LG MAGNIT LSAB012-N2 (01) PDF Document

WARNING

• Before using an AC cable, make sure it conforms to the national standards.

• Operate the display only from a power source (i.e. voltage) indicated in the product specification. Otherwise the product can be damaged, fire can occur or you may be electrocuted. If you are not sure what type of power supply you have, consult a certified installation company.

• Be sure to connect the AC cable to a grounded power disconnecting device. If you do not you may be electrocuted or injured or the product can be damaged.

• Insert the AC cable securely so that it does not come loose. Poor connection may cause a fire or electric shock.

• In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. It can cause electric shock.

• Be careful not to place heavy objects (electronic appliances, clothes, etc.) on or step on the AC cable. In addition, do not bend or pull the AC cable with excessive force. Damaged power cords may cause a fire or electric shock.

• Do not connect the AC cable to a power disconnecting device if it has been damaged by a sharp object. You may be electrocuted.

• Do not insert a conductor (such as a metal chopstick) into the power disconnecting device while the AC cable is connected on the other side of the same power disconnecting device. In addition, do not touch the AC cable directly after removing it from the power disconnecting device. You may be electrocuted.

• If water or any foreign substance enters the product, disconnect the AC cable immediately and contact the service center. Otherwise, this may cause a fire or electric shock due to damage to the product.

• Keep the AC cable away from heating devices. The cord coating may melt and cause fire or electric shock.

• Never disassemble, repair, or modify the AC cable. This may cause a fire or electric shock.

• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

• For the power consumption to be zero, the AC cable must be disconnected.

CAUTION

• If there is dust on the AC cable or the power disconnecting device, wipe them clean. Overheating due to layers of dust may cause a fire or electric shock.

• If there is moisture on the AC cable or the power disconnecting device, wipe them clean. In addition, do not touch them if your hands are wet. This may cause an electric shock.

• Do not turn the product on or off by connecting or disconnecting the AC cable. In other words, do not use the AC cable as a switch. This may cause an electric shock or product malfunction.

• Do not disconnect the AC cable while using the product. Electrical shock can damage the product.

WARNING

• Contact the service center before moving the product. It may cause electric shock and damage the product.

• Make sure the product is turned off, unplugged, and all cables have been removed before the product is moved. You may be electrocuted or the product can be damaged.

• When moving the product, do not shock or cause an impact on the front panel. You may be electrocuted or the product can be damaged.

• Use the correct number of people according to the weight of the product. (Under 25 kg (55.1 lbs) per person use lifting equipment when exceeding 100 kg (220.4 lbs)). If use the damaged product again, contact the service center because it can cause electric shock or fire.

• Do not hold it upside down while holding only the stand. (It is for stand supported models only.) This may cause stand warping, panel damage and other types of product damage.

CAUTION

• Do not dispose of the product-packing box. Use it when moving by putting the product in the box to carry it.

WARNING

• Contact the service center before installing the product. It can cause electric shock and damage the product.

• Do not drop an object on or impact on the product. Keep out of reach of children and do not place toys or objects near the product to prevent throwing things on the product screen. It can cause injury to human, problem to product and damage the display.

• Do not put heavy objects on, or hang from, the product. If the product collapses or is dropped, you may be injured.

• Do not touch the surface of the product if it overheats. It can cause injury to human.

• Install the product firmly fixed on a floor, wall, etc. to prepare against external impact such as wind and earthquake. You must refer to the manual provided.

• Prevent Children from climbing or hanging on the product. If the product collapses or is dropped, you may be injured.

• Do not install it where there are heating devices such as electrical heaters or lighting equipment. Fire, electrical shock, malfunction may occur.

• Do not install this product by yourself as you may injure yourself or cause damage to the product. Please contact service engineer authorized by service center.

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

• Do not leave the AC cable, signal cables, etc. in one’s walking path. This could cause a trip or fall, which could cause an electrical shock, fire, product breakdown, or injury.

• Do not let the product drop when connecting it to an external device connected with a short cable. This may cause injury and damage to the product.

• If you drop the product or the case is broken, turn off the product and unplug the power cord and contact the service center. If you continue to use without taking proper measures, electrical shock or fire can occur.

• Install the product in a dry place where it is not near dust and water. Avoid high temperatures and humidity. This may cause electrical shock, fire or product damage.

• Safely install the product in a place that can hold the weight of the product. A lack of strength may cause the product to fall.

• A readily accessible disconnect device shall be incorporated external to the equipment. The maximum rating of an overcurrent protective device to be provided external to the equipment may be one of the protective device ratings available in the country of installation.

• Power docking should include no more than 7 units.

CAUTION

• Install the product where no Electromagnetic Interference occurs.

• If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with service engineer before installing. Please do not install the product in places such as where there is an abundance of fine dust or oil mist, chemical substances are used, exposed to direct sunlight, the temperature is very high or low, the humidity is very high.

• Make sure the product is well ventilated by Installing at a distance (30 mm (1.1 inches) or more) from the wall. If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat buildup.

• When the AC cable is connected, make sure that the vents are not blocked by tablecloths, curtains, or other objects (such as plastic). The product can be deformed or fire can break out due to overheating inside the product.

• Do not install the product in an area with poor ventilation (e.g. on a bookshelf, in a closet) or outside and avoid placing on cushions or carpets. The product could catch fire due to overheating inside the product.

• Install the product on a flat and stable place that is large enough to support the product. If the product is dropped, you may be injured or the product may be broken.

• When installing the product on a shelf or cabinet, make sure that the bottom end of the product is not protruding forward. The product may fall due to unbalanced center of gravity, which may cause personal injury or damage to the product. Be sure to use cabinets or shelves that fit your product.

WARNING

• Keep the product clean at all times. If you don’t clean the unit for a long time and it becomes covered in dust, it can cause fire or product damage.

• When you need to clean the inside of the product, you must contact the service center. Otherwise, cleaning without support may cause a fire, electric shock, or damage to the product.

• When cleaning the product, disconnect the AC cable and wipe it gently with a soft cloth to prevent scratches. An electric shock may occur or damage to the screen if its scratched.

• Do not physically come in contact with the screen of the LED Package. This may cause damage to the product.

• To clean the product, use an air gun to lightly remove dust from the front frame and the screen. If there are foreign substances in between the LEDs on the screen, it may cause a defect on the screen.

CAUTION

• When cleaning the product or the screen, unplug the power cord and wipe it gently with a soft cloth. Do not spray water or other liquids directly on the product. Especially, do not clean your product with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol, etc., which can damage the product or its panel. This may result in fire, electric shock or product damage (deformation, corrosion or breakage).

WARNING

• Do not use the product in any environment with excessively high temperatures or humidity. It may cause electrical shock or damage the product.

• If you use the product for a long period of time, take a rest from time to time to protect your vision. Extended viewing could result in impaired vision.

• Listening at high volume or using for a long time can cause damage to your hearing.

• If water or any foreign substance enters a unit, turn off the unit, disconnect it from the AC cable, and contact the service center. Otherwise, the product may cause fire or electric shock.

• In the event that no image appears on the screen or no sound is heard, stop using the product. Disconnect the AC cable from the power disconnecting device immediately and contact the service center. Otherwise, the product may cause fire or electric shock.

• Do not drop an object or impact on the product or screen. It can cause injury to human, problem to product and damage the screen.

• If there is smoke or a strange sound or smell, disconnect the AC cable and contact the service center. If you continue to use the product without taking proper measures, it may cause electrical shock or fire.

• Do not attempt to disassemble, repair or modify the product yourself. Please contact service center if you need to repair it. Fire or electric shock can occur.

• Do not place objects filled with liquids such as vases, cups etc. on or over the product to prevent liquid from entering the product. Failure to do so may result in fire, electric shock, malfunction or deformation.

• Do not use high voltage electrical goods near the product (e.g., a bug zapper). This may result in product malfunction if it receives an electrical shock.

• Keep small accessories out of the reach of children. If a child swallows it, consult a doctor immediately.

• Keep out of reach of children from the product. Also, do not throw toys or objects at the product or screen. It can cause injury to human, problem to product and damage the screen.

• To shut off the power of the unit, you must disconnect all connected AC cables.

CAUTION

• This panel is an advanced product that contains millions of pixels. You may occasionally see pixel spots when viewing the screen. Since these deactivated pixels are not a defect, the performance and reliability of the product is not affected.

• Do not put or store inflammable substances near the product. There is a danger of explosion or fire.

• Keep the proper distance from the product. It can cause damage to your vision if you look at the product too closely.

• Set the appropriate resolution and frequency by products. It can cause damage to your vision.

• Take a regular break when working with the product for a long time.

• Do not dispose of this product with general household waste.

• Disposal of this product must be carried out in accordance to the regulations of your local authority.

1. When taking out the product, make sure the screen is not pressed.

2. To stand the product upright, hold it on both sides so that the LED package screen does not touch the floor.

3. Place the product with the LED package screen facing down. To protect the screen, lay the protective pad in the box on the floor.

4. If you do not have a pad, make sure that there is no foreign object on the floor when you lay the product on the floor, and then carefully place the LED package screen facing down or up. Be careful not to drop objects on the LED package screen.

CAUTION

• If the product is tilted towards the LED package screen, the bottom of the product may be damaged.

• If the product is tilted towards the edge of the LED package screen, the bottom (corner) of the product may be damaged.

Temperature

• Make a cooling system for the enclosure so that the operating temperature of the product can be maintained.

• Product operating temperature: 0 °C to 40 °C (32 °F to 104 °F) (the recommended room temperature is below 25 °C (77 °F).)

• Install in a location where the warm air from an air conditioner does not directly affect the product. This will prevent malfunctions such as the screen turning off.

Direct Sunlight

• Install in a location that is not exposed to direct sunlight. This will prevent the screen from appearing blurry due to light reflection.

Installation Position

• Ensure the distance from the ceiling of the installation room to the product is at least 400 mm (15.7 inches). The high temperature air collected at the ceiling will naturally circulate to prevent malfunction.

• Ensure the distance from the floor of the installation room to the product is at least 100 mm (3.9 inches). The air from the floor will easily circulate to the ceiling to prevent malfunctions.

Installation Location Clearances

• Installing on a Wall:

– A: 30 mm (1.1 inches) or more (recommended) – Can be installed directly on our own wall mount without using a structure.

– B: 25 mm (0.9 inches) or more

– C: 60 mm (2.3 inches) or more

• Installing on a Recessed Wall: After installation on a recessed wall, a bezel can be installed for interior purposes.

– A: 30 mm (1.1 inches) or more (recommended) – Can be installed directly on our own wall mount without using a structure.

– B: 25 mm (0.9 inches) or more

– C: 60 mm (2.3 inches) or more

When Installing the Bezel

• Ensure it can be detached for product repair.

• For the top / bottom bezels, secure at least 60 % of the air vent to facilitate air circulation. This will prevent malfunction.

You can connect the LG MAGNIT LSAB012-N2 to the CSAB-0122D/CSAD (System Controller) by using a LAN cable. Connect the LAN cable (*Not provided) from the LAN IN port on the screen to the corresponding port on the System Controller.

CAUTION

• Check the direction so that the LAN cable is not damaged.

• Inserting the LAN cable with excessive force may damage the contact point.

You can connect the LG MAGNIT LSAB012-N2 to a power disconnecting device using an AC cable.

• Use the AC cable to connect to the power disconnecting device. (Please use a cable that is long enough to be connected to the screen.)

• Please use a ferrite core to block out the noise from the power supply.

• Please use 7 or more cores each to GND, L, and N when connecting to a master cabinet power cable. * Manufacturer: TNC CO.,LTD.

• Connect the AC cable to the screen using an angle type O-type crimp terminal to connect to the screen power supply.

• The AC cable needs to be secured to the fixing parts once it is connected to the screen. (Make sure it is secured near the screen. * 100 mm (3.9 inches) or less recommended)

Power Connection Requirements:

• Prepare the power cable of 9 A (16 AWG) or more.

• Check power cable color connection.

• Avoid water or dust.

AC Cable Color Codes by Country:

The On/Off Scheduler, found under Ez Setting, allows you to set a schedule to use your signage by time and day of the week.

• [On/Off Time Setting]: Set on/off times for each day of the week.

• [Holiday Setting]: Set holidays by date and by day of the week.

The Fail Over feature, located in Ez Setting, sets the priority of input devices for when a fault occurs. It can automatically play content stored in the device or run a set app.

• [On/Off]: Turns Fail Over on or off.

• [Input Priority]: Set the priority of input sources for fail over.

• [Backup via storage]: When there is no input signal, this feature automatically plays the content stored in the device or runs the set app. When set to [On], [Auto], [Manual], [SuperSign Contents], and [SI App / Play via URL] items are activated.

– [Auto]: When the automatic input switches due to taking screenshots of an image or video that is playing at regular intervals, this feature will play back the file. The time interval can be set to 30 min, 1 hour, 2 hours and 3 hours.

– [Manual]: When the automatic input switches due to the image and video file being uploaded, the feature will play back the file.

– [SuperSign Contents]: When the automatic input switches, this feature will play the file(s) distributed in SuperSign CMS.

– [SI App / Play via URL]: Run SI App or Play via URL when automatic input switch occurs.

• [reset]: Reset to initial settings.

The Status Mailing feature, found in Ez Setting, configures the system to assess the device’s status and notify an administrator by e-mail.

• [On/Off]: Turns Status Mailing on or off.

• [Mailing Option], [Scheduling]: Sets the email sending interval.

• [User E-mail Address]: Set the user email address of the sender.

• [Sending Server(SMTP)]: Set the address of the SMTP server.

• [ID]: Enter the account ID of the sender.

• [Password]: Enter the password for the sender’s account.

• [Receiver E-mail Address]: Set the email address of the recipient.

• [Send message]: Immediately assess the status of the device and deliver the information to the specified email address.

• [reset]: Reset to initial settings.

The Multi Screen feature, located in Ez Setting, allows you to view multiple external inputs and videos on a single screen. Supported modes include PIP Mode, PBP Mode, 3-Screen Split Mode, and 4-Screen Split Mode.

Selecting Screen Layout

When you enter multi-screen mode without having set any screen layout, the screen layout selection menu appears. When the screen layout selection menu is not displayed on the screen, go to the screen layout menu bar by pressing the up arrow key on your remote control and select your desired screen layout. If you want to close the screen layout menu, press the back key.

Changing Screen Input

Press the button on the top right of each split screen to select the desired input.

Playing Videos on Split Screens

Press the button on the upper right of each split screen, select Video File, and then select a storage device to view the list of videos. Select your desired video from the list to play it.

Power-related settings can be found under General -> Power.

• [No Signal Power Off (15 Min)]: If set to [On], the product turns off after it has remained in a No Signal status for 15 minutes.

• [No IR Power Off (4hour)]: If set to [On], the product turns off if there is no input from the remote control for 4 hours.

• [DPM] / [DPM (Standby Mode)]: Sets the Display Power Management (DPM) mode. If not set to [Off], the monitor will enter DPM mode when there is no input signal.

• [PM Mode]: Options include [Power Off (Default)], [Sustain Aspect Ratio], [Screen Off], [Screen Off Always], and [Network Ready].

• [Power On Delay](0-250): Prevents overload by implementing a power-on delay (0 to 250 seconds) when multiple monitor sets turn on.

• [Power On Status]: Selects the operating status of the monitor when the main power has turned on. Choose from [PWR (Power On)], [STD (Standby)], and [LST (Last Status)].

The lock features are located under Admin -> Lock Mode.

• [Home Dashboard Lock]: When set, you can limit changes in the settings of the Home Dashboard.

• [USB Lock]: Configures the USB lock feature so that settings or content cannot be changed.

• [OSD Lock]: Configures the OSD lock feature so that settings or content cannot be changed. Press and hold the Settings key for at least 10 seconds and enter the password to access.

• [IR Operation Lock]:

– [Off (Normal)]: You can use your remote control.

– [On (Power Key Only)]: You can only use the power key.

– [On (Block All)]: You cannot use your remote control (However, Power On feature is available).

• [Local Key Lock]:

– [Off (Normal)]: You can use the local keys on the monitor.

– [On (Power Key Only)]: You can only use the power key.

– [On (Block All)]: You cannot use the local keys (However, Power On feature is available).

• [Wi-Fi Lock]: Enables you to turn the Wi-Fi feature on or off.

• [Screen Share Lock]: Enables you to turn the Screen Share feature on, off, or off with a PIN.

This feature, located under Admin -> Change Password, enables you to set the password you use to enter the Installation menu. The default password is: 000000.

1. Enter your current password.

2. Enter a new 6-digit password.

3. Enter the same password again in the Confirm Password field for confirmation.

Located under Admin -> Factory Reset, this option initializes all settings in [Setting] and files from the internal storage. The exceptions are RGB gain value of [Calibration] mode, [Video Wall] items, [Server Setting] items of [Ez Setting], and [Set ID] items of [General].

Supported video codecs:

Maximum transmit ratio:

Supported Photo File Formats:

• Only USB storage devices are recognized.

• USB storage devices connected to the monitor through a USB hub may not work properly.

• The recognition speed of a USB storage device may depend on each device.

• Please do not turn off the display or unplug the USB device when the connected USB storage device is working. When the device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.

• Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause the product to malfunction or fail to be played. Remember to only use USB storage devices that store normal files.

• Please connect power to a USB storage device (over 0.5 A) which requires an external power supply. Otherwise, the device may not be recognized.

• Some USB storage devices may not be supported or operated smoothly.

• Be sure to back up important files since data stored in a USB memory device may be damaged. We will not be responsible for any data loss.

• If the USB HDD does not have an external power source, the USB device may not be detected. So make sure to connect it to an external power source.

• The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB memory.

• USB storage devices (USB 2.0 or below) are also supported. However, they may not work properly in the videos list.

• A maximum of 999 folders or files can be recognized under one folder.

This feature enables you to group together multiple monitor sets on a single network to distribute content or copy setting data on a group basis. It has two modes: Master and Slave.

[GROUP MANAGEMENT]

• Creating a New Group

1. Click [Add New Group].

2. Enter a group name.

3. Click [Add Device], select the devices you wish to add to the group, and add them.

4. Click [Done], and you will see that a new group has been created.

• Editing a Group

1. Click the group you wish to edit.

2. Add a new device by using [Add Device].

3. Delete a device by using [Delete Device].

4. Check whether the devices in the group are connected to a network by using [Device Check].

5. If there are any sets of devices in the group that are not [Data Cloning] or content synchronized, [Data Cloning] or [Synchronize] button will be activated.

6. You can re-copy the master device’s setting data to the group by using [Data Cloning].

7. You can re-distribute the content distributed to the group by using [Synchronize].

• Deleting a Group

1. Click [Delete Group].

2. Select the group you wish to delete and click [Delete].

3. Check that the group you selected has been deleted.

[Setting Data Cloning]

1. Select your desired group and click Clone.

2. Check that the data have been copied on the slave sets.

[Content Distribute]

1. Select the type of content you wish to distribute (Schedules or Playlists).

2. Select the content you wish to distribute.

3. Select the group to which you wish to distribute the content and click [Distribute].

4. Run the Content Manager app on the slave sets and check that the content has been distributed.

This feature allows the screen of a user’s device such as a mobile or PC Windows to be shared with a display using a wireless connection such as WiDi or Miracast.

To use ScreenShare, go to INPUT -> ScreenShare.

1. Connect according to the instructions provided by the guide that can be accessed through the CONNECTION GUIDE button in the upper right.

2. Once the connection is established, Screen Share between the user device and the monitor is enabled.

Some key codes may not be supported depending on the model.

• Baud Rate: 9600 BPS

• Data Length: 8 bits

• Parity Bit: None

• Stop Bit: 1 bit

• Flow Control: None

• Communication Code: ASCII

• Is the AC cable connected to the product?

– Make sure the AC cable is properly connected to the power disconnecting device.

• Is the ‘No Signal’ message displayed?

– There is no connection between CSAB-0122D/CSAD and the input source. Check the connection status of the LAN cable.

– Access the Input menu to check the input source.

• Does the ‘Invalid Mode’ message appear?

– Refer to the manual of CSAB-0122D/CSAD.

• Is the screen position wrong?

– Refer to the manual of CSAB-0122D/CSAD.

• The screen is displayed abnormally.

– The proper input source is not connected to the port. Connect a cable that matches the input source signal.

• The screen flickers or shakes.

– Check if CSAB-0122D/CSAD is powered off.

• Screen has poor color resolution (16 colors).

– Refer to the manual of CSAB-0122D/CSAD.

• The screen color is unstable or looks black and white.

– Refer to the manual of CSAB-0122D/CSAD.

• Does a black dot appear on the screen?

– The few pixels (red, green, blue, white and black) that appear on the screen are due to the inherent characteristics of the LED surface. This is not a malfunction of the Screen.

• The power suddenly turned off.

– Refer to the manual of CSAB-0122D/CSAD