center.

• Keep the AC cable away from heating devices.

• Never disassemble, repair, or modify the AC cable.

• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

• For the power consumption to be zero, the AC cable must be disconnected.

CAUTION

• If there is dust on the AC cable or the power disconnecting device, wipe them clean.

• If there is moisture on the AC cable or the power disconnecting device, wipe them clean. Do not touch them if your hands are wet.

• Do not turn the product on or off by connecting or disconnecting the AC cable. Do not use the AC cable as a switch.

• Do not disconnect the AC cable while using the product.

WARNING

• Contact the service center before moving the product.

• Make sure the product is turned off, unplugged, and all cables have been removed before the product is moved.

• When moving the product, do not shock or cause an impact on the front panel.

• Use the correct number of people according to the weight of the product. (Under 25 kg (55.1 lbs) per person; use lifting equipment when exceeding 100 kg (220.4 lbs)).

• Do not hold it upside down while holding only the stand (for stand supported models only).

CAUTION

• Do not dispose of the product-packing box. Use it when moving by putting the product in the box to carry it.

WARNING

• Do not drop an object on or impact the product. Keep out of reach of children and do not place toys or objects near the product.

• Do not put heavy objects on, or hang from, the product.

• Install the product firmly fixed on a floor, wall, etc. to prepare against external impact.

• Prevent children from climbing or hanging on the product.

• Do not install it where there are heating devices such as electrical heaters or lighting equipment.

• Do not install this product on a wall if it could be exposed to oil or oil mist.

• Do not leave the AC cable, signal cables, etc. in a walking path.

• Install the product in a dry place, not near dust and water. Avoid high temperatures and humidity.

• Safely install the product in a place that can hold its weight.

• A readily accessible disconnect device shall be incorporated external to the equipment.

• Power docking should include no more than 7 units.

CAUTION

• Install the product where no Electromagnetic Interference occurs.

• If you install the product in a place that does not meet the recommended conditions, it may cause serious damage. Check with a service engineer before installing.

• Make sure the product is well ventilated by installing it at a distance of 30 mm (1.1 inches) or more from the wall.

• When the AC cable is connected, ensure vents are not blocked by tablecloths, curtains, etc.

• Do not install the product in an area with poor ventilation (e.g., on a bookshelf, in a closet).

• Install the product on a flat and stable place large enough to support it.

• When installing on a shelf or cabinet, make sure the bottom end of the product is not protruding forward.

WARNING

• Keep the product clean at all times. If it becomes covered in dust for a long time, it can cause fire or damage.

• To clean the inside of the product, you must contact the service center.

• When cleaning the product, disconnect the AC cable and wipe it gently with a soft cloth to prevent scratches.

• Do not physically come in contact with the screen of the LED Package.

• To clean the product, use an air gun to lightly remove dust from the front frame and the screen. If there are foreign substances between the LEDs, it may cause a defect.

CAUTION

• When cleaning the product or screen, unplug the power cord and wipe gently with a soft cloth. Do not spray water or other liquids directly on the product. Do not clean with chemicals like glass cleaner, air freshener, insecticide, lubricants, wax, abrasive, thinner, benzene, alcohol, etc.

WARNING

• Do not use the product in any environment with excessively high temperatures or humidity.

• If you use the product for a long period, take a rest from time to time to protect your vision.

• If water or any foreign substance enters a unit, turn it off, disconnect the AC cable, and contact the service center.

• If no image appears or no sound is heard, stop using the product and disconnect the AC cable.

• Do not drop an object or impact the product or screen.

• If there is smoke or a strange sound or smell, disconnect the AC cable and contact the service center.

• Do not attempt to disassemble, repair or modify the product yourself.

• Do not place objects filled with liquids on or over the product.

• Do not push hard on or scratch the product’s surface with your hands or sharp objects.

• Do not use high voltage electrical goods near the product (e.g., a bug zapper).

• To shut off the power of the unit, you must disconnect all connected AC cables.

CAUTION

• This panel is an advanced product containing millions of pixels. You may occasionally see pixel spots. This is not a defect.

• Do not put or store inflammable substances near the product.

• Keep the proper distance from the product to avoid eye strain.

• Set the appropriate resolution and frequency for the product.

• Take a regular break when working with the product for a long time.

1. When taking out the product, make sure the screen is not pressed. Use the provided Protection Pad for support.

2. To stand the product upright, hold it on both sides so that the LED package screen does not touch the floor.

3. Place the product with the LED package screen facing down. To protect the screen, lay the protective pad in the box on the floor.

4. If you do not have a pad, make sure there are no foreign objects on the floor, and then carefully place the screen facing down or up. Be careful not to drop objects on the screen.

CAUTION

• If the product is tilted towards the LED package screen, the bottom of the product may be damaged.

• If the product is tilted towards the edge of the LED package screen, the bottom corner of the product may be damaged.

Temperature

• Make a cooling system for the enclosure so that the operating temperature of the product can be maintained. The product operating temperature is 0 °C to 40 °C (32 °F to 104 °F), with a recommended room temperature below 25 °C (77 °F).

• Install in a location where the warm air from an air conditioner does not directly affect the product.

Direct Sunlight

• Install in a location that is not exposed to direct sunlight. This will prevent the screen from appearing blurry due to light reflection.

Installation Position

• Ensure the distance from the ceiling of the installation room to the product is at least 400 mm (15.7 inches).

• Ensure the distance from the floor of the installation room to the product is at least 100 mm (3.9 inches).

Installing on a Wall

• A: 30 mm (1.1 inches) or more (recommended) – Can be installed directly on our own wall mount without using a structure.

• B: 25 mm (0.9 inches) or more

• C: 60 mm (2.3 inches) or more

Installing on a Recessed Wall

• After installation on a recessed wall, a bezel can be installed for interior purposes.

• A: 30 mm (1.1 inches) or more (recommended) – Can be installed directly on our own wall mount without using a structure.

• B: 25 mm (0.9 inches) or more

• C: 60 mm (2.3 inches) or more

When Installing the Bezel

• Ensure it can be detached for product repair.

• For the top / bottom bezels, secure at least 60% of the air vent to facilitate air circulation to prevent malfunction.

You can connect to the CSAB-0122D/CSAD (System Controller) by using a LAN cable. Connect one end of the LAN cable (not provided) to the LAN IN port on the display and the other end to the System Controller.

CAUTION

• Check the direction so that the LAN cable is not damaged.

• Inserting the LAN cable with excessive force may damage the contact point.

You can connect the unit to a power disconnecting device using an AC cable.

1. Prepare the power cable of 9 A (16 AWG) or more.

2. Check the power cable color connection based on your region:

3. Use a ferrite core to block out noise from the power supply. Use 7 or more cores each for GND, L, and N when connecting to a master cabinet power cable.

4. Connect the AC cable to the screen using an angle type O-type crimp terminal to connect to the screen power supply terminals (L, G, N).

5. Secure the AC cable to the fixing parts once it is connected to the screen. Ensure it is secured near the screen (100 mm or less recommended).

If no image is displayed, check the following:

• Is the AC cable connected to the product? Make sure the AC cable is properly connected to the power disconnecting device.

• Is the ‘No Signal’ message displayed? This indicates no connection between the CSAB-0122D/CSAD and the input source. Check the connection status of the LAN cable and access the Input menu to check the input source.

• Does the ‘Invalid Mode’ message appear? Refer to the manual of CSAB-0122D/CSAD.

If you see the ‘Unknown Product’ message, check if you have installed the driver. Refer to the manual of CSAB-0122D/CSAD for instructions.

If the screen image appears abnormal, try these steps:

• Is the screen position wrong? Refer to the manual of CSAB-0122D/CSAD for adjustments.

• Is the screen displayed abnormally? The proper input source may not be connected to the port. Connect a cable that matches the input source signal.

• Does the screen flicker or shake? Check if the CSAB-0122D/CSAD is powered off.

If the display color is abnormal, consider the following:

• Does the screen have poor color resolution (16 colors)? Refer to the manual of CSAB-0122D/CSAD.

• Is the screen color unstable or looks black and white? Refer to the manual of CSAB-0122D/CSAD.

• Does a black dot appear on the screen? The few pixels (red, green, blue, white, and black) that appear on the screen are due to the inherent characteristics of the LED surface. This is not a malfunction of the Screen.

If the operation is not normal, specifically if the power suddenly turns off, refer to the manual of CSAB-0122D/CSAD for troubleshooting.