LG 42LM6200-UE (01) PDF Document

To clean your LG 42LM6200-UE regularly to keep the best performance and to extend the product lifespan, follow these steps:

1. Make sure to turn the power off and disconnect the power cord and all other cables first.

2. For the screen, frame, cabinet, and stand:

– To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

– To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.

3. For the power cord:

– Remove the accumulated dust or dirt on the power cord regularly.

CAUTION:

– Do not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in scratches on the screen and image distortions.

– Do not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners, or lubricants, as these may damage the screen’s finish and cause discoloration.

– Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.

When moving or lifting the LG 42LM6200-UE, read the following to prevent the TV from being scratched or damaged and for safe transportation:

– Make sure the product is turned off, unplugged, and all cables have been removed.

– Avoid touching the screen at all times, as this may result in damage to the screen.

– It is recommended to move the TV in the box or packing material that the TV originally came in.

– When holding the TV, the screen should face away from you to avoid damage.

– When transporting a large TV, there should be at least 2 people.

– When transporting the TV by hand, hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

– When transporting the TV, do not expose it to jolts or excessive vibration.

– Keep the TV upright; never turn the TV on its side or tilt towards the left or right.

– Do not press or put stress on the front panel of the TV.

If a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and is not covered by the warranty. To prevent image burn on your LG 42LM6200-UE, follow these guidelines:

– Avoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD).

– If the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.

Viewing Environment:

– Viewing Time: When watching 3D contents, take 5-15 minute breaks every hour. Viewing 3D contents for a long period of time may cause headache, dizziness, fatigue or eye strain.

– Viewing Distance: Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you feel discomfort, move further away from the TV.

Viewing Age:

– Infants/Children: Viewing 3D contents for children under the age of 5 is prohibited. Children under 10 may overreact, and special monitoring is required.

– Teenagers: Teenagers under the age of 19 should be advised not to watch 3D videos for a long time when they are tired.

– Elderly: The elderly may perceive less of a 3D effect. Do not sit closer to the TV than the recommended distance.

Health Precautions:

– Some users may experience a seizure or other abnormal symptoms when exposed to a flashing light or particular pattern from 3D contents.

– Do not watch 3D videos if you feel nausea, are pregnant, or have a chronic illness such as epilepsy, cardiac disorder, or blood pressure disease.

– If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D contents.

Symptoms Requiring Discontinuation:

– Stop watching 3D contents if you experience fatigue, headache, eyeball pain, dizziness, nausea, palpitation, blurriness, discomfort, double image, or visual inconvenience.

– Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.

– Do not use 3D glasses instead of your normal glasses, sunglasses, or protective goggles.

– Using modified 3D glasses may cause eye strain or image distortion.

– Do not keep your 3D glasses in extremely high or low temperatures, as it will cause deformation.

– The 3D glasses are fragile and are easy to be scratched. Always use a soft, clean piece of cloth when wiping the lenses. Do not scratch the lenses with sharp objects or clean/wipe them with chemicals.

When you turn the TV on for the first time, the Initial setting screen appears. Follow these steps to customize the basic settings:

1. Connect the power cord to a power outlet.

2. In Standby mode, press the power button on the remote control to turn the TV on.

3. Follow the on-screen instructions to customize your TV settings according to your preferences:

– Language Selection: Selects a language to display.

– Using the Magic remote control: Sets the Magic remote control.

– Environment Selection: Select Home for the home environment. The Store mode puts the TV in demo mode.

– Time Zone Setting: Selects the time zone and daylight saving (Depending on country).

– Network Connection: Sets your network to enable network-related features on the TV.

– Auto Tuning: Scans and saves available channels automatically.

– Auto Energy Saving mode Setting: Selects Auto Energy Saving mode.

– 3D-On-Start Setting: Selects 3D-On-Start option (For 3D TV).

– Setting is completed: Confirms the setting options.

4. When the basic settings are complete, press the Wheel (OK) button.

5. To turn the TV off, press the power button on the remote control.

To attach the stand to your LG 42LM6200-UE, follow these instructions:

1. Place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

2. Assemble the Stand Body to the Stand Base.

3. Attach the assembled stand to the back of the TV set using the 4 provided screws (M4 x 20).

4. Tighten the screws firmly to prevent the TV from tilting forward.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a 10 cm (4 inches) minimum space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

To adjust the angle of the TV to suit your view, you can swivel it 10±2 degrees to the left or right.

To prevent the TV from falling over, tipping, shaking, or rocking, it should be securely attached to the floor/wall.

Securing to a Table (Depending on model):

1. Connect the Desk-mount Cables to the Stand Base using the Bracket Screws.

2. Fix the Desk-mount Cables to a table using the Desk-mount Screws.

3. Once the TV is fixed, move the table close to the wall.

Securing to a Wall (Optional):

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts already inserted in the eye-bolts position, remove them first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

1. Gather and bind the cables with the cable holder.

2. Fix the cable management clip firmly to the TV.

CAUTION: Do not move the TV by holding the cable holder, as the cable holders may break, and injuries and damage to the TV may occur.

Antenna or Cable:

Connect your antenna or cable box to the ANTENNA / CABLE port using a coaxial (75Ω) RF cable.

HDMI Connection (Best Quality):

Connect your HD receiver, DVD/Blu-Ray player, or other device using an HDMI cable to any of the HDMI IN ports. For Audio Return Channel (ARC) functionality, use the HDMI IN 1 (ARC) port.

DVI to HDMI Connection:

Connect your device using a DVI-HDMI cable to an HDMI IN port. For audio, connect a separate audio cable from the device’s audio out to the TV’s (RGB/HDMI-PC) AUDIO IN port.

Component Connection:

Connect the component video (Green/Pb, Blue/Pr, Red/Y) and audio (Red, White) cables to the corresponding colored ports in the COMPONENT IN section.

Composite Connection:

Connect the composite video (Yellow) and audio (Red, White) cables to the corresponding colored ports in the AV IN section.

PC Connection:

You can connect a PC using an HDMI cable (recommended), a DVI-to-HDMI cable with a separate audio cable, or an RGB (VGA) cable with a separate audio cable.

External Audio System:

Connect your audio system using an optical audio cable from the TV’s OPTICAL DIGITAL AUDIO OUT port to your system’s optical input. You should then set the TV speaker feature to off in the TV’s menu.

USB Device:

Connect a USB flash drive, external hard drive, or USB memory card reader to any of the USB IN ports to access multimedia files via the Smart Share menu.

Replacing Batteries:

When the message “Magic remote control battery is low. Change the battery.” is displayed, open the battery cover, replace the batteries with two 1.5 V AA batteries matching the (+) and (-) ends, and close the cover.

Registering the Remote:

To register the remote control for the first time, press the Wheel (OK) button on the remote control while pointing it at the TV.

Re-registering the Remote:

If registration fails or you need to re-register, press and hold the BACK and HOME buttons together for 5 seconds to reset it. Then, try registering it again by pressing the Wheel (OK) button.

Using the Pointer:

If the on-screen pointer disappears, move the remote control slightly to the left or right, and it will automatically reappear. If you press a navigation button while moving the pointer, the pointer will disappear and the remote will work like a regular remote.

1. Press the HOME button on the remote to access the HOME menu.

2. Select User Guide from the menu and press the Wheel (OK) button.

Cannot control the TV with the remote control.

– Check the remote control sensor on the product and try again.

– Check if there is any obstacle between the product and the remote control.

– Check if the batteries are still working and properly installed (+ to +, – to -).

No image display and no sound is produced.

– Check if the product is turned on.

– Check if the power cord is connected to a wall outlet.

– Check if there is a problem in the wall outlet by connecting other products.

The TV turns off suddenly.

– Check the power control settings. The power supply may be interrupted.

– Check if the Auto sleep feature is activated in the Time settings.

– If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

All of the buttons are touch sensitive and can be operated through simple touch with your finger.