KYOCERA LAYLO M1400 (01) PDF MANUAL

1. Hold the phone face down.

2. Find the notch on the bottom of the phone. It is a rectangle. Using your thumbnail, pry the cover up from the bottom to remove.

3. Place the battery in the battery casing with the metal contacts facing down. The metal contacts of the battery must touch the metal contacts of the battery casing.

4. Replace the battery cover by sliding the notches into the openings on the top of the battery casing.

5. Snap the cover into place.

1. Connect the AC adapter to the microUSB jack on the side of the phone.

2. Plug the adapter into a wall outlet.

The battery icon in the upper-right corner of the screen tells you whether the phone is:

• Charging (the icon is animated)
• Partially charged
• Fully charged

You must have at least a partial charge in the battery to make or receive calls. You can safely recharge the battery at any time, even if it has a partial charge.

Note: Before removing the battery, make sure the phone is powered off.

• Do not disassemble or open the battery.
• Do not crush, bend, deform, puncture, or shred the battery.
• Do not attempt to insert foreign objects into the battery.
• Do not immerse the battery or expose it to water or other liquids. Even if a battery appears to dry out and operate normally, internal parts can slowly corrode and pose a safety hazard.
• Always keep the battery between 15 °C and 25 °C (59 °F and 77 °F). Do not expose the battery to extremes of temperature (heat or cold), fire, or other hazards such as a cooking surface, iron, or radiator.
• Never use any damaged battery.
• Only use the battery for its intended phone.
• Only use the battery with a qualified charger. Use of an unqualified battery charger may present a risk of fire, explosion, leakage, or other hazard. If you are unsure about whether a charger is qualified, contact customer support.
• Do not short-circuit the battery or allow metallic conductive objects such as keys, coins, or jewelry to contact the battery’s terminals.
• Replace the battery only with another qualified battery. Use of an unqualified battery may present a risk of fire, explosion, leakage, or other hazard.
• Promptly dispose of used batteries in accordance with local regulations and recycle if possible. Do not dispose as household waste.
• Supervise all battery usage by children.
• Avoid dropping the phone or battery. If the phone or battery is dropped, especially on a hard surface, an internal short-circuit can occur and pose a safety hazard. If you suspect battery damage, take it to a service center for inspection.
• Improper battery use may result in a fire, explosion, or other hazard.

• Playing games or using the Web.
• Taking pictures with the flash on.
• Keeping backlighting on.
• Operating when far away from a base station or cell site.
• Using data cables or accessories.
• Operating when no service is available, or service is available intermittently.
• High earpiece and ringer volume settings.
• Repeating sound, vibration, or lighted alerts.

If the screen seems frozen and the keypad does not respond to keypresses, reset the phone by completing the following steps:

1. Remove the battery cover.

2. Remove and replace the battery.

The phone’s keypad with the slide open includes:

1. Earpiece speaker.

2. Home screen.

3. Left softkey: Selects items that appear on the lower left of the display. At the home screen, you can select Menu.

4. Navigation key: Scrolls through lists and text entry fields and accesses the following shortcuts from the home screen:

• Scroll left to launch Browser.
• Scroll right to go to Tools & Games > Voice Memo.
• Scroll up to create a custom menu shortcut.
• Scroll down to go to Recent Calls > All.

5. Speakerphone key: Activates the speakerphone and answers calls.

6. Send key: Starts or answers a call. Press once to display the recent calls list or twice to redial the last number dialed. Press and hold to activate voice commands.

7. Keypad: For entering numbers, letters, or symbols.

8. * Shift key: Changes the text mode in text entry.

9. Right softkey: Selects items that appear on the lower right of the display. At the home screen, you can select Contacts.

10. OK key: Selects a menu item or option. At the home screen, you go to the main menu when you press the OK key.

11. Back key: Erases characters in text entry and returns you to the previous screen when navigating through menus.

12. End key: Turns the phone on and off, ends a call or browser session, and returns you to the home screen.

13. # Space key: Enters a space during text entry. Press and hold to activate or deactivate Vibrate Only.

14. 0 Next key: Cycles through word choices during text entry.

The back of the phone with the slide closed includes:

1. Camera lens.

2. Jack for AC adapter (included) and microUSB cable (sold separately).

3. Jack for a hands-free headset (sold separately).

4. Volume key: Raises or lowers ringer volume.

5. Camera key: Activates camera mode. Press and hold the Camera key to activate camera mode.

The following icons may appear on your phone’s screen:

From the home screen, press the OK key or select Menu to access the main menu. The menu options include:

• To turn your phone on, press the End key and wait until the phone display lights up.
• To turn your phone off, press and hold the End key until the phone plays a short musical sound and turns off.

1. Enter a phone number.

2. Press the Send key.

1. From View All, highlight a contact.

2. Press the Send key.

1. Press the Send key to open your call history.

2. Highlight a phone number or contact and press the Send key.

To redial the last number called, received or missed, press the Send key twice.

When a call comes in, the phone rings, vibrates, or lights up. The phone number of the caller also appears if it is not restricted. If the number is stored in your contacts list, the contact’s name appears. There are several ways you can answer a phone call:

Answer Using Earpiece

Press the Send key.

Answer Using Speakerphone

Press the Speakerphone key.

Answer Using Slide

You can set the phone to answer immediately when you open the slide. This feature does not apply to incoming data calls.

Press the End key.

1. Press and hold the Send key.

2. Follow the prompts.

Press the Volume key up or down to adjust the earpiece volume during a call.

• To turn on the speakerphone, press the Speakerphone key. The speakerphone icon appears on the home screen when the speakerphone is on.
• To turn off the speakerphone, press the Speakerphone key again.

Note: If you press the Speakerphone key during an incoming call, you will answer the call.

• To silence the phone without answering the call, press the Back key or press the Volume key up or down.
• To silence the phone and answer the call, press the Back key or press the Volume key up or down and then press the Send key.

Speed dialing allows you to assign a one- or two-digit shortcut to a contact. Before you can use speed dialing you must save a phone number as a contact and assign a speed dial location to it.

To call a contact that has a speed dial location:

1. Enter the one- or two-digit speed dial location.

2. Press the Send key.

You can call an emergency code even if your phone is locked or your account is restricted. When you call, your phone enters emergency mode. This enables the emergency service exclusive access to your phone to call you back, if necessary. To make or receive regular calls after dialing the code, you must exit this mode.

To dial an emergency code:

1. Enter the 3-digit emergency code.

2. Press the Send key.

When you have completed the emergency call:

1. Select Exit.

2. Select Exit again to confirm your choice.

From the text entry field, select Options > Numbers Only to enter a number when you press a key once.

The icon indicates you are in Numbers Only input mode. Press and hold the * Shift key to switch input modes.

From the text entry field, select Options > Normal Alpha to enter letters. You can enter text in the following ways:

• To enter a letter, press a key once for the first letter, twice of the second letter, and so on. If your phone is set to Spanish, accented letters are available. Wait for the cursor to move right and enter the next character. Press the # Space to enter a space.
• To change case mode for a single letter, press that key until you see the letter case you want. To change the case mode, press the * Shift key.
• To enter a number, press and hold a number key until the number appears on the screen.

The ABC icon indicates you are in Normal Alpha input mode. Press and hold the * Shift key to switch input modes.

From the text entry field, select Options > Rapid Entry to check words you are trying to spell against a dictionary of common words. You can enter text in the following ways:

• To enter words, press a key once. For example, to enter the word “Wyoming” press the 9 > 9 > 6 keys. If the word doesn’t match what you want, press 0 Next key to look at other word matches. When you see the word you want, scroll right.
• To change case mode, press the * Shift key.
• To enter a number, press and hold a number key until the number appears on the screen.

The icon indicates you are in Rapid Entry input mode. Press and hold the * Shift input key to switch input modes.

While entering text in Normal Alpha mode, you can enter symbols by pressing the 1 key until you see the symbol you want. Using this method, you have access to the following symbols:

@ ?! -, & : ‘ ]

To access the full set of symbols:

1. From the text entry field, select Options > Add Symbols.

2. Scroll up or down to view the list of symbols.

3. Press the number key corresponding to the symbols to enter it.

Select Browser to launch the browser. An alert appears notifying of airtime fees, if you have enabled web alerts. Select OK to continue.

If this is the first time you have connected to the Internet, a message informs you that security is not yet enabled for your browser. Select Yes to enable security.

A browser home page with a list of bookmarks and some browser menu options appear when you are connected to the Web. The lock icon appears in a secure session. You can do the following:

• To choose a site, scroll to the link and press the OK key.
• An underline and an arrow indicate that there is more text. Scroll down to view the rest of the text.
• Press the Back key to return to the previous screen.
• Press the End key to exit.
• Select Options to access more browser features.

1. Surf to the Web page you want to bookmark and select Options > Add to Bookmarks.

2. Edit the bookmark’s details, if needed.

3. Select Options > Save to save the bookmark.

To access your saved bookmarks, select Options > Bookmarks from any web page.

Select Contacts from the main menu to access the following functions:

1. From View All, enter the first letter of your desired contact and scroll to highlight it.

2. Do one of the following:

• Press the Send key to call the contact.
• Press the OK key to view the contact’s details.
• Select New to create a new contact.
• Select Options to access more functions.

1. From View All, select a contact.

2. At the contact details screen, select a number, address or note.

3. Select the detail you want to view. For example, to view a phone number, select View Number.

With Frequent List enabled, you can view 15 of your most frequently called contacts.

With Fast Find enabled, you can press one or two keys to view closer matches in your contacts list.

1. From the home screen, enter a phone number to save (include the area code).

2. Select Save > Save New Contact.

3. Enter a name for the contact.

4. Enter additional phone numbers, email addresses, and other contact details. (Scroll up or down to move through the contact fields.)

5. When done, select Save.

1. From Add New, enter a name for the contact. Scroll down to the next field when done.

2. Enter a primary number for the contact.

3. Enter additional phone numbers, email addresses, and other contact details. (Scroll up or down to move through the contact fields.)

4. When done, select Save.

When saving the phone number of an automated service, you may include a pause for dialing an extension.

1. From the home screen, enter a phone number.

2. Select Options and a type of pause:

• Time Pause: Causes the phone to stop dialing for two seconds.
• Hard Pause: Causes the phone to wait until you select Release while making the call.

3. Enter the remaining numbers and select Save > Save New Contact.

4. Complete the contact information and select Save.

1. From View All, select a contact.

2. At the contact details screen, select a number.

3. Select Call.

1. From View All, select a contact.

2. At the contact details screen, select a number or email address.

3. Select Send Text Msg.

4. Complete your text message and select Send.

1. From View All, select a contact.

2. At the contact details screen, select a number or email address.

3. Select Send Pic Msg.

4. Complete your multimedia message and select Send.

1. From View All, select a contact.

2. At the contact details screen, select the contact name.

3. Select Send as vCard > Via MMS Msg (to attach to a multimedia message), Via Bluetooth (to send to a Bluetooth-enabled device), or To Printer (to print on a Bluetooth-enabled device).

4. Complete the appropriate task to send the contact information.

Note: If your phone has no Bluetooth feature, you may send the contact information with a message only.

1. From View All, select a contact.

2. At the contact details screen, select Edit.

3. Enter additional phone numbers, email addresses, and other contact details. (Scroll up or down to move through the contact fields.)

4. When done, select Save.

1. From View All, select a contact.

2. At the contact details screen, select Edit.

3. Press down twice to scroll to the number type dropdown and press the OK key.

4. Select a number type. The appropriate icon appears next to the number in your contacts list.

5. Select Save.

1. From View All, select a contact.

2. At the contact details screen, select the contact name.

3. Select Ringer > Assign Ringer and a ringer from the list. (Scroll to play the ringers.)

1. From View All, select a contact.

2. At the contact details screen, select the contact name.

3. Select Msg Tone > Assign Msg Tone and a ringer from the list. (Scroll to play the ringers.)

1. From View All, select a contact.

2. At the contact details screen, select the contact name.

3. Select Picture > Assign Picture to assign a picture.

Use Prepend to add a prefix, such as an area code, to a phone number:

1. From View All, select a contact.

2. At the contact details screen, select a number.

3. Select Prepend to enter the prefix at the beginning of the number.

4. Select Save.

1. From View All, select a contact.

2. At the contact details screen, select a number.

3. Select Add Speed Dial.

4. Select a location from the list to assign the speed dial number.

When a contact has more than one number, the first number becomes the primary number by default. To change the contact’s primary number:

1. From View All, select a contact.

2. At the contact details screen, select a number.

3. Select Primary Number > Yes.

1. From View All, select a contact.

2. At the contact details screen, select a number or email address.

3. Select Add To Group.

4. Select groups from the list provided. A checkmark appears next to each selection. You can also remove a checkmark.

5. When finished, select Done.

1. From View All, select a contact.

2. At the contact details screen, select a Web address.

3. Select Launch Web.

1. From View All, select a contact.

2. At the contact details screen, select a number, address or note.

3. Select your desired erase option and then select Yes. For example, to erase an email address, select Erase Address > Yes.

1. From View All, select a contact.

2. At the contact details screen, select the contact name.

3. Select Erase Contact > Yes to erase the entire contact.

From Erase Contacts, select Contacts Only > Yes > Yes to erase all your contacts.

Note: You cannot recover deleted information.

From Erase Contacts, select Erase All > Yes > Yes to erase all your contacts and groups.

Note: You cannot recover deleted information.

1. Select Groups to view your preloaded groups, followed by the custom groups you have created.

2. Highlight a group and do one of the following:

• Press the OK key to view the group details.
• Select New to create a new group.
• Select Options to access more functions.

1. From Groups, select New.

2. Enter a name for the group and select Next.

3. Select contacts from the list provided. A checkmark appears next to each selection. You can also remove checkmarks.

4. When finished, select Done.

1. From Groups, highlight a group.

2. Select Options > Send Text Msg.

3. Complete your text message and select Send.

1. From Groups list, highlight a group.

2. Select Options > Send Pic Msg.

3. Complete your multimedia message and select Send.

1. From Groups, highlight a group.

2. Select Options > Edit.

3. If you are modifying a group you created, select Next. Otherwise, go to the next step.

4. Select contacts from the list provided. A checkmark appears next to each contact in the group. Press the OK key to add or remove checkmarks.

5. When finished, select Done.

1. From Groups, select a group.

2. At the group details screen, scroll to the group name.

3. Select Options > Ringer > Assign Ringer and a ringer from the list. (Scroll to play the ringers.)

1. From Groups, select a group.

2. At the group details screen, scroll to the group name.

3. Select Options > Msg Tone > Assign Msg Tone and a ringer from the list. (Scroll to play the ringers.)

1. From Groups, select a group you have created.

2. At the group details screen, scroll to the group name.

3. Select Options > Picture > Assign Picture to assign a picture.

1. At the Groups list, highlight a group.

2. Select Options > Send > Via Bluetooth.

3. Complete the appropriate task to send the group information.

You can create a group specifically for messaging, based on a contact group.

1. From Groups, highlight a group.

2. Select Options > Create Msg Group.

3. Modify the name for the group and select Next.

4. Select contacts from the list provided. A checkmark appears next to each contact in the group. Press the OK key to add or remove checkmarks.

5. When finished, select Done.

1. From Groups, highlight a group.

2. Select Options > Erase > Yes.

1. From Speed Dial List, highlight an unassigned number (marked as empty).

2. Select Assign.

3. At the contacts list, select a contact.

4. At the contact details screen, select a phone number.

1. From Speed Dial List, highlight an assigned number.

2. Select Erase > Yes.

Your phone creates a voice dial tag for each contact that has a name field which is not blank or a name that is more than five syllables. You can enable or disable the voice dial tags associated with your contacts.

1. From Voice Dial List, press the OK key to add or remove checkmarks. A checkmark appears next to each enabled voice dial. (Scroll through the list to play the voice dial tags.)

2. When done, select Save.

Select Contacts Count to check how many contacts you have stored.

Here are some tips for using your phone’s camera:

• You cannot activate the camera while on an active call or while browsing files in the media gallery.
• Once the camera is active, the home screen acts as the viewfinder.
• If you get a “Low memory” error, check your resolution and quality compression settings.
• If there is no activity within 45 seconds after you turn your camera on, the camera times out and returns to the previous launch point.
• Menu settings and options can only be accessed when the camera is active.
• Numbers in the top right corner indicate the number of snapshots remaining before the phone runs out of memory.

1. To activate the camera, press and hold the Camera key. You can also select Camera from the main menu.

2. Focus on the image using the phone’s display as a viewfinder.

3. To take a picture, press the OK key. The picture is saved to Camera Pictures.

4. Select Send > Via EMS Msg (to attach to an enhanced message), Via MMS Msg (to attach to a multimedia message), Via Bluetooth (to send to a Bluetooth-enabled device), or To Printer (to print on a Bluetooth-enabled device).

Select Erase to delete the picture from your phone.

5. Press the End key to exit camera mode.

From camera mode, select Options > Settings > Resolution and a size for your pictures.

Numbers in the bottom left corner indicate the current resolution setting.

From camera mode, select Options > Settings > Self Timer and a time.

The icon indicates the timer is activated. When you take a picture, a beep plays three seconds from the time the shutter snaps the picture.

From camera mode, select Options > Settings > Date/Time > On to place a date/time stamp on each picture taken.

The icon indicates when the date/time stamp is on.

From camera mode, select Options > Settings > Multishot > On to take multiple pictures.

The icon indicates multishot mode is enabled. When you take a picture, press and hold the OK key to take multiple pictures. A single tone plays for each picture taken.

Your camera is set to a lower resolution during multishot mode. The resolution setting returns to the previous setting when you are done.

1. From camera mode, select Options > Settings > Shutter Sound.

2. Select a sound to play when the shutter takes a picture.

1. From camera mode, select Options > Settings > White Balance.

2. Scroll left or right to select the white balance setting. Look at the home screen to see how each setting looks.

1. From camera mode, select Options > Settings > Color Tone.

2. Scroll left or right to select a color tone. Look at the viewfinder to see how each setting looks.

From camera mode, select Options > Settings > Picture Quality and a quality level for your picture.

When you select a higher quality level, the size of the file is bigger.

1. From camera mode, select Options > Brightness.

2. Scroll left or right to change the brightness level. Press the OK key to set the brightness.

From camera mode, select Options > Camera Pictures to see all of the pictures you have taken. These are located in Camera Pictures.

1. From camera mode, select Options > Frames.

2. Scroll left or right to view the frames available.

3. Select OK to choose a frame.

4. Take a picture with the frame. The frame is part of the image and can not be removed.

Select Recent Calls from the main menu to access the following functions:

1. From All, highlight a number.

2. Press the Send key to call the number or select Options to access more features.

This list contains all calls made and received.

1. From Incoming, highlight a number.

2. Press the Send key to call the number or select Options to access more features.

This list contains all calls received.

1. From Outgoing, highlight a number.

2. Press the Send key to call the number or select Options to access more features.

This list contains all calls you have made.

1. From Missed, highlight a number.

2. Press the Send key to call the number or select Options to access more features.

This list contains all calls you received, but did not answer.

When you have missed a call, “Missed Call” appears on your screen. You can do one of the following:

• To clear the screen, select OK.
• To view the call details, select Calls and press the OK key.
• To return the call, select Calls and press the Send key.

1. At a call list, highlight a number.

2. Select Options > Save.

3. Select Save New Contact to create a new contact or Add to Existing to add a number to an existing contact.

1. At a call list, highlight a contact.

2. Select Options > View to see the contact details screen.

1. At a call list, highlight a contact.

2. Select Options > Send Text Msg.

3. Complete your text message and select Send.

1. At a call list, highlight a contact.

2. Select Options > Send Pic Msg.

3. Complete your multimedia message and select Send.

1. At a call list, highlight a contact.

2. Select Options > Erase Record > Yes.

From Erase Call List, select a call list to erase records from. For example to erase all records from the incoming call list, select Incoming > Yes.

From Erase Call List, select All > Yes to erase all records from all call lists.

Select Life Timer to view the number of calls and the total call time. Select Done when finished.

This timer tracks all calls made and received for life of the phone and cannot be reset.

Select Recent Calls to view the number of calls and the total call time. Select Done when finished.

This timer tracks all calls made and received since you last reset the timer. To reset this timer to zero, select Reset > Yes.

Select Home Calls to view the number of calls and the total call time. Select Done when finished.

This timer tracks all calls made and received in your home network since you last reset the timer. To reset this timer to zero, select Reset > Yes.

Select Roam Calls to view the number of calls and the total call time. Select Done when finished.

This timer tracks all roaming calls made and received since you last reset the timer. To reset this timer to zero, select Reset > Yes.

Select Incoming Calls to view the number of calls and the total call time. Select Done when finished.

This timer tracks all calls received since you last reset the timer. To reset this timer to zero, select Reset > Yes.

Select Outgoing Calls to view the number of calls and the total call time. Select Done when finished.

This timer tracks all calls made since you last reset the timer. To reset this timer to zero, select Reset > Yes.

Select Kilobyte Counter to view the amount of kilobytes sent during data calls. Select Done when finished.

This timer tracks kilobytes sent during data calls made, data calls received, and for the life of the phone. To reset the data counter to zero, select Options > Reset > Yes.

Select Messaging from the main menu to access the following functions:

You can only send text messages to phone numbers capable of receiving them or to email addresses if supported.

1. From New Text Msg, enter a recipient’s phone number or email address. (Select Options to access contacts, groups or recently used addresses. Scroll down to move to the next field when done.)

You can message up to ten recipients at once. Use comma or spaces to separate addresses.

2. Enter the message. (Select Options to access more features.)

3. When done, select Send.

You can only send multimedia messages to phone numbers capable of receiving them or to email addresses. If the character and file size limit for a single multimedia message is exceeded, the message must be edited to meet the size limitation.

1. From New Pic Msg, enter a recipient’s phone number or email address. (Select Options to access contacts, groups or recently used addresses. Scroll down to move to the next field when done.)

You can message up to ten recipients at once. Use comma or spaces to separate addresses.

2. Repeat the first step for CC and BCC, if needed.

3. Enter a subject.

4. Enter a message.

5. Attach an image file. (Select Options to access more features.)

6. Attach a sound file. (Select Options to access more features.)

7. When done, select Send.

If you receive a call while creating a message a notification appears. Do one of the following:

• Select Ignore to ignore the call and return to the message screen.
• Press the Send key to answer the call and your phone automatically saves the message to Drafts.

1. At the compose message screen, select Options > Contacts when entering a phone number or email address.

2. Select a contact from the contacts list.

3. Select a number or address.

4. Complete your message.

1. At the compose message screen, select Options > Recent List when entering a phone number or email address.

2. Select a number or address.

3. Complete your message.

1. At the compose message screen, select Options > Recent Calls when entering a phone number or email address.

2. Select a number.

3. Complete your message.

1. At the compose message screen, select Options > Message Groups when entering a phone number or email address.

2. Select a group.

3. Complete your message.

1. At the compose message screen, select Options > Save Address when entering a phone number or email address.

2. Select a number or address.

3. Select Options > Save New Contact (to create a new contact) or Options > Add to Contact (to add the number or address to an existing contact).

1. At the compose message screen, select Options > Add Address when entering the text to add more recipients.

2. Enter a number or address to add.

3. Complete your message.

1. At the compose message screen, select Options > Online Album when entering a phone number or email address to upload the message to your online photo album.

2. Complete your message.

At the compose message screen, select Options > Save Message when entering the text. Your phone saves the message to Drafts for you to complete at a later time.

• From Drafts, highlight your desired message.
• Select Edit or Options > Edit.
• Complete your message.

1. At the compose message screen, select Options > Insert QuickText when entering the text.

2. Select a preset text entry.

3. Complete your message.

1. At the compose message screen, select Options > Save as QuickText when entering the text to use it later as preset text.

2. Complete your message.

When viewing a received message, select Options > Save as QuickText to use it later as preset text.

1. At the compose message screen, select Options > Insert Note when entering the text.

2. Select a memo.

3. Complete your message.

1. At the compose message screen, select Options > Insert Picture when entering the text.

2. Select a file.

3. Complete your message.

1. At the compose message screen, select Options > Insert Sound when entering the text.

2. Select a file.

3. Complete your message.

1. At the compose message screen, select Options > Insert Contacts when entering the text.

2. Select a contact from your contacts list.

3. Complete your message.

Use slides in a multimedia message to send multiple files of the same type, such as pictures or voice memos. A multimedia message may have up to ten slides.

1. At the compose message screen, select Options > Add New Slide when entering the text.

2. Select a slide and add more files or text if needed.

To navigate through the slides, select Options > Next Slide or Previous Slide.

To erase the current slide, select Options > Erase Slide.

3. Complete your message.

You can only attach a limited number of files.

1. At the compose message screen, select Options > Media Gallery when adding a media file.

2. Select a file to add to your message.

To remove a media file, select the applicable option. For example, to remove a sound, select Options > Remove Sound.

3. Complete your message.

1. At the compose message screen, select Options > Take a Picture when adding an image.

2. Take a picture.

3. Select it to add to your message.

4. Complete your message.

1. At the compose message screen, select Options > Record Sound when adding a sound.

2. Record a sound.

3. Select it to add to your message.

4. Complete your message.

1. At the compose message screen, select Options > Preview Message when entering the message or media file.

2. Do one of the following:

• If the message has more than one slide, select Next to view the next slide.
• If the message has only one slide, select Send to send message.
• Select Options to access more features.

1. When entering a message, select Options > Msg Settings > Msg Receipt > Request to request a message delivery notice.

2. Complete your message.

1. When entering a message, select Options > Msg Settings > Set Priority to set the priority level.

2. Complete your message.

1. When entering the message, select Options > Msg Settings > Callback Number.

2. Enter your callback number and select OK.

3. Complete your message.

1. When entering a message, select Options > Msg Settings > Send Later.

2. Select Immediate or Set Time to set a specific time to send the message.

3. Press the OK key to change the time.

• Scroll left or right to move between the hour, minute, and AM/PM.
• Scroll up or down to change the hour, minute, and AM/PM.

4. Select Next.

5. Press the OK key to change the date.

• Scroll left or right to move between the month, day, and year.
• Scroll up or down to change the month, day, and year.

6. Select Done.

7. Complete your message. Your phone will save the message and send it later.

1. When entering a message, select Options > Msg Settings > Validity Period.

2. Select Set Time to set how long to keep your message valid before removing it from the phone if not sent.

3. Press the OK key to change the time.

• Scroll left or right to move between the hour, minute, and AM/PM.
• Scroll up or down to change the hour, minute, and AM/PM.

4. Select Next.

5. Press the OK key to change the date.

• Scroll left or right to move between the month, day, and year.
• Scroll up or down to change the month, day, and year.

6. Select Done.

7. Complete your message.

1. When entering the message, select Options > Msg Settings > CC & BCC to enable or disable the CC and BCC address fields.

2. Complete your message.

When receiving a message, your phone displays a notification and the message icon appears at the top of your screen. The message icon flashes with an urgent message alert if the message is urgent.

1. When a message notification appears, select Inbox (to view the message) or Ignore (to clear the notification).

An icon appears at the top of your screen when you have an unread message.

2. From Inbox, highlight a message and select View > Reply (to compose your message) or Options (to access more features).

3. Complete your message and select Send.

When receiving a message in auto retrieve mode, your phone automatically downloads it with a notification.

1. At a message notification, select View (to view the message) or Later (to check it later).

2. After viewing the message, select Reply or Options > Reply if the message has more than one slide.

Select Options to access more features.

3. Complete your message and select Send.

When receiving a message in prompt mode, your phone displays a notification showing a new message is available for download.

1. At the download notification, select Yes (to download the message) or Options (to retrieve it later or erase it without downloading).

2. At the message notification, select View (to view the message) or Later (to check it later).

3. Select Reply or Options > Reply if the message has more than one slide.

Select Options to access more features.

4. Complete your message and select Send.

Select Options to access more features.

1. When viewing a received message, select Options > Forward.

2. Enter a number or address.

3. Complete your message and select Send.

1. When viewing a received message, select Options > Reply All to send your reply to all the message recipients.

2. Complete the message and select Send.

1. When viewing a received message, select Options > Reply with Copy.

The original message appears in your reply message.

2. Complete your message and select Send.

When viewing a received message, select Options > Call to call the sender.

When viewing a received message, select Options > Save Message to save it to Saved Msgs.

When viewing a received message, select Options > Recipients to check all recipients of the message.

When viewing a received message, select Options > Sender to view an existing contact, add to an existing contact, or create a new contact depending on the sender.

When viewing a received message, select Options > Lock Msg to protect it from accidental deletion. To unlock the message, select Options > Unlock Msg.

1. From Inbox, select Options > Sort.

2. Select a sort option.

When viewing a received message, select Options > Launch Browser to go to a web address included in the message.

When viewing a received message with files attached, select Options > Play (to play an attached file), Stop (to stop playing), or Mute (to turn off the sound).

When viewing a received message with files attached, select the applicable save option to save the attached files, including graphics, sounds, contacts (vCard), or events (vCal). For example, to save a contact, select Options > Save Contact.

When viewing a received message containing multiple slides, use the following options to navigate through the slides.

• Next to view the next slide.
• Options > Replay to restart the message from the beginning slide.
• Options > Pause to pause at the current slide.
• Options > Resume to resume playing the slides.
• Options > Done to exit the message.

When viewing a received message, select Options > Message Info to view the message priority, sent time, size, etc.

When viewing a received message, select Options > Replay to restart the message (including a slide or sound if contained) from the beginning.

Before your phone can receive voicemail messages, you need to set up a password and record a personal greeting with your service provider.

When you have set up your voicemail, all unanswered calls to your phone are automatically transferred to voicemail, even if your phone is in use or turned off.

1. Press and hold the 1 key.

2. Follow the system prompts to create a password and record a greeting.

When you receive a voicemail message, a notification with a voicemail message icon appears at the top of your screen.

• At the voicemail notification, select Call to call your voicemail number and follow the system prompts to retrieve the message. Select Ignore to clear the notification without checking messages. The notification icon remains on top of the screen until you listen to the message.
• When only the voicemail message icon appears on top of the screen, select Voicemail and follow the system prompts to retrieve the message.

Use the following symbols to check the Sent folder for the status of messages successfully sent.

Use the following symbols to check your Outbox for the status of messages sent but still in process.

You may not be able to send or receive messages if your phone’s memory is nearly full, or if digital service is not available at the time. To free up memory, erase old messages.

If you go over the character limit for a single message, the phone may automatically append an empty segment to your message to make space.

When you start a message, the maximum character limit appears once you are in the message entry field. This number counts down as you enter characters, until it reaches 0.

If you continue to enter text after this counter reaches 0, a message segment may be appended. When you reach the message size limit, you are prompted to edit the message or alerted that the message is being appended.

1. From Browser Alerts, select an alert.

2. Select Connect to launch the browser.

1. From Alerts, select Msg Alert.

2. Select an alert for messages.

If you select an & Remind alert, the phone notifies you once when receiving a new message and notifies you again every five minutes. To stop a reminder alert, select Ignore.

1. From Alerts, select Page Alert.

2. Select an alert for pages.

If you select an & Remind alert, the phone notifies you once when receiving a new message and notifies you again every five minutes. To stop a reminder alert, select Ignore.

1. From Alerts, select Voicemail Alert.

2. Select an alert for voicemails.

If you select an & Remind alert, the phone notifies you once when receiving a new message and notifies you again every five minutes. To stop a reminder alert, select Ignore.

From Msg List View, select one of the following to set your message list display:

• Sender & Preview: Displays the sender and first part of messages.
• Sender & Date-Time: Displays the sender and sent time of messages.

You can create a signature to appear at the end of all outgoing messages.

1. From Signature, enter your signature.

2. Select OK to save the signature.

Note: The signature counts towards the character limit of your message.

Your phone comes with preset messages, such as “Please call me,” which you can insert into the body of a text message. You can edit or create up to 40 preset messages.

1. From QuickText, do one of the following:

• Scroll to a preset message and select Edit.
• Select New Msg to create a new preset message.

2. Enter or edit the text.

3. Select Save.

From Auto Retrieve, select one of the following:

• Disabled: Turns off auto retrieve and prompts you before downloading any multimedia messages.
• Enabled: Turns on auto retrieve to automatically download multimedia messages.

From CC and BCC, select Disabled (to hide the CC and BCC fields) or Enabled (to show them).

1. From Callback Number, enter a new number to change your default callback number.

2. Select OK to save the number.

From Save to Sent, select Enabled to automatically save outgoing messages to the Sent Msgs folder.

Use Auto-Erase to set your phone to erase messages automatically when it needs memory for incoming messages.

From Auto-Erase, select one of the following:

• Disabled: Erases no messages.
• Inbox Msgs: Erases old messages in Inbox when memory is needed.
• Sent Msgs: Erases old messages in Sent Msgs when memory is needed.
• Both: Erases old messages in both Inbox and Sent Msgs when memory is needed.

You can change the default text entry mode when creating a text message. This setting applies only to the Message field, not the Send To field.

From Default Text, select Normal Alpha (to enter text letter by letter) or Rapid Mode (to enter text with word recognition).

From Text Msg Receipt, select Request to request a notification when a recipient has received your text message.

From Pic Msg Receipt, select Request to request a notification when a recipient has received your multimedia message.

1. From Voicemail Number, select Edit.

2. Enter your voicemail number.

3. Select Save.

From Erase Recent List, select Yes to clear the list of recipients you have recently sent messages to.

1. From Message Groups, view your preloaded groups, followed by the custom groups you have created.

2. Highlight a group and do one of the following:

• Press the OK key to view the groups details.
• Select New to create a new group.
• Select Options to access more functions.

1. From Message Groups, select New.

2. Enter a name for the group and select Next.

3. Select contacts from the list provided. A check mark appears next to each selection. You can also remove checkmarks.

4. When finished, select Done.

1. From Message Groups, highlight a group.

2. Select Options > Send Text Msg.

3. Complete your text message and select Send.

1. From Message Groups, highlight a group.

2. Select Options > Send Pic Msg.

3. Complete your multimedia message and select Send.

1. From Message Groups, highlight a group.

2. Select Options > Edit.

3. If you are modifying a group you created, select Next. Otherwise, go to the next step.

4. Select contacts from the list provided. A checkmark appears next to each contact in the group. Press the OK key to add or remove checkmarks.

5. When finished, select Done.

1. From Message Groups, select a group.

2. At the groups details screen, scroll to the group name.

3. Select Options > Msg Tone > Assign Msg Tone and a ringer from the list. Scroll to play the ringers.

1. From Message Groups, highlight a group.

2. Select Options > Send > Via Bluetooth.

3. Complete the appropriate task to send the contact information.

1. From Message Groups, highlight a group.

2. Select Options > Erase > Yes.

When viewing a received message, select Options > Erase > Yes.

Note: You can erase a scheduled message, but cannot cancel its delivery.

From Erase Msgs, select a folder to erase messages from. For example, to erase received messages, select Inbox > Yes.

Note: You cannot recover deleted information.

From Erase Msgs, select All > Yes to erase all messages from all folders, except for voicemail messages.

Note: You cannot recover deleted information.

From Message Count screen, check how many messages you have stored.

Select Settings from the main menu to access the following functions:

Before you can connect your phone with a Bluetooth device, you need to enable the Bluetooth feature on your phone.

From Settings, select On/Off > On.

To enable your phone to communicate with a Bluetooth device, you need to “pair” the device with your phone.

1. Prepare the Bluetooth device (accessory) for pairing as described in the device’s user guide.

2. From My Devices, select Find New. Your phone then searches and detects any available Bluetooth devices in the vicinity.

3. At the device list, highlight a device and select Add.

Accept the pairing if prompted.

4. If necessary, enter the password provided with the Bluetooth device and select OK.

With the password accepted, the device appears in your device list.

Before you can use Bluetooth, you must get your phone ready to communicate with a device. This is called “connecting.”

To connect your phone to a Bluetooth device, from My Devices, highlight a device and select Connect.

A notification appears confirming the connection. You can now use the device with your phone.

From My Devices, highlight a connected device and select Disconnect.

1. From My Devices, highlight a device.

2. Select Options > Rename.

3. Enter a new name and select Save.

1. From My Devices, highlight a device.

2. Select Options > Delete > Yes.

A Bluetooth device paired with your phone may have more than one service profile (such as Headset, Handsfree, and so on). Do the following to check the services available:

1. From My Devices, highlight a device.

2. Select Options > Services.

3. At the service list, highlight a profile and select Connect to change the active profile.

You can change the name presented for other Bluetooth devices’ search of your phone.

From My Name, enter a new name and select Save.

By default your phone is always visible, if set to visible mode. You can limit the time your phone is visible to other Bluetooth devices.

From Visible Duration, select an option to set the phone visible for your selected time before becoming invisible.

Select Services to view a list of the Bluetooth service profiles your phone supports.

From OBEX Authentication, select Enabled.

With object exchange (OBEX) authentication enabled, you need a user name and password to transfer files via Bluetooth.

From Ringer Type, select a ringer. (Scroll down the list to play the ringers.)

From Roam Ringer, select Enabled to activate a specific ringer for roaming calls.

From Ringer Shuffle, select Enable to turn on the ringer shuffle.

1. From Ringer Shuffle, select Edit.

2. Select Add (to include the file in the shuffle) or Remove (to remove the file from the shuffle).

3. When finished, select Options > Done.

1. From Ringer Shuffle, select View. Only the files used in your shuffle appear.

2. Select Edit to modify the shuffle list or press the Back key to exit.

From Ringer Mode, select one of the following:

• Normal Sounds: Rings for the incoming call or alert (in effect, returning the phone to a non-silent mode).
• Vibrate Only: Vibrates for the duration of the incoming call or other alerts.
• Vibe Then Ring: Vibrates for the first ten seconds and then rings for the remainder of the incoming alert.
• Lights Only: Lights up for the duration of the incoming call or other alerts.

You can also press and hold the # Space key to toggle between Vibrate Only mode and Normal Sounds mode.

1. From Ringer Volume, scroll right or left to set the ringer volume.

2. Press the OK key to save.

1. From Spkrphone Volume, scroll right or left to set the speakerphone volume.

2. Press the OK key to save.

1. From Earpiece Volume, scroll right or left to set the earpiece volume.

2. Press the OK key to save.

1. From Key Volume, scroll right or left to set the keypad volume.

2. Press the OK key to save.

1. From Slide Sounds, select Slide Open or Slide Close.

2. Select a sound. (Scroll down the list to play the sounds.)

1. From Pwr On/Off Sound, select Power On Sound or Power Off Sound.

2. Select a sound to play your phone powers on or off. (Scroll down the list to play the sounds.)

From Key Sounds, select Tone, Click, or Off to set the sounds you hear when pressing the keypad.

From Key Length, select Normal or Long to set the length of the keypad tone.

You can select a wallpaper for your phone’s home screen.

1. From Set Wallpaper, select Camera Pictures, Saved Images, or Wallpapers.

To turn off wallpaper, select None.

2. Select a file. You may need to resize or crop the file.

3. Select Done.

From Wallpaper Shuffle, select Enable to turn on wallpaper shuffle.

1. From Wallpaper Shuffle, select Edit.

2. Select Add (to include a file in the shuffle) or Remove (to remove a file from the shuffle).

3. When finished, select Options > Done.

1. From Wallpaper Shuffle, select View. The files in your shuffle appear.

2. Select Edit to modify the shuffle list or press the Back key to exit.

1. From Wallpaper Shuffle, select Set Shuffle Time.

2. Select an interval time from the list. Your wallpaper changes to another file in the shuffle at the selected interval time.

Screensavers appear on the home screen, activated ten seconds after the last keypress. Incoming calls and alerts override the screensavers.

1. From Set Screensaver, select Camera Pictures, Saved Images, or Screensavers.

To turn off screensaver, select None.

2. Select a file. You may need to resize or crop the file.

3. Select Done.

From Themes, select a color theme for the display background.

From Main Menu View, select one of the following:

• Grid: Displays icons of each menu item, with its name at the top of the screen.
• List: Displays a list of all menu items.

The next time you view the Menu, your selected menu style appears.

The banner is the personal label for your phone, appearing on the home screen above the time and date.

1. From My Banner, select Edit.

2. Press the Back key to clear the current banner.

3. Enter your new text (up to 14 characters) or press the # Space key for a blank banner.

4. Select Save.

Use Backlighting to minimize the bright time and maximize the battery life.

From Backlighting, select one of the following:

• Always Dim: Forces the backlight to remain dim before turning off.
• 7 Seconds, 10 Seconds, 15 Seconds, or 30 Seconds: Turns backlighting on for the set time after your last keypress.
• Always Bright: Forces the backlight to remain bright before turning off.

1. From Brightness, scroll to change the brightness level.

2. Select Save.

From Language, select a language.

From Time/Date Format, select a time and date format.

In Airplane mode, you can set the time and date manually.

Note: You can only access Set Time/Date with Airplane Mode enabled.

1. From Set Time/Date, do the following to change the date:

• Scroll left or right to move between the month, day, and year fields.
• Scroll up or down to change the month, day, and year.

2. Press the OK key to save the date.

3. Do the following to change the time:

• Scroll left or right to move between the hour, minute, and AM/PM fields.
• Scroll up or down to change the hour, minute, and AM/PM.

4. Press the OK key to save the time.

5. Select Done.

While in an airplane, it is normally required that you turn off your mobile phone because it emits RF signals that interfere with air traffic control. In airplane mode, however, your phone does not emit RF signals. You cannot make or receive calls, send text messages, use the Browser or Bluetooth, but you can play games, use the Scheduler, set the clock, and make emergency calls to designated emergency numbers. Please check with uniformed personnel before operating your phone in Airplane mode.

From Airplane Mode, select Enabled > OK to activate airplane mode.

With airplane mode enabled, you can also set the time and date manually.

Use Auto Keyguard to automatically lock the keypad after 30 seconds of inactivity to prevent accidental key presses.

From Auto Keyguard, select Enabled or from the home screen, press and hold the Back key.

From the home screen, select Unlock and press the OK key to unlock the keypad.

Auto-hyphenation, when enabled, automatically inserts hyphens into your phone numbers to be consistent with the U.S. dialing plan (or the North American Numbering Plan).

From Auto-Hyphen, select Enabled to turn on auto-hyphenation.

The 1-Touch Dialing feature is the fastest way to call a speed dial location. To call a contact with speed dial, press and hold the speed dialing location.

If it is a two-digit location, press the first digit briefly, then press and hold the second digit.

From 1-Touch Dialing, select Enabled to turn on 1-touch dialing.

Use Answer Hold to place incoming calls on hold until you are ready to answer them.

Note: The Answer Hold feature will not work if the Open to Answer feature is enabled.

1. From Answer Hold, select Enabled.

2. If you have not recorded a hold message, you need to record one, such as “Please hold. I’ll answer in a minute.”

Record the message twice, as prompted.

3. Select Save or Options and one of the following:

• Play to replay your message.
• Re-Record to record your message again.
• Exit to exit.

The next time a call comes in, you can place it on hold.

You can place a call on hold with Answer Hold enabled.

1. From Answer Hold, select Re-Record Msg.

2. Record the message twice, as prompted.

3. Select Save to save the message or Options and one of the following:

• Play to replay your message.
• Re-Record to record your message again.
• Exit to exit.

1. From Fast Find, select Enabled to turn on fast find.

2. From the home screen, press the keys corresponding to the letters of the name you want to find. A matching contact or speed dial entry appears.

3. Scroll to your desired contact and press the Send key to call the number.

From Frequent List, select Enabled. With Frequent List enabled, the last 15 of your most frequently called contacts appear at the beginning of your contacts list. Scroll past the double line to view the entire contacts list.

From Minute Alert, select Enabled. Your phone alerts you with a short beep ten seconds before each minute passes during a call.

From Missed Call Alert, select an alert type for missed calls.

If you select an & Remind alert, the phone notifies you once when receiving a new message and notifies you again every five minutes. To stop a reminder alert, select Ignore.

From Open to Answer, select Enabled to answer calls by opening the phone.

From Close to End, select Enabled to end calls by closing the phone.

From Any Key Answer, select Enabled to answer calls when you press any key on the keypad.

You can modify the Navigation key and Left softkey settings to set up your desired shortcut.

1. From Customize Keys, select Up Nav Key, Left Nav Key, Right Nav Key, Down Nav Key, or Left Soft Key.

2. Select your desired menu option for the targeted key shortcut.

1. From the home screen, scroll up and hold.

2. Select Edit.

3. Select features from the list provided. A check mark appears next to each selection. You can also remove checkmarks.

4. Select Save after selecting all your options.

Your new selections appear the next time you select your custom menu.

From Automatic Add, select Enabled to automatically add a contact to your voice dial list when you create a new contact.

Use Expert Mode to speak a command after you hear a tone instead of following the initial voice prompts.

From Expert Mode, select one of the following:

• Normal: Sets the phone to default voice prompts.
• Expert: Sets the phone to sound tones instead of voice prompts.

You can set the phone to display up to three voice recognition contacts when calling or searching for a contact with voice commands.

From Display Results, select Single Best or Three Best.

You can set the number of digits used for a phone number in your voice dial list.

From Digit Lengths, select one of the following options:

• North American: Recognizes only 7, 10, and 1 + 10 digits in a phone number.
• Permit All: Allows 4-14 digits in a phone number.

You can set your phone to answer a call with your voice when using a hands-free accessory.

1. From Auto-Answer, select Disabled.

2. From Ringer Mode, select Normal Sounds.

3. From Headset Sounds, select Out of headset.

4. From Voice Answer, select With Accessory.

When you receive an incoming call, the phone prompts “Incoming call, answer?”. With the caller recognized as a contact entry in your phone, the phone prompts “Incoming call from (Name), answer?” Do one of the following:

• Say “Yes” or press any key except the End key to answer the call.
• Say “No” or press the End key to ignore the call.
• Remain silent. The voice alert repeats twice and the phone rings once before returning to the home screen.

If your phone has trouble recognizing your voice, you can train your phone to recognize your voice specifically for numbers.

1. From Voice Training, read the message and select OK > Train Numbers > OK.

2. Follow the prompts for each number until training is complete.

Note: You must read the numbers digit by digit for voice training to work.

With a headset attached to your phone, you can play the ringer through the headset or phone speaker.

From Headset Sounds, select Out of phone (ringing from the phone speaker) or Out of headset (ringing from the headset).

From Auto-Answer, select After 5 Seconds.

The phone automatically answers after five seconds with a headset attached.

From Com Port Speed, select a data rate at which your phone connects to a laptop or PC.

You can connect the phone to a teletype (TTY) device for the hearing impaired.

Note: Enable TTY only when using the phone with a TTY device.

1. Connect the TTY device to your phone.

2. From TTY Device, select OK to clear the notification.

3. Select one of the following:

• TTY Off: Disables TTY.
• TTY On: Enables TTY devices.
• TTY On + Talk: Enables TTY devices and voice carry over.
• TTY On + Hear: Enables TTY devices and hearing carry over.

Note: You can also enter ##889 with your keypad and select TTY to enable TTY.

With a T-coil hearing aid device connected, you can enable the hearing aid feature.

1. Connect the T-coil hearing aid device to your phone.

2. From T-coil Hearing Aid, select OK > Enabled.

From Privacy Alert, select Enabled to set your phone to alert you when enhanced digital CDMA privacy is lost or regained.

From Voice Privacy, select Enhanced to use enhanced digital CDMA privacy.

Use this setting if you want the phone to alert you when you roam outside of your home service area.

From Roam/Svc Alert, select one of the following:

• Disabled: Turns roaming service alert off.
• When no svc: Alerts you with three tones decreasing in pitch when service is lost and three tones increasing in pitch when service is acquired again.
• On roam change: Alerts you with two decreasing tones when roaming service is acquired and three increasing tones when home area service is acquired again.
• On any change: Alerts you with three increasing tones if there is a change in roaming service or three decreasing tones if the phone loses service.

You can restrict your phone from making a call when roaming.

From Roam Option, select Automatic (to allow roaming) or No Roaming (to disallow roaming).

Your phone can have two service accounts, or phone lines, associated with it. Each phone line has its own phone number.

From Set Phone Line, read the note and select OK and one of the phone lines.

When using one line, you cannot receive calls from the other. It would be as if the phone were “off” for that number. Your voicemail, however, still takes messages. All contacts and settings are shared for both lines.

Use Location to share your location information with network services other than emergency services (for example, 911, 111, 999 and 000) in serviced areas. This feature works only when your phone is in digital mode. You do have the option of turning off the locator to emergency services.

From Location, select one of the following:

• 911 Only: (Default) Shares your position information only with emergency services when you call your 3-digit emergency code.
• Location On: Shares your position information, in addition to emergency services.

You can set an alert to confirm the start or end of a browser session.

From Web Alert, select one of the following:

• At Start: Prompts when you start a session.
• At End: Prompts when you end a session.
• Both: Prompts when you start and end a session.
• No Prompts: Sets for no prompts.

You can set the phone to warn you before you answer or place a call while roaming.

From Roam Call Alert, select Enabled.

The phone emits a distinctive ring to indicate when you are roaming during a call. To accept or place a call while roaming, you must press 1.

With your phone locked, you can call only emergency numbers or your service provider’s customer service number. You can still receive incoming calls.

1. From Security, enter your four-digit lock code.

2. Select Lock Phone > OK and one of the following:

• On power up: Locks the phone every time you turn it on.
• Now: Locks the phone immediately.

1. From the home screen, select Unlock.

2. Enter your four-digit lock code.

You can limit the calls that can be made from your phone to emergency numbers, your contacts, and your service provider’s numbers.

1. From Security, enter your four-digit lock code.

2. Select Limit Calls and one of the following:

• No Limit: Does not limit calls.
• Limit Outgoing: Limits outgoing calls while incoming calls still work.
• Limit All: Limits both incoming and outgoing calls.

1. From Security, enter your four-digit lock code.

2. Select Erase Contacts > Yes > Yes to erase all entries from your contacts list.

Note: You cannot recover deleted information.

Change your lock code from the default.

1. From Security, enter your four-digit lock code.

2. Select New Lock Code > Yes.

3. Enter a new four-digit code.

4. Re-enter your new lock code.

Select Build Info to check your phone’s software and hardware information.

Select Icon Key to view the icons used in your phone.

From Phone Info, select User Guide to access the user guide for your phone.

Select Tools & Games from the main menu to access the following functions:

The goal of this game is to eliminate bricks arranged in levels. You send a moving ball upward using a paddle at the bottom of the screen.

1. Select Brick Attack.

2. You may see a notification, select Yes or No.

3. Select New to start the game. You have the following options:

• Use the Navigation key to move the paddle.
• Press the Back key to pause the game.
• Select Resume to restart the game.
• Select Options > Exit to exit the game.

1. From Voice Memo, select Record New.

2. Record your voice memo and select Stop when done.

3. Select Save.

If you receive an incoming call while recording a memo, the memo is saved and the incoming call screen appears.

1. From Recorded Memos, highlight a memo.

2. Select Play to play the memo or Options to access more features.

Use the Navigation key to control the playback tools displayed.

1. From Add New Event, enter a name. Scroll down to move to the next field when done.

2. Press the OK key to select an event type from the list.

3. Press the OK key to change the date, if needed.

• Scroll left or right to move between month, day, and year fields.
• Scroll up or down to change month, day, and year.

Press the OK key to save and move to the next field.

4. Press the OK key to change the time, if needed.

• Scroll left or right to move between hour, minute, and AM/PM fields.
• Scroll up or down to change hour, minute, and AM/PM.

Press the OK key to save and move to the next field.

5. Press the OK key to change the duration, if needed.

• Scroll left or right to move between hour and minute fields.
• Scroll up or down to change hour and minute.

Press the OK key to save and move to the next field.

6. Press the OK key to select a priority from the list.

7. Press the OK key to select a reminder from the list.

8. Press the OK key to select a reminder sound from the list.

1. From View Month, scroll through the month view. (Days with events are highlighted.)

2. Press the OK key to select a date.

3. Do one of the following:

• Scroll left or right to move to another date.
• Select an event.
• Scroll to a time and select Add New to create a new event.
• Select Options to access more features.

From View Day, do one of the following:

• Scroll left or right to move to another date.
• Select an event.
• Scroll to a time and select Add New to create a new event.
• Select Options to access more features.

1. From Go to Date, scroll left or right to move between month, day, and year fields.

Scroll up or down to change month, day, or year.

2. Press the OK key to select the date.

From View All Events, select an event from the list or Options to access more features.

From View Day, select Options > Go to Today to return to the current date.

From View All Events, select Options > Sort by Time to sort events by time.

From View All Events, select Options > Sort by Type to sort events by their assigned type.

From View All Events, select Options > Sort by Priority to sort events by their assigned priority.

1. From View Day, select an event.

2. At the event details screen, select Options > Edit.

3. Modify the event and select Save.

1. From View Day, select an event.

2. At the event details screen, select Options > Send > Via MMS Msg (to attach the file to a multimedia message), Via Bluetooth (to send the file to a Bluetooth-enabled device), or To Printer (to print the file on a Bluetooth-enabled device).

3. Complete the appropriate task.

1. From View Day, select an event.

2. At the event details screen, select Options > Copy.

3. Enter a new name for the event.

4. Complete the event and select Save.

1. From View Day, select an event.

2. At the event details screen, select Options > Erase > Yes.

From View Day, select Options > Erase Today’s Events > Yes to erase all events on that day.

From View All Events, select Options > Erase All Events > Yes to erase all events from the phone.

Note: You cannot recover deleted information.

From View All Events, select Options > Erase All Past Events > Yes to erase all past events from the phone.

Note: You cannot recover deleted information.

1. From Scheduler Hours, modify the start and end times.

• Scroll left or right to move between hour, minute, and AM/PM fields.
• Scroll up or down to change hour, minute, and AM/PM.

2. Select Save when done.

From Auto Erase, select an option from the list to set when to automatically erase your past events.

From Priority, select an option to set every event you create with this priority type.

From Reminder, select an option to set every event you create with this reminder setting.

From Reminder Sound, select an option to set every event you create with this reminder alert. (Scroll to listen to sounds.)

From Silent Mode, select an option to set every event you create with this silent mode.

You can set up to four alerts with your phone’s three alarm clocks and one quick alarm.

Note: The alert occurs only if the phone is on.

1. From Alarm Clock, scroll to one of the alarms and select Set.

2. Press the OK key to change the time, if needed.

• Scroll left or right to move between hour, minute and AM/PM fields.
• Scroll up or down to change hour, minute and AM/PM.

Press the OK key to save time and move to the next field.

3. Press the OK key to select a sound from the list.

4. Press the OK key to select a recurring alarm from the list, if needed.

5. Press the OK key to enter a note.

6. Select Save.

When the alarm rings, select Stop to turn off the alarm or Snooze to set the alarm to ring in another ten minutes.

1. From Alarm Clock, scroll to the quick alarm and select Set.

2. Choose a time. (A notification shows the quick alarm is on.)

When the quick alarm rings, select Off to turn off the alarm, or Reset to set the quick alarm again.

1. From Tip Calculator, enter the amount of your bill.

2. Scroll down to select the percentage you want to tip.

The total bill with tip is displayed. If you are finished, select Done. Otherwise, go on to the next step.

3. Scroll down to enter the number of people sharing the bill (or enter 1 if paying the entire bill).

4. Select Next to view the final bill.

5. Select Done when finished.

1. From Calculator, enter the first number.

2. Select a mathematical operation:

• Scroll left to multiply.
• Scroll right to divide.
• Scroll up to add.
• Scroll down to subtract.

Your selection will appear highlighted.

3. Enter the second number, and press the OK key to view the result.

4. Select Exit to return to the menu, or Options and one of the following:

• MS: Replaces the value currently stored in memory with the displayed result on the screen.
• M+: Adds displayed result on the screen to the value currently stored in memory.
• MR: Displays value currently stored in memory on the screen.
• MC: Clears currently stored value in memory.

The timer counts down for the specified time. It beeps when that amount of time has elapsed.

1. From Timer, select Set.

2. Enter the time length.

• Scroll left or right to move between hours, minutes, or seconds fields.
• Scroll up or down to change hours, minutes, or seconds.

3. Select Sound, and choose from the list to modify the sound.

4. To work the timer, select from the following options:

• Start: Begins the countdown.
• Stop: Pauses the countdown.
• Reset: Clears the timer.

When the countdown is complete, select Off to silence the alarm.

From Stopwatch, select from the following options:

• Start: Begins counting.
• Stop: Pauses counting.
• Reset: Clears the stopwatch.

Press the Back key to exit.

1. From New Memo, enter the memo.

2. Select Save.

From View Memos, select View to open a memo or Options to access more features.

1. From View Memos, highlight a memo.

2. Select Options > Edit.

3. Edit the memo, and select Save.

1. From View Memos, highlight a memo.

2. Select Options > Send as SMS.

3. Complete the message, and select Send.

If you have a phone number in a memo, you can call it.

1. From View Memos, highlight a memo.

2. Select Options > Use Number.

3. Select a number, and press the Send key.

You can lock a memo to prevent it from being edited or erased.

1. From View Memos, highlight a memo.

2. Select Options > Lock Memo.

To unlock a memo, select Unlock Memo.

1. From View Memos, highlight a memo.

2. Select Options > Erase > Yes.

From View Memos, select Options > Erase All > Yes.

Note: Selecting Erase All only erases unlocked memos.

1. From World Clock, first scroll left or right to select a time zone.

2. Check your local time and date on the first line, followed by your selected world city and its time and date.

1. From World Clock, select Options > Search City or Search Country.

2. Enter the first letter(s) of your desired city or country.

3. Select a city or country from the list.

Your Kyocera phone has the added ability to download and manage applications through BREW.

BREW brings you the full range of applications and services you have come to expect from the Internet: Email and instant messaging, real-time navigation services, group chat, games, relevant news, and much more.

You connect to the server, download applications, and then manage them as you like. When you choose an application, you have the option of choosing a demo, various limited use options, or the full version—all varying in price. If you choose a demo, BREW lets you know when it has expired. If you choose a priced version, the amount is added to your phone bill. BREW also lets you know if you are running out of memory. At that point, you can either disable an application or remove it completely.

Once applications are loaded, you can update to newer versions as they become available.

1. From BREW, select Mobileshop > Catalog. When a connection is made, a list of application types appears.

2. Select an application type. A list of applications appears. Long titles scroll left as you highlight them.

3. Select an application. A list of usages appears. There may be one or more usages available. Prices are specified for each usage.

4. Select a usage for the application. You are prompted to confirm your purchase.

5. Select Yes to confirm. The application downloads to your phone. Download times may vary.

To open the application now, select Yes. If you select No, you return to BREW, where you see a link to your new application.

From BREW, select Help to get instructions on how to run and manage your downloaded applications.

Select Media Gallery from the main menu to access the following functions:

1. From Camera Pictures, select a picture.

2. Select Send > Via EMS Msg (to attach to an enhanced message), Via MMS Msg (to attach to a multimedia message), Via Bluetooth (to send to a Bluetooth-enabled device), or To Printer (to print on a Bluetooth-enabled device).

3. Complete the appropriate task.

1. From Saved Images, select an image.

2. Select Send > Via EMS Msg (to attach to an enhanced message), Via MMS Msg (to attach to a multimedia message), Via Bluetooth (to send to a Bluetooth-enabled device), or To Printer (to print on a Bluetooth-enabled device).

3. Complete the appropriate task.

1. From Wallpapers, select a wallpaper.

2. Select Set Default.

1. From Wallpaper Shuffle, select Edit.

With no wallpapers saved, you need to add files.

2. Select Add to include a file in the shuffle, Remove to remove a file from the shuffle, or Options to access more features.

3. When finished, select Options > Done.

1. From Screensavers, select a screensaver.

2. Select Set Default.

1. From Caller IDs, select an image.

2. Select Assign.

3. At the contacts list, select a contact.

1. From Saved Sounds, highlight a sound.

2. Select Send > Via EMS Msg (to attach to an enhanced message), Via MMS Msg (to attach to a multimedia message), or Via Bluetooth (to send to a Bluetooth-enabled device).

3. Complete the appropriate task.

1. From Ringers, highlight a ringer.

2. Select Assign and choose how you want to assign the ringer.

3. Complete the appropriate task.

1. From Ringer Shuffle, select Edit.

2. Select Add to include a file in the shuffle, Remove to remove a file from the shuffle, or Options to access more features.

3. When finished, select Options > Done.

You can only edit the shuffle with at least a file added.

1. From Voice Memos, highlight a memo you have recorded.

2. Select Play.

Use the Navigation key to control the playback tools displayed.

1. From a media file list, highlight a file.

2. Select Options > Rename.

3. Enter a new name and select Save.

You can only rename unlocked files. Preloaded files on your phone are always locked.

1. From a media file list, highlight a file.

2. Select Options > Send > Via EMS Msg (to attach to an enhanced message), Via MMS Msg (to attach to a multimedia message), Via Bluetooth (to send to a Bluetooth-enabled device), or To Printer (to print on a Bluetooth-enabled device).

The options available depend on the file type.

3. Complete the appropriate task.

1. From a media file list, highlight a file.

2. Select Options > Send to Online.

1. From a media file list, highlight a file.

2. Select Options > Assign and choose how to assign the file.

3. Complete the appropriate task.

1. From a media file list, highlight a file.

2. Select Options > Lock to protect a file from being accidently erased. To unlock the file, select Options > Unlock.

1. From a media file list, highlight a file.

2. Select Options > Play.

Use the Navigation key to control the playback tools displayed.

1. From a media file list, highlight a file.

2. Select Options > Shuffle to add the file to the applicable shuffle.

1. From a media file list, highlight a file.

2. Select Options > Details to view the details such as file size or save date.

3. Select OK to exit.

1. From a media file list, select a file.

2. Select Options > Modify.

3. Select Options and an option to rotate, resize, and so on.

4. When done, select Save to save over an existing file or as a new one.

1. From a media file list, select a file.

2. Select Options > Zoom.

3. Use the Navigation key to zoom in and out.

4. Select Cancel to exit.

1. From Camera Pictures, select Options > Slideshow to play the slideshow of the files contained in the current folder.

2. Select Pause (to stop), Play (to resume), or Options (to access more features).

With Options selected, your phone automatically pauses the slideshow.

3. When you are done, select Options > Exit.

1. From a media file list, highlight a file.

2. Select Options > Erase > Yes.

You can only erase unlocked files. Preloaded files on your phone are always locked.

From a media file list, select Options > Erase All > Yes.

Note: You can only erase unlocked files. Preloaded files on your phone are always locked.

From Delete All, select Camera Pics Only > Yes to erase all files in the Camera Pictures folder.

Note: You can only erase unlocked files.

From Delete All, select Images Only > Yes to erase all files in the Images folder.

Note: You can only erase unlocked files. Preloaded files on your phone are always locked.

From Delete All, select Sounds Only > Yes to erase all files in the Sounds folder.

Note: You can only erase unlocked files. Preloaded files on your phone are always locked.

From Delete All, select Delete All > Yes to erase all files in the Media Gallery folder.

Note: You can only erase unlocked files. Preloaded files on your phone are always locked.

1. From the home screen, press and hold the Send key. The phone prompts, “Say a command”.

2. Say “Contact” and the name of the person you want to call.

The phone prompts, “Please repeat” or “Say a name” if it does not recognize the name. If the name you spoke matches a contact in the voice dial list, the phone prompts: “Name, correct?” Say “Yes” to make the call, “No” to select a similar name, or “Cancel” to cancel the phone call.

If the phone finds multiple voice tags that sound like the name you said, the phone will list the names. You will be asked to verify which name you want to call. Say “Yes” when you hear the correct name. Say “No” when you hear an incorrect name.

3. Press the End key to end the call.

1. From the home screen, press and hold the Send key. The phone prompts, “Say a command”.

2. Say “Dial Number” and then speak the digits of the number you want to call. If you pause, the phone prompts you, “Did you say ” or “Say a number” if it does not recognize the name. Say “Yes” to make the call, “No” to cancel the phone call.

3. Press the End key to end the call.

1. From the home screen, press and hold the Send key. The phone prompts, “Say a command”.

2. Say the name of the menu item you want to access or say “Shortcuts” to view a list of menu items. The phone prompts, “Say one of the shortcuts”.

3. Say the name of the menu item you want to access.

1. From the home screen, press and hold the Send key. The phone prompts, “Say a command”.

2. Say “Find Contacts”. The phone prompts, “Say a name”.

The phone prompts, “Please repeat” or “Say a name” if it does not recognize the name. If the name you spoke matches a contact in the voice dial list, the phone prompts: “Name, correct?” Say “Yes” to display the contact, “No” to select a similar name, or “Cancel” to cancel the search.

Note: You can only search for contacts that are in the voice dial list.

Before requesting support, please try to reproduce and isolate the problem. When you contact the Customer Care Center, be ready to provide the following information:

• The name of your service provider.
• The actual error message or problem you are experiencing.
• The steps you took to reproduce the problem.
• The phone’s mobile equipment identifier (MEID).