LECTRIC XP 3.0 (01) PDF Document

Before and after each ride on your LECTRIC XP 3.0, it is recommended to go through the following safety checklist:

☑ Before each ride, inspect your eBike for damage. If damage is found, do not ride.

☑ Verify that the front and rear axles are secure.

☑ Check that the front and rear tire pressure is within the recommended pressure range printed on the tire sidewall.

☑ Pull the brake levers to ensure the brakes are working properly and adjust if necessary.

☑ Visually inspect the bike for damage or anything out of the ordinary.

☑ Turn on the lights, especially if riding at night.

☑ Make sure all hardware is tightened to the recommended torque specifications.

☑ Verify that the frame folding latch is securely closed and locked.

☑ Verify that the stem folding latch is securely closed and locked.

☑ Check that the handlebar stem is inserted past the minimum insertion point. The minimum insertion point is labeled near the bottom of the handlebar stem.

☑ Check that the handlebar stem collar and clamp are closed and tightened to 6 Nm or till it leaves an impression on your hand.

☑ Check that the seatpost is inserted past the minimum insertion point. The minimum insertion point is labeled on the seatpost.

☑ Check that the seatpost collar and clamp are closed and tightened to 18 Nm or till it leaves an impression on your hand.

☑ Check that the seat cannot be twisted out of position, and set the height to a safe position that makes it easy to mount and dismount the bike.

☑ Make sure the pedals are locked in a flat position.

☑ Check the condition of the chain to see if it needs cleaning or lubrication.

☑ Wear a helmet and high visibility clothing.

☑ NEVER exceed the maximum total weight limit of 330 lbs. (150 kg). The rear rack can hold a maximum of 150 lbs. (68 kg). As an example, if you have 40 lbs. (18 kg) of cargo, then the maximum weight of the rider would be 290 lbs. (131 kg).

☑ Only carry the cargo you need. More weight will drain the battery faster and affect how the bike handles.

☑ Ensure all components are properly secured.

☑ Make sure your battery is fully charged.

Riding your LECTRIC XP 3.0 at night comes with more risks than riding during the day due to decreased visibility. Riders are encouraged to exercise increased caution in nighttime conditions.

• Turn lights ON for safety. For increased visibility, ensure that the front headlight and rear taillight are turned ON and adjusted such that other people on the road can see them clearly. Also check your front and rear wheel reflectors.

• Riders should wear reflective clothing at night. You may want to attach additional flashing lights to your clothing or helmet.

To unfold the stem:

1. Begin with handlebars in the folded position.

2. Pull the handlebar stem to its upright position.

3. Push the latch in firmly until it locks in position.

4. Pull on the latch to confirm it is locked and the handlebars cannot fold.

To fold the stem:

1. Pull up on the silver button labeled “open” to unlock the latch.

2. Pull the latch away from the stem while still holding the “open” button.

3. Fold the stem by lowering it to the side.

To unfold the frame:

1. To unfold the bike frame, stand near the frame where the battery is exposed. Grab the stem and rear end of the bike. Lift the bike slightly off the ground and swing to the closed position.

2. Push down the latch firmly until it locks into position. Pull on the latch to confirm that the latch has locked and that the frame cannot fold.

To fold the frame:

1. To unlock the bike frame and return it to the folded position, start by sliding the switch labeled “open” to the right.

2. Pull the latch while still holding the switch to the “open” position. You may now fold the bike.

To unfold the pedals:

1. Pull each pedal out until you hear an audible click as they lock into position.

To fold the pedals:

1. Grasp pedal and push lightly toward bicycle.

2. Continue pushing while raising pedal into its folded position.

3. The pedal will click into the folded position.

To adjust the handlebars on your LECTRIC XP 3.0, select a height that is comfortable for you. DO NOT extend past the minimum insertion point marked on the stem. To adjust your handlebars, unlatch the clamp. Move the handlebars to the desired height and close the clamp. Re-tighten the stem clamp to the recommended torque (10 Nm).

To achieve the correct seat height for your LECTRIC XP 3.0:

1. Sit on the seat.

2. Place one heel on a pedal.

3. Rotate the crank until the pedal with your heel on it is in the down position and the crank arm is parallel to the seat tube.

If your leg is not completely straight, your seat height needs to be adjusted. If your hips must rock for your heel to reach the pedal, the seat is too high. If your leg is bent at the knee with your heel on the pedal, the seat is too low.

To adjust the seat height:

1. Loosen the seatpost clamp.

2. Raise or lower the seat post in the seat tube. ALWAYS insert the seat post past the minimum insertion point marked on it.

3. Check that the seat is straight before and after.

4. Re-tighten the seat post clamp to the recommended torque (18 Nm).

Front and back adjustment: Loosen nuts on both sides of the seat. Make sure the clamp mechanism is clamping on the straight part of the seat rails and is not touching the curved part of the rails. Ensure that you are using the recommended torque on the clamping fastener(s) (20 Nm).

Seat angle adjustment: Most people prefer a horizontal seat; but you may prefer the seat nose angled slightly up or down. Loosen the clamp bolt to allow any serrations on the clamp mechanism to disengage before changing the seat angle, and to fully re-engage the serrations before you tighten the clamp bolt to the recommended torque (20 Nm).

Your LECTRIC XP 3.0 comes with a 7-speed freewheel. While pedaling in 1st gear (lowest gear using the largest sprocket), it will be easier to pedal up hills. In 7th gear (highest gear using the smallest sprocket), it will be easier to reach higher speeds on flat or downhill terrain.

To shift up: Press the lower button marked with the plus (+) sign.

To shift down: Push the upper lever marked with the minus (-) away from you.

The right handlebar on your LECTRIC XP 3.0 features a half-twist throttle.

To operate: Check that the Pedal Assist (PAS) level is set above 0, then twist the throttle back slowly to achieve your desired speed and acceleration.

Your LECTRIC XP 3.0 is equipped with mechanical disc brakes. ALWAYS apply the right brake lever (rear wheel) before and during use of the front brake. ALWAYS apply even pressure to both brake levers when slowing down or stopping.

To brake the rear wheel: Pull right brake lever to activate rear brake.

To brake the front wheel: Pull left brake lever to activate front brake.

The suspension fork on your LECTRIC XP 3.0 will affect the handling of the bicycle, primarily when going over bumps and stopping. You can adjust its stiffness for the terrain and your weight.

To increase stiffness: Turn the black knob clockwise towards the “lock” direction indicated.

To reduce stiffness: Turn the black knob counterclockwise towards the “open” direction indicated.

To fully lock suspension: Turn the black knob clockwise towards the “lock” direction indicated until it cannot be turned further.

To turn lights ON: Hold the plus (+) button on the display control pad for about 3 seconds until the lights turn ON.

To turn lights OFF: Hold the plus (+) button on the display control pad for about 3 seconds until the lights turn OFF.

To get the maximum range out of each battery charge on your LECTRIC XP 3.0, there are some simple things you can do:

• Ride at a lower PAS level

• Use lower PAS levels and pedal when climbing hills

• Pedal when starting from a standstill

The display on your LECTRIC XP 3.0 shows the following information:

1. Walk Mode, Cruise Control, and Pedal assist (PAS) Level Indicator: Shows if these modes are active and the current PAS level.

2. Odometer, Trip A, Voltage, Current, Trip Timer (TM) readouts: Displays various ride metrics.

3. Battery level indicator bar: Shows the estimated remaining battery charge.

4. Maximum and Average Speed: Displays your max and average speed for the current trip.

5. Speedometer in MPH or KM/H: Shows your current speed.

6. Light On/Off Indicator: Shows if the lights are on.

7. Mile and kilometer indicators: Indicates the unit of distance used.

NOTE: The trip meter, as well as maximum and average speed will reset when the bicycle is powered OFF.

To change display settings, hold the plus (+) and the minus (-) buttons simultaneously to enter into the Settings Menu. Press the POWER button to toggle between each numbered setting. To adjust the value of each setting, click the plus (+) and the minus (-) buttons as needed.

You should only change the settings listed below:

Before increasing your LECTRIC XP 3.0’s top speed, ALWAYS check your local laws and regulations to determine if it is lawful to ride Class 3 eBikes on public roads. If you increase your bicycle’s top speed, you must remove the Class 2 label and reveal the Class 3 label located underneath it.

To increase maximum speed:

1. Press and hold the plus (+) and minus (-) buttons on the control pad simultaneously until the screen says “P1”.

2. Press the POWER button on the control pad to cycle through the settings.

3. Go to setting “P08” and change this value from 32 to 100.

NOTE: This setting represents the top speed in kilometers per hour. For Class 2 performance, this speed setting must not exceed 20 mph (32 km/h). For Class 3 performance, this setting will be set at 100, indicating the bike has been completely unlocked to enable speeds of up to 28mph. Please note: The maximum achievable top speed will vary by tire inflation pressure, road conditions, total payload, battery charge level and other factors.

4. Press and hold the plus (+) and the minus (-) buttons on the control pad to exit Settings Menu.

5. Power bicycle OFF by holding the POWER button to save the settings.

Passenger Mode on your LECTRIC XP 3.0 is designed to add an additional level of protection when a passenger is on the bike. Passenger Mode will limit the top speed to 10mph.

To engage Lectric “Passenger Mode”:

1. Press and hold the (-) and POWER buttons on the control pad simultaneously for 5 seconds until the screen flashes PAS and speedometer.

2. Check setting has been activated by riding without passenger and speed has been limited to 10mph.

To disengage:

1. Turn your Lectric XP OFF and then ON. Or change your P08 setting to 32 or 100 and Passenger Mode will deactivate.

Your LECTRIC XP 3.0 is equipped with Walk Mode to make walking the heavier bicycle easier. Walk Mode can be toggled on or off in the settings menu (P21).

To activate:

Hold down the minus (-) button on the display control pad and the motor will engage at a speed similar to a slow walk. When Walk Mode is active, “Walking” will appear on the display. ALWAYS keep wheels in contact with the ground when using Walk Mode.

To deactivate:

Pull either brake lever to disengage Walk Mode OR press and hold the minus (-) button on the display control pad.

Cruise control on your LECTRIC XP 3.0 works similarly to cruise control on a car. The bike will try to maintain a speed based on the position of the throttle when cruise control was activated.

To activate:

Hold the minus (-) button while twisting the throttle. When Cruise Control is active, “Cruise” will appear on the display.

To deactivate:

Pull either brake lever to disengage Cruise Control.

When carrying a passenger on your LECTRIC XP 3.0, adhere to the following weight limits and guidelines:

• Bike total maximum payload: 330 lbs (150 kg)

• Rear cargo rack maximum payload: 150 lbs (68 kg)

• Foot pegs: 39 lbs (18 kg) per side

Safety Guidelines:

• A passenger incapable of riding a bike on their own should not ride as a passenger.

• When carrying a passenger, you must have the foot pegs, and the seat appropriate for the rider, and the rear fender is recommended.

• Follow the stated weight limits for the bike and accessories; do not overload.

• Ensure that both the rider and passenger are wearing a properly fitted and approved helmet.

• Hold onto the bike when loading cargo and/or passengers. Ensure passenger sits over or forward of the rear wheel.

• Do not allow passengers to sit sideways or backward on the rear cargo rack.

• Do not allow passengers to stand or kneel on the rear cargo rack or foot pegs.

• Ensure that passengers are safely seated before beginning to ride.

• A passenger should sit on the rear passenger seat directly over or forward of the rear wheel axle, hold onto the passenger handlebars, rider’s hips, or waist (but not shoulders), and keep their feet on the foot pegs when the bike is in motion.

• Instruct passengers to brace for bumps and be prepared for turns, braking, and other maneuvers.

Before your first ride, you should use the lowest level of pedal assist (PAS 1) and become familiar with the operation of your LECTRIC XP 3.0 in a safe environment.

To start:

1. Insert key and turn counterclockwise to the ON position. The key will be parallel with the frame. The keys must remain in the bike to use.

2. Hold down the POWER button located on the left handlebar until the display comes on.

3. Select a Pedal Assist (PAS) level using the plus (+) and minus (-) buttons. PAS 0 provides no motor assist. PAS 1 is the lowest level of assist and PAS 5 is the highest level of assist.

To end your ride:

When the bicycle is at a complete stop, press and hold the POWER button to turn the display OFF. This ensures the motor will not activate until the display is turned ON again and you are ready to ride.

To prevent serious injury or death, follow these battery safety guidelines for your LECTRIC XP 3.0:

• Only use original Lectric eBike batteries for your eBike.

• Do not leave your battery unattended while charging.

• When removing the battery, unplug the rubber stopper on the charging point.

• Always charge your battery in temperatures between 32°F – 113°F (0°C – 45°C).

• For an optimum service life, operate your Lectric eBike battery at temperatures between 32° F -104° F (0°C-40°C).

• Avoid contact with skin and eyes if battery leakage occurs. If contact happens, wash with soap and water and seek medical attention if it contacts eyes.

• Always remove the battery from the bicycle when not in use and store in a secure location.

• Do not submerge the battery in liquid of any kind.

• Turn display OFF when not in use and before removing battery pack.

• Do not puncture, crush, impact, or modify the battery pack in any way.

• Protect the battery pack from heat (e.g., temperature >140°F), fire, and immersion in water.

• Do not open the battery. There is a risk of short circuiting.

• When the battery is not in use, keep it away from small metal objects that could make a connection from one terminal to another.

• Do not place the charger or the battery near flammable materials.

• Use the battery only in conjunction with your Lectric eBike.

• Keep the battery away from children.

• Always remove the key from the battery pack after each use.

You can charge the battery for your LECTRIC XP 3.0 while it is in or out of the bicycle. Locate the charge port on the side of the battery.

1. Plug the cable from the charger into the port on the side of the battery pack.

2. Plug the charger power cable into an electrical mains wall socket.

Charging Information:

• Do not leave your battery unattended while charging.

• Only charge the battery indoors and in dry spaces which are not excessively hot or cold (within 10°F of room temperature).

• The charger light will be red when charging and turn green when finished.

• Charging takes approximately 4-6 hours if the battery is mostly empty.

• The charger may get hot (>165°F) when charging. Use caution.

• Remove the charger from the battery within one hour of the green light indicating a complete charge.

• Never charge a battery for more than 12 hours at a time.

The battery on your LECTRIC XP 3.0 has 3 key positions: UNLOCKED, OFF, and ON. These positions are marked on the battery and can only be seen when the battery is removed from the bike.

To install:

1. Fully insert the battery pack into the bicycle frame with the key removed. The locking pin will be retracted.

2. Insert the key into the battery through the hole in the bottom of the frame (UNLOCKED position). Push the key into the battery and continue pushing until you have twisted the keys to the desired position.

3. Turn the key clockwise to the OFF position. There will be one audible click, and the locking pin will now protrude through the frame. In this position, the battery pack will be secured to the frame, but the power will not be active.

4. Turn the key clockwise again so the key is parallel with the frame (ON position). The key must be in the ON position to turn on the bike.

To uninstall (remove):

To unlock the battery and remove it from the frame, follow the steps listed above in reverse order. Be sure to remove the key from the battery before removing the battery from the bicycle. If the key is still in the battery, it will prevent the battery from being removed from the frame.

When the battery pack for your LECTRIC XP 3.0 will not be used for weeks or months, remove it from the eBike and store the battery pack at about 60% charge as indicated by the Energy Bar on the display. At about 60% charge, the battery will degrade less, compared to higher charge levels.

Every 2-3 months check the battery charge level and recharge to 60%, if necessary.

Storage Conditions:

Always store your Lectric eBike battery pack in a location that:

• Is in a room with a smoke alarm;

• Is away from combustible or easily flammable objects; and

• Is away from heat sources.

Store the battery pack in a dry, well-ventilated place, protected from moisture and water. Operate your battery at temperatures between 32° F – 104° F (0°C – 40°C).

If the charging indicator lights do not illuminate:

1. Check that the cord is connected to the charger.

2. Check power availability at the main plug location.

3. If the battery does not charge, unplug and contact Lectric eBikes. Do not attempt to repair cord or charger.

If the charging indicator light is always red, the battery pack may be defective. Contact Lectric eBikes customer support for assistance.

Storing Your LECTRIC XP 3.0:

Please observe storage temperatures for your Lectric eBike. Protect the Drive Unit, Cockpit System, and Battery Pack against extreme temperatures (e.g. from intense sunlight without adequate ventilation). Extreme temperatures can cause the components (especially the battery) to be damaged.

Transporting Your LECTRIC XP 3.0:

• Always remove the battery pack before transporting your Lectric eBike on a bicycle rack mounted on your vehicle.

• Always use a bicycle rack that is compatible with your Lectric eBike. Check your bicycle rack manual to be sure your rack has sufficient capacity.

• Never attempt to use a roof-mounted bicycle rack. ONLY use hitch-mounted racks.

• Always use proper lifting techniques when lifting your Lectric eBike. Electric bicycles are generally heavier than bicycles.

If your LECTRIC XP 3.0 will not turn ON, try the following solutions:

1. Charge the battery until the light on the charger turns from red to green. This may take up to 8 hours.

2. Insert key in the battery and turn counterclockwise to the ON position, or until the key is parallel with the frame. Then press and hold the POWER button to turn ON.

3. Follow the cable coming from the display down to the quick plug. You may need to unravel some of the plastic wrapping to access it. With a quick pull (do not twist), unplug the quick plug, inspect both sides of the plug, and reconnect by lining up the arrows on both ends. After checking the quick plug, press and hold the POWER button on the display control pad to turn on.

If the pedal assist or throttle do not work on your LECTRIC XP 3.0, try these steps:

1. Check that the PAS level is set between 1-5.

2. To test if PAS is working, do not operate throttle.

3. To test if the throttle is working, do not pedal.

4. Check all quick plugs.

If a fault is detected on your LECTRIC XP 3.0, a corresponding error code will appear on the display. Here are the meanings and common solutions:

100 Mile Tune-Up:

After 100 miles, or 5 full battery charge cycles, have the following services performed at a bicycle shop:

• Brake cables may need to be adjusted and tensioned properly.

• Shifting cables will stretch during the wear-in period. The derailleur may need to be adjusted.

• All hardware should be adjusted to the specified Tightening Torque. If any hardware is damaged, it may need to be replaced by a bicycle mechanic.

Monthly (or about every 250-500 miles):

• Inflate tires to pressure within recommended range printed on tire sidewalls.

• Lubricate chain.

• Check that all hardware is tightened to the torque specifications.

• Check your brake pads for signs of wear. Replace if necessary.

• Check your bicycle’s shifting performance. Adjust the derailleur if necessary.

• Clean the bicycle with low residue cleaner and dry completely. Lubricate after cleaning where necessary.

• Check spoke tension and adjust if necessary.

Quarterly (or about every 750-1500 miles):

• Check all items on the monthly service list above.

• Check tire tread for excessive wear. Replace if necessary.

• Check electrical connectors and cable housings are secured away from moving parts and are free from damage. Replace if necessary.

To clean your LECTRIC XP 3.0, do not submerge it or its components in water, or use a pressure washer. Clean your eBike carefully with a soft, damp cloth (using only mild soap and water). Rinse with water. The electrical components on your Lectric eBike are IP 65 rated.