FREE ENGLISH LELO IRIS (01) PDF USER GUIDE

FREE ENGLISH LELO IRIS (01) PDF USER MANUAL

FREE ENGLISH LELO IRIS (01) PDF OWNER GUIDE

FREE ENGLISH LELO IRIS (01) PDF OWNER MANUAL

FREE ENGLISH LELO IRIS (01) PDF REFERENCE GUIDE

FREE ENGLISH LELO IRIS (01) PDF INSTRUCTION GUIDE

FREE ENGLISH LELO IRIS (01) PDF REFERENCE MANUAL

FREE ENGLISH LELO IRIS (01) PDF INSTRUCTION MANUAL

FREE ENGLISH LELO IRIS (01) PDF OPERATING INSTRUCTIONS


CLICK HERE TO DOWNLOAD LELO IRIS (01) PDF MANUAL

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How do I charge the ELISE / IRIS?

Before charging, ensure the DC socket is free from water or lubricant residue. Blowing into the socket can help remove water.

  1. Gently remove the protective silicone cap on the back of your ELISE / IRIS.
  2. Gently insert the DC plug into the DC socket until you feel a subtle click.
  3. Insert the mains plug into the wall socket.

The LED will pulse to indicate charging. When fully charged (after approximately 3 hours), the LED will emit a steady glow.

Important Charging Notes:

  • Do NOT use your ELISE / IRIS while it is charging.
  • Do NOT charge for more than 24 hours continuously.
  • Only use the original chargers provided by LELO.

How do I know if the battery is running low?

If the battery is running low, the LED indicator will emit a red glow (instead of white) when the interface dial is pushed, prompting you to charge the device.

How do I turn the ELISE / IRIS on and adjust vibration intensity?

  1. Hold down the ‘+’ quadrant of the interface dial to activate your ELISE / IRIS.
  2. Continue pressing the ‘+’ quadrant to increase the vibration intensity until you reach the desired level.
  3. Press the ‘-‘ quadrant to decrease the vibration intensity.

When any quadrant of the dial is pressed, the LED indicates that the interface is active.


How do I turn the ELISE / IRIS off?

To turn off your ELISE / IRIS, hold down the ‘-‘ quadrant of the interface dial. The vibration intensity will decrease until the device is completely off.

How do I lock and unlock the ELISE / IRIS interface dial?

To prevent accidental activation, especially during transport, you should lock the interface dial.

  • To lock: Hold down the complete interface dial (all quadrants) for five seconds. The LED will light up and then go dark, indicating ELISE / IRIS is locked.
  • To unlock: Repeat the process – hold down the complete interface dial for five seconds until the LED lights up.

Note: Charging the device will automatically unlock the ELISE / IRIS.


How do I use the stimulation modes on the ELISE / IRIS?

Your ELISE / IRIS has five programmed stimulation modes utilizing the individually powered base and crown pleasure points.

When you first turn the ELISE / IRIS on, it starts in mode 1 (crown continuous vibration).

Press the ▲ or ▼ quadrants of the interface dial to cycle through the modes.

The modes are:

Mode Pleasure Point Characteristics
1 crown continuous vibration – tip of stem
2 base continuous vibration – base of stem
3 crown & base short interval pulsation
4 crown & base extended interval pulsation
5 crown & base continuous vibration – full stem

How should I clean the ELISE / IRIS?

Always clean your ELISE / IRIS thoroughly before and after each use.

  1. Wash the stem with warm water and antibacterial soap.
  2. Rinse with clean hot water.
  3. Pat dry with a lint-free cloth or towel.

Important Cleaning Notes:

  • Avoid submerging the device and getting water into the DC socket or around the interface dial.
  • Never use cleansers containing alcohol, petrol, or acetone.

What kind of lubricant should I use with the ELISE / IRIS?

  • LELO recommends using a water-based lubricant as the safest option.
  • Do NOT use silicone-based lubricants, as they could make the device’s silicone permanently tacky. If you wish to try a silicone-based lubricant, perform a patch test first.
  • Never use massage oil or hand cream as lubricants.

How should I store the ELISE / IRIS?

  • Store your ELISE / IRIS in a dust-free place.
  • Keep her away from toys made of other materials.
  • Avoid leaving your ELISE / IRIS in direct sunlight.
  • NEVER expose her to extreme heat.

What should I do if the LED does not pulse when the charger is connected?

There are a few possibilities:
  • The battery may be fully charged. A full charge provides up to 4 hours of use.
  • The battery may be completely drained and will require several minutes connected to the charger to acknowledge it.
  • The charger might not be properly connected. Check the connection at the wall socket and the DC socket on the device.

Why doesn’t the ELISE / IRIS activate when I press the ‘+’ quadrant?

There are two main reasons this could happen:
  • The battery is empty. Recharge your ELISE / IRIS.
  • The interface dial is locked. Unlock it by holding down the whole interface dial for 5 seconds until the LED lights up.

What if the ELISE / IRIS cannot be switched off or the interface dial doesn’t respond?

The microprocessor may be temporarily malfunctioning. Connect the charger to the device; this should restore the function to normal.

What are the specifications of the ELISE / IRIS?

MATERIALSPC-ABS / body safe silicone
FINISHglossy / pearl
SIZE220 x 42 x 36 mm
WEIGHT170 grams
BATTERYLi-Ion 900 mAh 3.7 V
CHARGING3 hours at 4.8 V 300 mA
USER TIMEup to 4 hours
STANDBYup to 90 days
FREQUENCY120 Hz
MAX. NOISE LEVEL< 50 dB
INTERFACEvariable interface dial, 5 modes

Who should I contact if I have other problems or questions?

If you experience any other problems with your ELISE / IRIS or if you have any questions regarding its operation, please contact LELO Customer Care at: CUSTOMERCARE@LELO.COM

CLICK HERE TO DOWNLOAD LELO IRIS (01) PDF MANUAL


Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.