LECTRIC XP STEP-THRU 3.0 (01) PDF Document

The intended use of your LECTRIC XP STEP-THRU 3.0 is to be ridden by one adult rider (age 16 and up) at an appropriate time and place for general transportation and/or recreational use. Any other use is prohibited. The bicycle is NOT INTENDED for off-road or mountain bicycle use, or for any kind of jumping. Riders should be proficient cyclists (ages 16+), riding on paved surfaces where the tires are always on the ground, on roadways, or dedicated bicycle-only lanes where permitted by law. Your bicycle should not be used to tow another bicycle.

Before and after each ride on your LECTRIC XP STEP-THRU 3.0, you should perform the following safety checks:

☐ Before each ride, inspect your eBike for damage. If damage is found, do not ride.

☐ Verify that the front and rear axles are secure.

☐ Check that the front and rear tire pressure is within the recommended pressure range printed on the tire sidewall.

☐ Pull the brake levers to ensure the brakes are working properly and adjust if necessary.

☐ Visually inspect the bike for damage or anything out of the ordinary.

☐ Turn on the lights, especially if riding at night.

☐ Make sure all hardware is tightened to the recommended torque specifications.

☐ Verify that the frame folding latch is securely closed and locked.

☐ Verify that the stem folding latch is securely closed and locked.

☐ Check that the handlebar stem is inserted past the minimum insertion point. The minimum insertion point is labeled near the bottom of the handlebar stem.

☐ Check that the handlebar stem collar and clamp are closed and tightened to 6 Nm or till it leaves an impression on your hand.

☐ Check that the seatpost is inserted past the minimum insertion point. The minimum insertion point is labeled on the seatpost.

☐ Check that the seatpost collar and clamp are closed and tightened to 18 Nm or till it leaves an impression on your hand.

☐ Check that the seat cannot be twisted out of position, and set the height to a safe position that makes it easy to mount and dismount the bike.

☐ Make sure the pedals are locked in a flat position.

☐ Check the condition of the chain to see if it needs cleaning or lubrication.

☐ Wear a helmet and high visibility clothing.

☐ NEVER exceed the maximum total weight limit of 330 lbs. (150 kg). The rear rack can hold a maximum of 150 lbs. (68 kg). As an example, if you have 40 lbs. (18 kg) of cargo, then the maximum weight of the rider would be 290 lbs. (131 kg).

☐ Only carry the cargo you need. More weight will drain the battery faster and affect how the bike handles.

☐ Ensure all components are properly secured.

☐ Make sure your battery is fully charged.

When riding your LECTRIC XP STEP-THRU 3.0 in wet conditions, please follow these precautions:

• Use caution as it will take longer to brake and to stop. Your tires may slip when turning. The risk of a crash is dramatically increased in wet conditions.

• Your electric bicycle can withstand light rain and small splashes, but it is not designed to be subjected to inclement weather, extremely heavy showers, or submersion in water. The electric bike’s components have an IP rating of 65. Water damage is not covered under the warranty.

Riding at night comes with more risks than riding during the day due to decreased visibility. Riders are encouraged to exercise increased caution in nighttime conditions.

• Turn lights ON for safety. For increased visibility, ensure that the front headlight and rear taillight are turned ON and adjusted such that other people on the road can see them clearly. Also check your front and rear wheel reflectors.

• Riders should wear reflective clothing at night. You may want to attach additional flashing lights to your clothing or helmet.

States that recognize three classes of eBikes require a label to be placed on the bicycle denoting its class, motor wattage, and top speed. Your LECTRIC XP STEP-THRU 3.0 comes as a Class 2 bicycle by default and has a label with this information posted under the carry handle, near the seat post.

• Class 2 eBike: 500W, Top Speed: 20mph

• Class 3 eBike: 500W, Top Speed: 28mph

If you change your bicycle’s top speed, you must remove the Class 2 label from the bicycle and replace it with a Class 3 label, detailing your eBike’s class, top pedal-assisted speed, and motor wattage. The Class 3 label is located directly under the Class 2 label.

When you unbox your LECTRIC XP STEP-THRU 3.0, you should find the following items:

• Lectric XP eBike

• Lectric XP eBike Charger

• 2 Battery Keys

Your serial number is located on the head tube of the LECTRIC XP STEP-THRU 3.0 bicycle. It is recommended to write it down for your records in case it is needed for a warranty request or if the bicycle is stolen.

To unfold the stem:

1. Begin with handlebars in the folded position.

2. Pull the handlebar stem to its upright position.

3. Push the latch in firmly until it locks in position.

4. Pull on the latch to confirm it is locked and the handlebars cannot fold.

To fold the stem:

1. Pull up on the silver button labeled “open” to unlock the latch.

2. Pull the latch away from the stem while still holding the “open” button.

3. Fold the stem by lowering it to the side.

To unfold the frame:

1. To unfold the bike frame, stand near the frame where the battery is exposed. Grab the stem and rear end of the bike. Lift the bike slightly off the ground and swing to the closed position.

2. Push down the latch firmly until it locks into position. Pull on the latch to confirm that the latch has locked and that the frame cannot fold.

To fold the frame:

1. To unlock the bike frame and return it to the folded position, start by sliding the switch labeled “open” to the right.

2. Pull the latch while still holding the switch to the “open” position. You may now fold the bike.

To unfold the pedals:

1. Pull each pedal out until you hear an audible click as they lock into position.

To fold the pedals:

1. Grasp pedal and push lightly toward the bicycle.

2. Continue pushing while raising the pedal into its folded position.

3. The pedal will click into the folded position.

To adjust the handlebars on your LECTRIC XP STEP-THRU 3.0, select a height that is comfortable for you. DO NOT extend past the minimum insertion point marked on the stem. To adjust, unlatch the clamp, move the handlebars to the desired height, and close the clamp. Re-tighten the stem clamp to the recommended torque of 10 Nm. A stem that is positioned too high can damage the bike and can cause you to lose control and crash.

Proper seat adjustment is important for performance and comfort. ALWAYS insert the seat post past the minimum insertion point marked on it.

To achieve the correct seat height:

1. Sit on the seat.

2. Place one heel on a pedal.

3. Rotate the crank until the pedal with your heel on it is in the down position and the crank arm is parallel to the seat tube.

Your leg should be almost completely straight. If your hips must rock for your heel to reach the pedal, the seat is too high. If your leg is bent at the knee, the seat is too low.

To adjust seat height:

1. Loosen the seatpost clamp.

2. Raise or lower the seat post in the seat tube.

3. Check that the seat is straight.

4. Re-tighten the seat post clamp to the recommended torque (18 Nm).

To adjust seat position (front/back and angle):

• Front and back adjustment: Loosen the nuts on both sides of the seat. Ensure the clamp is on the straight part of the seat rails. Tighten to the recommended torque (20 Nm).

• Seat angle adjustment: Loosen the clamp bolt to disengage any serrations, adjust the seat nose angle, then fully re-engage the serrations and tighten the clamp bolt to the recommended torque (20 Nm).

Your LECTRIC XP STEP-THRU 3.0 comes with a 7-speed freewheel. While pedaling in 1st gear (lowest gear, largest sprocket), it is easier to pedal up hills. In 7th gear (highest gear, smallest sprocket), it is easier to reach higher speeds on flat or downhill terrain.

• To shift up (to a higher gear, e.g., from 3 to 4): Press the lower button marked with the plus (+) sign.

• To shift down (to a lower gear, e.g., from 4 to 3): Push the upper lever marked with the minus (-) away from you.

The right handlebar of your LECTRIC XP STEP-THRU 3.0 features a half-twist throttle. To operate it, check that the Pedal Assist (PAS) level is set above 0, then twist the throttle back slowly to achieve your desired speed and acceleration.

To prevent serious injury or death, follow these braking procedures:

• ALWAYS apply the right brake lever (rear wheel) before and during the use of the front brake.

• ALWAYS apply even pressure to both brake levers when slowing down or stopping.

If only the front brake is applied while slowing or stopping quickly, you may be ejected over the front handlebars.

• To brake the rear wheel: Pull the right brake lever.

• To brake the front wheel: Pull the left brake lever.

Be aware that disc brake rotors will become hot during use and will stay hot for a short period after. To prevent burns, do not touch the disc rotor right after use.

The suspension fork affects the handling of the bicycle. You can adjust its stiffness for different terrains.

• To increase stiffness: Turn the black knob clockwise towards the “lock” direction indicated.

• To reduce stiffness: Turn the black knob counterclockwise towards the “open” direction indicated.

• To fully lock suspension: Turn the black knob clockwise towards the “lock” direction indicated until it cannot be turned further, making it fully rigid.

• To turn lights ON: Hold the plus (+) button on the display control pad for about 3 seconds until the lights turn ON.

• To turn lights OFF: Hold the plus (+) button on the display control pad for about 3 seconds until the lights turn OFF.

Pedal Assist (PAS) on your LECTRIC XP STEP-THRU 3.0 functions only when you are pedaling. If you do not pedal, the PAS will not activate. The motor output depends on your pedaling and the PAS level you have set. PAS automatically switches off at the maximum speed set for your eBike (up to 28 mph). When the speed falls below the maximum set speed, PAS automatically becomes available again. You can also use your eBike as a normal bicycle without assistance by switching the power button OFF, or by setting PAS to 0. If the battery needs to be charged, PAS will not function.

The range on a single battery charge can vary significantly. The following are estimates based on test conditions (flat ground, ~180 lbs rider, 20 mph top speed, 10.4 Ah Battery).

To get the maximum range out of each battery charge, you can:

• Ride at a lower PAS level.

• Use lower PAS levels and pedal when climbing hills.

• Pedal when starting from a standstill.

NOTE: The trip meter, as well as maximum and average speed will reset when the bicycle is powered OFF.

To change display settings, hold the plus (+) and the minus (-) buttons simultaneously to enter the Settings Menu. Press the power button to toggle between each numbered setting. To adjust the value of each setting, click the plus (+) and the minus (-) buttons as needed. Only change the settings listed below.

Your LECTRIC XP STEP-THRU 3.0 ships as a Class 2 e-bike with a maximum speed of 20 mph. You can change the top speed by adjusting the settings. ALWAYS check your local laws and regulations before increasing your bicycle’s top speed.

To increase maximum speed:

1. Press and hold the plus (+) and minus (-) buttons on the control pad simultaneously until the screen says “P1”.

2. Press the power button on the control pad to cycle through the settings.

3. Go to setting “P08” and change this value from 32 to 100. (NOTE: This setting is in km/h. 32 is ~20 mph. 100 unlocks speeds up to 28 mph).

4. Press and hold the plus (+) and the minus (-) buttons on the control pad to exit the Settings Menu.

5. Power the bicycle OFF by holding the power button to save the settings.

If you increase your speed to Class 3, you must remove the Class 2 label and reveal the Class 3 label underneath.

Passenger Mode is designed to add protection when a passenger is on the bike by limiting the top speed to 10mph.

To engage Lectric “Passenger Mode”:

1. Press and hold the (-) and power buttons on the control pad simultaneously for 5 seconds until the screen flashes PAS and speedometer.

2. Check that the setting has been activated by riding without a passenger; the speed should be limited to 10mph.

To disengage:

1. Turn your Lectric XP OFF and then ON. Or change your P08 setting to 32 (Class 2) or 100 (Class 3) and Passenger Mode will deactivate.

Walk Mode can be toggled on or off in the P21 setting. It helps make walking the heavier electric bicycle easier.

To activate:

• Hold down the minus (-) button on the display control pad. The motor will engage at a speed similar to a slow walk. “Walking” will appear on the display. ALWAYS keep wheels in contact with the ground when using Walk Mode.

To deactivate:

• Pull either brake lever OR press and hold the minus (-) button on the display control pad.

Cruise control will try to maintain a speed based on the position of the throttle when it was activated.

To activate:

• Hold the minus (-) button while twisting the throttle. For low speeds, only slightly twist the throttle while holding the minus (-) button. “Cruise” will appear on the display.

To deactivate:

• Pull either brake lever to disengage Cruise Control.

Before carrying a passenger, check all local regulations to ensure it is allowed. The following weight limits and rules apply:

• Bike total maximum payload: 330 lbs (150 kg)

• Rear cargo rack maximum payload: 150 lbs (68 kg)

• Foot pegs: 39 lbs (18 kg) per side

Important rules for carrying a passenger:

• A passenger incapable of riding a bike on their own should not ride as a passenger.

• When carrying a passenger, you must have foot pegs, and the appropriate seat for the rider.

• Do not overload the bike or its accessories.

• Increased weight will increase braking distance. Plan stops accordingly.

• Both rider and passenger must wear a properly fitted and approved helmet.

• Always hold onto the bike when loading passengers. The kickstand is not for loading.

• Do not allow passengers to sit sideways, backward, stand, or kneel on the rear rack or foot pegs.

• A passenger should sit directly over or forward of the rear wheel axle, hold onto the passenger handlebars, rider’s hips, or waist (not shoulders), and keep their feet on the foot pegs when the bike is in motion.

The acceleration of your eBike may feel faster than anticipated. Before your first ride, use the lowest level of pedal assist (PAS 1) and practice in a safe environment away from obstacles and people.

To start your ride:

1. Insert the key and turn it counterclockwise to the ON position. The key will be parallel with the frame and must remain in the bike to use.

2. Hold down the power button on the left handlebar until the display comes on.

3. Select a Pedal Assist (PAS) level using the plus (+) and minus (-) buttons. PAS 0 provides no motor assist. PAS 1 is the lowest level of assist and PAS 5 is the highest.

IMPORTANT: ALWAYS be seated on the bicycle and engage at least one brake before starting to pedal. The Pedal Assist may activate as soon as you step on the pedals.

To end your ride:

• When the bicycle is at a complete stop, press and hold the power button to turn the display OFF. This ensures the motor will not activate until the display is turned ON again.

To charge your battery, locate the charge port on the side of the battery pack. You can charge the battery while it is in or out of the bicycle.

1. Plug the cable from the charger into the port on the side of the battery pack.

2. Plug the charger power cable into an electrical mains wall socket.

The light on the charger will be red when the battery is charging and will turn green when charging is finished. Charging typically takes 4-6 hours if the battery is mostly empty. After charging is complete, disconnect the charger from the battery and the wall socket. If you charged the battery in the frame, carefully insert the rubber plug into the port to prevent dirt or water ingress.

The battery key has 3 positions: UNLOCKED, OFF, and ON. These are marked on the battery and are visible when it is removed from the bike.

To install:

1. With the key removed, fully insert the battery pack into the bicycle frame. The locking pin will be retracted.

2. From the bottom of the bike, insert the key into the battery through the hole in the frame. The key position will be UNLOCKED.

3. Push the key into the battery and turn it clockwise. You will hear one audible click, and the locking pin will protrude through the frame. This is the OFF position. The battery is secured but the power is not active.

4. Turn the key clockwise again so the key is parallel with the frame. This is the ON position, which is required to turn on the bike.

To uninstall:

• Follow the steps above in reverse order. Be sure to remove the key from the battery before removing the battery from the bicycle. When unlocking and removing the battery, take care that it does not slide out while the bicycle is folded.

When the battery pack will not be used for weeks or months, remove it from the eBike and store it at about 60% charge as indicated by the Energy Bar on the display. At 60% charge, the battery will degrade less.

• Every 2-3 months, check the battery charge level and recharge to 60% if necessary.

• Leaving the battery installed on the bicycle for long-term storage is not recommended.

Always store your battery pack in a location that:

• Is in a room with a smoke alarm.

• Is away from combustible or easily flammable objects.

• Is away from heat sources.

• Is dry and well-ventilated, protected from moisture and water.

Operate and store the battery at temperatures between 32° F -104° F (0°C-40°C). Do not leave the battery in a car during the summer or in direct sunlight.

To prevent serious injury or death while transporting your eBike:

• Always remove the battery pack before transporting your LECTRIC XP STEP-THRU 3.0 on a bicycle rack mounted on your vehicle.

• Always use a bicycle rack that is compatible with your eBike and has sufficient weight capacity. Overloading a rack could cause it to fail.

• Never attempt to use a roof-mounted bicycle rack. ONLY use hitch-mounted racks.

• Always use proper lifting techniques. Electric bicycles are generally heavier than standard bicycles.

If your LECTRIC XP STEP-THRU 3.0 will not turn on, try the following solutions:

1. Charge the battery until the light on the charger turns from red to green. This may take up to 8 hours.

2. Insert the key in the battery and turn counterclockwise to the ON position, so the key is parallel with the frame. Then press and hold the power button to turn ON.

3. Follow the cable coming from the display down to the quick plug. You may need to unravel some of the plastic wrapping to access it. With a quick pull (do not twist), unplug the quick plug, inspect both sides of the plug, and reconnect by lining up the arrows on both ends. After checking the quick plug, press and hold the power button on the display control pad to turn on.

If the pedal assist or throttle on your LECTRIC XP STEP-THRU 3.0 do not work, try these steps:

1. Check that the PAS level is set between 1-5.

2. To test if PAS is working, do not operate the throttle.

3. To test if the throttle is working, do not pedal.

4. Check all quick plugs to ensure they are securely connected.

If you experience issues with the charging indicator lights, follow these troubleshooting steps:

If charging indicator lights do not illuminate:

1. Check that the cord is connected to the charger.

2. Check power availability at the main plug location.

3. If the battery does not charge, unplug and do not attempt to repair the cord or charger.

If the charging indicator light is always red:

• The battery pack may be defective.

Regular maintenance will keep your LECTRIC XP STEP-THRU 3.0 safe and fun to ride.

100 Mile Tune-Up:

After 100 miles or 5 full battery charge cycles, have the following services performed at a bicycle shop:

• Brake cables may need to be adjusted and tensioned properly.

• Shifting cables will stretch during the wear-in period. The derailleur may need to be adjusted.

• All hardware should be adjusted to the specified Tightening Torque.

Monthly (or about every 250-500 miles):

• Inflate tires to pressure within the recommended range printed on tire sidewalls.

• Lubricate chain.

• Check that all hardware is tightened to the torque specifications.

• Check your brake pads for signs of wear. Replace if necessary.

• Check your bicycle’s shifting performance. Adjust the derailleur if necessary.

• Clean the bicycle with low residue cleaner and dry completely. Lubricate after cleaning where necessary.

• Check spoke tension and adjust if necessary.

Quarterly (or about every 750-1500 miles):

• Check all items on the monthly service list above.

• Check tire tread for excessive wear. Replace if necessary.

• Check that electrical connectors and cable housings are secured away from moving parts and are free from damage. Replace if necessary.

Cleaning:

Do not submerge your eBike or its components in water, or use a pressure washer to clean. Clean your eBike carefully with a soft, damp cloth (using only mild soap and water). Rinse with water. The electrical components on your eBike are IP65 rated.