LENOVO LEGION PRO 5 16IRX10 D1 (01) PDF DOCUMENT

The camera light on your LENOVO LEGION PRO 5 16IRX10 D1 indicates whether the camera is activated. The statuses are as follows:

The power light on your LENOVO LEGION PRO 5 16IRX10 D1 indicates the current power state of the PC. The different statuses are:

The color of the power light on your LENOVO LEGION PRO 5 16IRX10 D1 can indicate the PC’s active operation mode. The color meanings are as follows:

The charging light on your LENOVO LEGION PRO 5 16IRX10 D1 indicates if the PC is plugged in and the battery’s charge level. The statuses are:

A USB connector on your LENOVO LEGION PRO 5 16IRX10 D1 with a battery icon supports the always-on function. This allows the PC to supply power to a connected USB device even when the PC is powered off, in sleep mode, or in hibernation mode.

The always-on function can be turned on and off in:

The PC’s firmware setup utility, or

Lenovo Vantage or Lenovo PC Manager

Your LENOVO LEGION PRO 5 16IRX10 D1 is equipped with a camera switch, which is a toggle switch used to enable or disable the built-in camera for privacy protection. If you don’t need to use the camera, slide the switch to the off position to prevent any apps from using it. This is a mechanical button that prevents any attempt from capturing your image. If you slide the camera switch to disable it during a video call, other people on the call will not be able to see you.

The specifications for the LENOVO LEGION PRO 5 16IRX10 D1 are as follows:

Dimensions

AC Power Adapter

Battery Pack

Memory

Mass Storage Device

Screen

Connectors and Slots

USB Connectors

Depending on many factors such as the processing capability of the host and peripheral devices, file attributes, and other factors related to system configuration and operating environments, the actual transfer rate using the various USB connectors on your LENOVO LEGION PRO 5 16IRX10 D1 will vary and will be slower than the data rate listed below for each corresponding device.

The operating environment requirements for your LENOVO LEGION PRO 5 16IRX10 D1 are as follows:

Maximum altitude (without pressurization): 3048 m (10 000 ft)

Temperature:

At altitudes up to 2438 m (8000 ft):

Operating: 5°C to 35°C (41°F to 95°F)

Storage: 5°C to 43°C (41°F to 109°F)

At altitudes above 2438 m (8000 ft):

Maximum temperature when operating under the unpressurized condition: 31.3°C (88°F)

Note: When you charge the battery, its temperature must be no lower than 10°C (50°F).

Relative humidity:

Operating: 8% to 95% at wet-bulb temperature 23°C (73°F)

Storage: 5% to 95% at wet-bulb temperature 27°C (81°F)

CAUTION: When the computer is operating, it should be placed on a hard and flat surface with its bottom area not in contact with user’s bare skin. Under normal operating conditions, the temperature of the bottom surface will remain within an acceptable range as defined in IEC 62368-1, but such temperatures can still be high enough to cause discomfort or harm to the user if directly touched for over 10s at a time. As such, it is recommended that users avoid prolonged direct contact with the bottom of the computer.

When you turn on your LENOVO LEGION PRO 5 16IRX10 D1 for the first time, the Windows operating system will guide you through the initial setup process. Most importantly, you will:

Create a user account

Connect to a wireless network that has Internet access

Select language-related settings

Note: If you choose to set up Windows for personal use, you must either use an existing Microsoft account or create a new one. You can switch to a local account after the initial setup.

Windows provides several recovery options on your LENOVO LEGION PRO 5 16IRX10 D1 to help restore your system to normal functionality. The table below will help you choose the right option for different situations.

Resetting Windows allows you to reinstall the operating system while retaining your personal files. This gives the operating system a fresh start and, in some cases, restores the PC’s original performance.

Step 1. Select Settings → System → Recovery.

Step 2. Under recovery options, select Reset PC. When prompted, choose between Keep my files and Remove everything.

Step 3. Follow the on-screen instructions to complete the reset process.

It is advisable to create a recovery drive after completing the initial setup of Windows. If you encounter a significant issue that prevents Windows from starting, you can use the recovery drive to restore the operating system on your PC.

Step 1. Prepare an empty USB drive with a storage capacity of 32 GB or more.

Step 2. In the search box on the taskbar, type Create a recovery drive and select the matched app.

Step 3. Make sure Back up system files to the recovery drive checkbox is selected and select Next.

Step 4. When prompted, connect the USB drive to your PC, select it, and then select Next.

Step 5. Select Create.

If the Windows operating system on your LENOVO LEGION PRO 5 16IRX10 D1 fails to start, you can use a previously created recovery drive to restore Windows.

Step 1. Shut down your PC.

Step 2. Connect the recovery drive to your PC.

Step 3. Press the Novo button or the Lenovo Smart Key to open the Novo button menu.

Step 4. Select Boot Menu.

Step 5. Select the USB drive as the boot device. The PC will start to the Windows Recovery Environment.

Step 6. Follow the on-screen instructions to restore Windows onto your PC.

You can adjust the timeout settings for your LENOVO LEGION PRO 5 16IRX10 D1 to enter sleep mode and for the built-in screen to turn off, which is an effective method of reducing power consumption.

Step 1. Select Start → Settings → System → Power & battery → Screen, sleep, & hibernation timeouts.

Step 2. Adjust the settings. For notebook PCs, you can set distinct timeouts for two usage scenarios: when the PC is plugged in and when it is running on battery power.

The default timeout settings are as follows:

Note: To wake the PC from sleep mode, press the power button or any key on the keyboard.

Step 1. Plug an Ethernet cable into the Ethernet connector on your LENOVO LEGION PRO 5 16IRX10 D1.

Step 2. Plug the other end of the Ethernet cable into a network wall jack or a router.

Ensure that you have a secure Wi-Fi network account and the required credentials.

Step 1. Select the network icon on the bottom right of your display.

Step 2. Select an available network, and then select Connect. If you want to be automatically connected to this Wi-Fi network the next time you start your computer, select Connect automatically before selecting Connect.

Step 3. Input your credentials if necessary, and then follow the on-screen instructions to connect to the desired Wi-Fi network.

Your LENOVO LEGION PRO 5 16IRX10 D1 may come with the following unique Lenovo apps:

Lenovo Vantage: A one-stop solution to help you update your computer, configure hardware settings, and access personalized support.

Smart Connect: An app that can easily pair your PC with your Motorola smartphone and Lenovo tablet. With Smart Connect, you can:

Access mobile apps on your PC

Quickly share content between connected devices

Mirror your phone display or create a virtual phone screen on your PC

Copy and paste across connected devices

Use your phone or tablet camera as the PC webcam

Control your phone or tablet using your PC keyboard and mouse

Extend or mirror your PC display on the tablet

Lenovo AI Now: Your personal and private AI assistant. It enables you to boost your productivity by building your personal knowledge library, helps you with inspiration, writing and summarizing, and provides troubleshooting and quick settings for your PC.

Legion Space: An app developed specifically to help you access game resources, adjust the performance, change light effects, and manage devices and peripherals.

The Novo Button menu can be displayed before the operating system starts. From the menu, you can choose to:

Open the UEFI/BIOS setup utility

Open the boot device selection menu

Open the Windows startup options screen

To open the Novo Button menu:

Step 1. Turn off the computer.

Step 2. Open the LCD screen and press the Novo button.

Note: Alternatively, turn on or restart the computer, press F9 repeatedly to open the Novo Button menu.

Hotkeys on your LENOVO LEGION PRO 5 16IRX10 D1 provide quick access to frequently used settings and applications. The functions are as follows:

The fn lock is an electronic switch that affects how you use hotkey functions. To turn it on and off, press fn + esc. The esc key has an LED that indicates the status of the fn lock switch. A Lenovo keyboard usually contains hotkeys in the top row that share keys with the function keys (F1-F12). The function of the fn lock is as follows:

The fn key on your LENOVO LEGION PRO 5 16IRX10 D1 can be used in combination with specific keys to adjust device settings or activate additional functions.

The Windows logo key on your LENOVO LEGION PRO 5 16IRX10 D1 can be used alone or in combination with specific keys to quickly change settings and access utilities.

The Windows operating system on your LENOVO LEGION PRO 5 16IRX10 D1 supports multi-finger gestures on the touchpad.

To modify the default functions for three-finger touchpad gestures:

Step 1. Select Settings → Bluetooth & devices → Touchpad.

Step 2. Under Three-finger gestures, use the drop-down lists to modify the functions for the swipe or tap gestures.

Ensure that both your LENOVO LEGION PRO 5 16IRX10 D1 and the display support Miracast® technology, and that the display is connected to the same Wi-Fi network as your computer and is discoverable.

Step 1. Press Windows key + K. The computer searches for wireless display devices and audio devices and lists the results.

Step 2. Select the display you want to connect to, and then follow the on-screen instructions.

The night light feature in Windows 11 enables users to switch to warmer color tones, reducing blue light emission to alleviate eye strain or fatigue.

Step 1. Open the quick settings menu by selecting the network, sound, or battery icons on the far right of the taskbar or by using the keyboard shortcut Windows logo key + A.

Step 2. Select the button for night light to turn it on or off.

Note: Some Windows 11 versions allow users to customize their quick settings. If the night light button is not visible, you can add it to the quick settings menu by selecting the edit button.

If Windows 11 night light mode is turned on, you can adjust the color temperature of the screen.

Step 1. Select Start → Settings.

Step 2. Select System → Display → Night light settings.

Step 3. Move the slider to adjust the color temperature.

Note: Selected Lenovo PCs are low blue-light certified. These PCs undergo testing with the night light turned on and the color temperature value set at 48 or above.

Smart Noise Cancelling is a noise reduction feature available on some Lenovo product models. By filtering out input and output noises, Smart Noise Cancelling enhances your audio experience.

The battery packs of your LENOVO LEGION PRO 5 16IRX10 D1 support multiple charging modes that are suitable for different power usage habits. You can switch the battery’s active charging mode in Lenovo Vantage or Lenovo PC Manager.

Normal mode: The most basic charging mode. It typically takes 2 to 4 hours for the battery to charge from 0% to 100%.

Rapid charge mode: If you want the battery to be charged faster than in normal mode, switch to rapid charge mode. The following table lists the typical time needed for batteries in rapid charge mode.

Conservation mode: If your computer is constantly plugged into an electrical outlet, consider switching to conservation mode. In conservation mode, the battery will not be fully charged. Instead, the battery’s charge will be kept within 75%-80%. This is beneficial to the long-term health of the battery.

Overnight charge optimization: This feature is for users with a regular pattern of use. When enabled, the computer adapts its charging behavior based on observation of when you plug in the computer at night and unplug it in the morning. During the nighttime, the battery is charged to a particular range and kept there for an extended period, before being further charged to 100%. This ensures safe charging and is beneficial to the long-term health of the battery.

If your LENOVO LEGION PRO 5 16IRX10 D1 is constantly plugged in to an electrical outlet and the battery rarely discharges, the battery may not be charged to its full capacity even if the battery meter reports 100% charge. You can recover the battery’s full charging potential by discharging and re-charging it.

Step 1. Unplug the computer and use it until the battery charge drops below 20%.

Step 2. Plug in the computer and charge the battery to 100%.

Yes, the USB Type-C connector with an icon USB-PD next to it on the left side of the computer conforms to the USB Power Delivery Specification. You can use a qualified USB Type-C charger (purchased separately) that is also Power Delivery compliant to charge the computer in sleep or powered-off state. Lenovo branded USB Type-C chargers with the following listed maximum ratings are tested to work with the computer:

20 V, 4.75 A

20 V, 5 A

20 V, 6.75 A

20 V, 7 A

CAUTION: The left USB Type-C connector is not designed as the primary power input connector. When the computer is operating, the power supplied by the USB Type-C charger may be insufficient, and the computer may not operate at its full capacity. Use the included ac power adapter whenever possible. When purchasing third-party USB Type-C chargers, choose a product that is safety approved or certified.

By default, pressing the power button puts the computer to sleep mode. You can change this behavior in the Windows Control Panel.

Step 1. Type Control Panel in the Windows search box and then press Enter. Open the control panel and view by large or small icons.

Step 2. Select the power options and then click to choose what the power button does.

Your LENOVO LEGION PRO 5 16IRX10 D1 has preset operation modes that balance performance, power consumption, and fan speed. You can switch the operation mode in the pre-installed app Legion Space or by using the key combination fn + Q.

Note: When the computer is operating on battery power or is plugged in using an under-rated power adapter, you may not be able to switch it to Performance mode.

The display of your LENOVO LEGION PRO 5 16IRX10 D1 may support dual refresh rates. A higher refresh rate provides a smoother viewing experience for videos and games. You can manually switch the refresh rate.

For Windows operation systems, the manual settings are usually found in Settings → System → Display. As a shortcut, you can also use the key combination fn + R to switch the display refresh rate.

Note: Not all displays support dual refresh rates. If you cannot find settings to change the display refresh rate, the refresh rate of the display might be fixed or cannot be manually changed.

The UEFI/BIOS is the first program that runs when a computer starts. You can change certain UEFI/BIOS settings in its setup utility.

Step 1. Turn on or restart the computer.

Step 2. When the Lenovo logo appears on the screen, press F2 repeatedly. Or enter Novo Button menu.

Step 3. On the welcome screen, select More Settings.

Occasionally, you may need to start the computer with a program or boot manager loaded from another device or a network location. To do this:

Step 1. Turn on or restart the computer.

Step 2. Press F12.

Step 3. From the boot device menu, select a boot device to start the computer.

To make a permanent change on boot devices, open the UEFI/BIOS setup utility. Select the Boot menu; in the UEFI Boot Order section, select the desired boot device and move it to the top of the device list. Save changes and exit.

You can set various types of passwords in the UEFI/BIOS setup utility to secure your LENOVO LEGION PRO 5 16IRX10 D1.

Notes:

All passwords set in the setup utility consist of alphanumeric characters only.

If you start the setup utility using the user password, you can only change a few settings.

Set administrator password:

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security → Set Administrator Password and press Enter.

Step 3. Enter a password string that contains only letters and numbers and then press Enter.

Step 4. Enter the password again and press Enter.

Step 5. Select Exit → Exit Saving Changes.

Change or remove administrator password:

Step 1. Open the UEFI/BIOS setup utility using the administrator password.

Step 2. Select Security → Set Administrator Password and press Enter.

Step 3. Enter the current password.

Step 4. In the Enter New Password text box, enter the new password.

Step 5. In the Confirm New Password text box, enter the new password again. (Note: To remove the password, press Enter in both text boxes without entering any character).

Step 6. Select Exit → Exit Saving Changes.

Set user password:

You must set the administrator password before you can set the user password.

Step 1. Open the UEFI/BIOS setup utility using the administrator password.

Step 2. Select Security → Set User Password and press Enter.

Step 3. Enter a password string that contains only letters and numbers and press Enter. The user password must be different from the administrator password.

Step 4. Enter the password again and press Enter.

Step 5. Select Exit → Exit Saving Changes.

Enable power-on password:

If the administrator password has been set, you can enable the power-on password to enforce greater security.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security → Power on Password and press Enter.

Step 3. Change the setting to Enabled.

Step 4. Select Exit → Exit Saving Changes.

Set hard disk password:

Step 1. Open the UEFI/BIOS setup utility using the administrator password.

Step 2. Select Security → Set Hard Disk Password and press Enter.

Step 3. Follow on-screen instructions to set both master and user hard disk passwords. They must be set at the same time.

Step 4. Select Exit → Exit Saving Changes.

Change or remove hard disk password:

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security.

Step 3. To change or remove the master password, select Change Master Password and press Enter. (Note: If you remove the master hard disk password, the user hard disk password is also removed).

Step 4. To change the user hard disk password, select Change User Password and press Enter. (Note: The user hard disk password cannot be removed separately).

Step 5. Select Exit → Exit Saving Changes.

Press and hold the power button until the computer turns off. Then restart the computer.

1. Carefully unplug the ac power adapter and turn off the computer immediately. The more quickly you stop the current from passing through the computer the more likely you will reduce damage from short circuits.

Attention: Although you might lose some data or work by turning off the computer immediately, leaving the computer on might make your computer unusable.

2. Wait until you are certain that all the liquid is dry before turning on your computer.

CAUTION: Do not try to drain out the liquid by turning over the computer. If your computer has keyboard drainage holes on the bottom, the liquid will be drained out through the holes.

You can get the latest device drivers and UEFI/BIOS from:

Lenovo Vantage or Lenovo PC Manager

Your LENOVO LEGION PRO 5 16IRX10 D1 may have Flip to Start enabled. Many Lenovo notebook computers include a sensor that can detect the angle at which the lid is opened. When you open the lid, the sensor can detect this behavior. If Flip to Start is enabled, the computer will respond by starting up automatically.

If you don’t like this feature, you can disable it. Flip to Start can be enabled and disabled in:

Lenovo Vantage or Lenovo PC Manager

Firmware Setup Utility

Your Windows operating system version is not up to date and does not include the necessary software components. Update your Windows operating system to version 23H2 or later using Windows Update and then try again.

Note: The Version 23H2 update may not be immediately available for your PC. You may need to periodically open Windows Update and manually check for updates to install the 23H2 update when it becomes available for your PC.

Customer Replaceable Units (CRUs) are parts that can be replaced by the customer. A LENOVO LEGION PRO 5 16IRX10 D1 may contain the following types of CRUs:

Self-service CRU: Parts that can be replaced easily by customers themselves or by trained service technicians at an additional cost.

Optional-service CRU: Parts that can be replaced by customers with a greater skill level. Trained service technicians can also provide service to replace the parts under the type of warranty designated for the customer’s machine.

The table below lists the CRUs and CRU types that are defined for your product model.

Lenovo keyboards are designed with accessibility in mind, including:

keyboard layout: The alphabetic keys are arranged in a QWERTY layout. The F and J keys have bumps that make them tactilely distinguishable, serving as an orientation aid for skilled typists. Some keyboards include a separate numeric keypad where the 5 key features a bump to make it tactilely distinguishable.

Standard modifier keys: Keyboards are equipped with standard modifier keys for PCs, including the alt key, the ctrl key, the shift key, and the Windows logo key.

The tab key: Located in the leftmost column, users can press the tab key and alt + tab (in reverse order) to cycle through interactive elements.

Hotkeys: Many keyboards feature hotkeys in the top row, offering convenient access to frequently used settings.

The fn key and the fnlock: The fn key is a Lenovo-defined modifier key. It can be used with dual-function keys or other keys to access specific settings. The fnlock (fn + esc) is a switch that allows users to access both hotkey and function key functionalities without the need to press two keys simultaneously.

Keyboard backlight: Many keyboards are equipped with backlights to help use the keyboard in dark lighting conditions, controlled by pressing fn + Space.

Windows 11 provides a centralized location within the Settings app for activating and configuring all accessibility features. You can access this section by selecting Start → Settings → Accessibility. Additionally, the keyboard shortcut Windows logo key + U provides quick access to this interface.

Narrator is Windows 11’s built-in screen-reading application. It can read screen content aloud to users and also accept input from the keyboard.

Start and stop Narrator: You can start and stop Narrator by selecting the toggle button for Narrator in the centralized Accessibility section of the Settings app. Additionally, the keyboard shortcut Windows logo key + ctrl + enter provides quick access to both the start and stop functions.

Customize Narrator: All Narrator settings are conveniently located in the centralized Accessibility section of the Settings app. You can install additional text-to-speech voices, select your preferred voice, and adjust the verbosity level. The keyboard shortcut Windows logo key + ctrl + N offers quick access to these settings.

For individuals who find it difficult to see text clearly on the screen, Windows offers several options:

Adjust text sizes:

Step 1. Select Start → Settings → Accessibility → Text size.

Step 2. Use the slider and the preview pane to select a size that fits your need and then select Apply.

Apply a high-contrast theme:

Step 1. Select Start → Settings → Accessibility → Contrast themes.

Step 2. In the dropdown list for Contrast themes, select one option and then select Apply.

To exit a contrast theme, select None from the dropdown list. The keyboard shortcut for turning on and off contrast theme is left alt + left shift + prt sc.

Enable Magnifier:

Step 1. Select Start → Settings → Accessibility → Magnifier.

Step 2. Select the toggle to enable or disable Magnifier.

The keyboard shortcuts for enabling and disabling Magnifier are Windows logo key + Plus sign (+) and Windows logo key + esc, respectively. When Magnifier is enabled, you can use Windows logo key + plus sign (+) and minus sign (-) to zoom in and zoom out.

Sticky Keys is an accessibility feature in Windows that, when enabled, allows users to press keys in sequence to activate shortcut functions, rather than holding them down simultaneously. For example, instead of holding down the ctrl key and the C key, users can press each key individually to copy text.

To enable Sticky Keys, press the shift key five times in quick succession. When the confirmation dialog box appears, select Yes. To disable Sticky Keys, press the shift key five times again and choose No when prompted.