KUSSMAUL PUMP PLUS 1000 PLC 091-215-12-PP (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL PUMP PLUS 1000 PLC 091-215-12-PP (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL- PUMP PL-US nooo Pl-C AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays pUMP p LOS 1000 PLC . Insob MODE’ # : INPUT: 120 Vole, eo Hz, 3.5 Amps OUTPUT BATTERY 1 and e: 15 or 1B Amps OUTPUT BATTERY SAVER: 3 Amps File: IM_OBI -215-12-PP_revC.indd Rev: C Revisd By: SO, PGB, Date: 05-13-201 e 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com 1 YEAR WARRANTY ON PUMP a YEAR WARRANTY 0N CHARGER KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS couNT scan using your mobile device for more information Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** IMPORTANT SAFETY INs-rnucT/0Ns l. PERSONAL PRECAUTIONS: 1. 2. 3. 4. 5. 6. 7. 8. 9. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. Wear complete eye and clothing protection. Avoid touching your eyes while working near a battery. If battery acid contacts skin or clothing, wash immediately with soap and water. If battery acid enters the eye, immediately flood eye with cold running water for at least 10 minutes and get medical attention immediately. NEVER smoke or allow a spark or flame in the vicinity of the battery or engine. Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit the battery or other electrical part and cause a fire or an explosion. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery, when shorted, can produce a current sufficient to weld a ring or the like metal causing a severe burn. Use the battery charger for charging gel-cell, AGM and flooded lead-acid batteries only. Do not use the charaer for charging dry-cell batteries that are commonly used with home applications. These batteries may burst and cause inu to WARNING RISK OF to Pr0PertY. Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. II. CHARGER PRECAUTIONS: 1. 2. 3. 4. 5. 6. 7. 8. NEVER charge a frozen battery. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Do not operate the charger with a damaged cord or plug; replace them immediately. Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged. Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock and fire. To reduce the risk of electric shock, disconnect the charger from the AC source before attempting any maintenance or cleanin LOCATION OF CHAR8ÉR The charger should be mounted on a wall, vehicle floor, ventilated compart- ment or other suitable surface as close to the batteries to be charged as possible. Do not block the char- ger’s fan or air intakes. Do not mount the charger directly over the batteries as fumes may cause exces- Sive corrosion. The area should be well ventilated and free from excessive moisture, exhaust manifolds, and battery fumes. For maximum performance, the charger should not be located in an area of extreme high temperature. The charger is not waterproof. Do not mount the charger where there is a possibility of water entering the unit. Evidence of water entry into the charger will void the warranty. CAUTION: Do not attempt to increase battery bank capacity by splitting the output of one of the banks with a diode-type battery isolator. The diode isolator lowers the charger voltage and results in under- charging the batteries connected to it. If additional capacity is required it is preferable to add another isolated or parallel battery. Ill. GROUND AND AC POWER CORD CONNECTION 1. 2. 3. 4. The charger should be grounded via the AC power connection to reduce the risk of electrical shock. The charger must be plugged into or wired to an outlet that is an over-current protected 3 prong outlet. Alternatively, it may be routed through a separate dedicated fuse or circuit breaker on an AC distribution panel with proper earth/safety ground. All wiring shall comply with UL recommendations, NEC or NFPA standards and local ordinances. Never alter the AC cord or plug if provided. Any modification of the cord must only be done by a qualified electrician. Improper cord/outlet connection may result in a risk of elec- trical shock. Observe color coding of the AC wiring as follows: Black. AC Hot or LINE (fused) White… AC Neutral . AC Ground (safety/earth) CAUTION: 230 VAC applications only): If AC input is provided from a source consisting of two HOT or LINE leads phase-to-phase 230 VAC input voltage); an external fuse or circuit breaker must be used to protect both hot leads. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 3 ****** INTRODUCTION The Pump Plus 1000 PLC with Parasitic Load Compensation (PLC) is a compact, microprocessor controlled, completely automatic, single channel battery charger designed for vehicles with a single battery system. The PLC charger is designed to withstand the shock and vibration encountered by vehicle mounted equipment. The Pump Plus 1000 PLC is designed to power a 091-9-12V air compressor. A DIP switch is provided to select full- time compressor operation (DC position) or only while AC power is applied (AC position). FEATURES l. PUMP PLUS 1000 PLC BATTERY CHARGER Electronic remote sensing of true battery voltage, eliminates the need for sensing wires Automatic current limiting • Pump output with AC or DC mode dip switch • Built-in Battery Saver output • Accommodates Lead-Acid, Gelled Electrolyte, AGM and Odyssey@ battery types • Configurable for 3-Step or Float Charging 3 hour Safety Timer while in 3-Step mode Adjustable Parasitic Load Compensation (0-12 amperes) • Power “ON” LED indicator System Status LED indicator Whisper quiet cooling fan II. CHARGE CONTROLS & ELECTRONIC REMOTE SENSING Pump Plus 1000 PLC contains a precision voltage controller to maintain the battery’s charge. Automatic electronic remote sensing measures the true battery voltage, eliminating the need for additional sense wires. The output current of the charger is a series of pulses whose frequency is determined by the power line fre- quency. The Pump Plus 1000 PLC measures the battery voltage during brief intervals between pulses while no charge current is flowing. The battery voltage is compared to a standard and any error is detected and used to control the charger output at the desired level. There is no “trickle charge”, therefore, no danger of overcharging and water boil-off. Ill. AUTOMATIC CURRENT LIMITING Some battery chargers can be overloaded due to the high charging current required when batteries are se- verely discharged. The Pump Plus 1000 PLC contains an automatic current limiting circuit. This circuit limits the output current to the rated 15 amperes when charging a deeply discharged battery or if the starter cranks the engine while charging. The current limiter thus eliminates the need for an ignition interlock circuit. lv. PLC – PARASITIC LOAD COMPENSATION This new feature is designed specifically to meet the heavy duty requirements of emergency vehicles. Most emergency vehicles have many parasitic loads on their systems (flash lights, gas detectors, computers, monitoring systems and other items) that can trick a standard 3-step charger into over charging the batteries. Parasitic load compensation allows you to input the total number of parasitic load amps on the vehicle. The charger will then shift the absorption stage set-point so the battery voltage will drop to the float voltage when the desired current is reached. In short the parasitic loads are invisible to the charger. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 3

****** Page 4 ****** WIRING AND SWITCH SETTINGS l. BATTERY CHARGER WIRING INSTRUCTIONS 0-5 5- 10 1. 2. 3. 4. 5. 6. 7. Refer to Installation Wiring Diagram I & II. Refer to Wiring Specifications to determine the recommended wire size and maximum lengths-Using a smaller gauge may cause overheating of the terminal. Additional information is available upon request if longer, larger wiring is required. Torque DC output connector. Refer to Specifications. Set the front panel switches for the appropriate battery type, charge method, safety timer value, battery saver mode and parasitic load requirement. Refer to Sections Ill, IV, V, VI and VII. Double check all wiring and switch settings before applying AC power to input terminal. Apply AC power (shoreline power) to input terminal and observe that the charger is operating. Verify that the battery voltage appears at the charger output terminals. II. WIRING SPECIFICATIONS Length of Wire to Battery (feet) Battery Charger Connections Wire # Gauge (awg) ä 14 o u 14 14 16 14 o 12 12 16 12 o u 10 10 16 * Consult factory if length of wire to battery is longer than 20 feet Ill. BATTERY TYPE SELECTION SWITCHES Switches 1 and 2 should be set to match the battery chemistry. Lead-Acid – Both switches down (off) – factory default setting Gelled Electrolyte (Gel Cell) – Switch 1 down (off) and Switch 2 up (on) AGM – Switch 1 up (on) and Switch 2 down (off) Odyssey@ – Both switches up (on) W. FLOAT / 3-STEP CHARGE MODE SELECTION SWITCHES Switch 3 should be set for the desired charging method, Float or 3-Step. When in 3-step mode, the safety timer period is 3 hours. The safety timer period begins when AC power is applied to the charger. The absorption phase of 3-step charging terminates when the safety timer expires, or when the PLC threshold setting is reached. If no PLC settings are set, the threshold is 0.5A. The charger then switches to, and remains in, float mode while AC power is applied. Float Charge Only — Switch 3 down (off) – factory default setting 3-Step with 3 Hour Safety Timer – Switch 3 up (on) 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 4

****** Page 5 ****** V. AUTO PUMP MODE SELECTION SWITCH Switch 4 controls the Auto Pump operating mode. AC — Switch 4 down (off) factory default setting. The compressor will operate only when AC power is applied to the battery charger. DC — Switch 4 up (on). The compressor will operate when the AC power is on or off. It is powered by the charger while AC power is applied to the charger and from the vehicle’s battery when no AC power is applied. VI. BATTERY SAVER SWITCH A low ripple, current limited, 3 ampere Battery Saver is built into the charger. When connected as shown in the installation wiring diagram, loads on the battery such as radios and rechargeable hand lights are automatically switched to the Battery Saver when power is applied to the charger. The Battery Saver allows more efficient charging by removing these loads from the battery. Switch 5 enables the Battery Saver when set in the up (on) position. If it is not required, turn the Battery Saver off by setting switch 5 down (off) position. This is the factory default setting. A Battery Saver filter is not required. WHEN A BATTERY SAVER OVERLOAD OCCURS: a. Remove the loads for approximately two minutes b. Reduce the load to 3 amperes or less c. Reapply the load to the Battery Saver No fuses are required or provided as the Battery Saver contains an automatic circuit breaker. VII. PARASITIC LOAD COMPENSATION SWITCHES (3-Step mode only) Switches 6, 7 and 8 should be set to match the parasitic load on the battery (excluding any Battery Saver load). These switches control the point at which the charger will terminate the absorption phase of the 3-step charging cycle. The possible settings are 0, 1, 2, 4, 6, 8, 10 or 12 amperes. If there are no parasitic loads on battery 1, or if they are all are on the Battery Saver, then set these three switches to the down (off) position. This is the factory default setting. VIII. REMOTE BATTERY CHARGE CONDITION INDICATOR (Standard equipment) This remote indicator shows the charge condition of each battery in 10 levels from “LOW CHARGE” to “FULLY CHARGED”. This device indicates a defective battery when the bar graph does not rise to the “FULLY CHARGED” level after an extended period of charging. NOTE: If the battery is being charged with an external load of 1.5 to 4 amperes across its terminals, the bar graph may move down 1 or 2 levels. This does not indicate a defective battery. To avoid this, connect all external loads to the Battery Saver terminals. Loads connected to the Battery Saver will be powered by the Battery Saver power supply when the AC power is “ON”, or they will be connected to the battery when the AC power is “OFF”. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 6 ****** ON OFF SWITCH SHOWN IN OFF POSITION Legend on front panel of charger Bd LEAD BFLOAT BAC BATTERY TYPE sw/TcH SETTINGS This is what the dip switch should look like when setting it to the legend on the front panel of the charger, 012345678 $ CTS 206-9 $406 12345678 B OFF BBB 0 AMPS BATTERY PARASITIC LOAD SAUER COMPENSATION CHARGE MODE AUTO PUMP NOTE” The charger is shipped with all DIP switches in the down position- This configuration is for Float Charging ofa Lead-Acid battery with Battery Saver and Parasitic Load Compensation turned off. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 7 ****** INSTALLATION WIRING DIAGRAM l. FOR STANDARD BAR GRAPH DISPLAY, 091-199-001 or OPTIONAL DELUXE STATUS CENTER, 091-194B-lND Wiring Diagram shown is for a 10 foot installation SYSTEM Remote Indicator 1 – RED 20AWG 2 – BLACK 20AWG 3 – WHITE 20AWG 4 – GREEN 20AWG NOTE: Pin 1 of indicator must go to Pin 1 of Remote Display on charger. Pin 2 of indicator must go to Pin 2 of Remote Display on charger, and so forth. Check connections and color of wires before plugging-in. Auto Pump Air Compressor 0 1 2 3 4 INDICATOR PLC REMOTE PUMP PLUS 1000 PLC 12345678 r—-ZJ LEAD R FLOAT RAC ‘O-AUTO GEL e a-STEP 1 AMPS nun ? AMPS 5NlTCH MOOE PUMP SAUER IN OÆFOSITION BATTERY TYPE 1 ö 2 filälfiläläll O II BLK BLK RED RED Pressure Switch m Chassis Ground m BLACK (14AWG) O O RED (12AWG o O o Accessories CAUTION Connect wires to charger Connect wires to battery 3. Apply AC power Caution instating battery wires tratt tm ChasstS @vet 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com WIRE SIZE CHART KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS couNT 10 AMPS 12 Arvps PARASITIC LOAD MIMPE,NSAT/ON 40 Amp fuse or Waterproof Circuit Breaker Kussmaul Part #: 090-0040-0 Install near the battery. O Battery Saver Loads (3 amps max.). When the charger is disconnected from 120 volts AC the Battery Saver loads automatically are connected to battery #1. Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 7

****** Page 8 ****** II. FOR OPTIONAL WATERTIGHT DELUXE STATUS CENTER, 091-194B-lND-WT-XX Wiring Diagram shown is for a 10 foot installation t – RED 20AWG 2 – BLACK 20AWG 3 – WHITE 20AWG 4 GREEN 20AWG mae;atM NOTE: Pin 1 of indicator must go to Pin 1 of Remote Display on charger. Pin 2 of indicator must go to Pin 2 of Remote Display on charger, and so forth. Check connections and color of wires before plugging-in. Auto Pump Air Compressor 0 m BLK BLK RED Pressure Switch 1 • RED 20AWG O 2- BLACK 20AWG 3- WHITE 20AWG 4 – GREEN 20AWG 1 2 4 INDICATOR PLC REMOTE PUMP PLUS 1000 PLC ‘3STEP g DC CHARSE MOOE BATTERY TYPE I PUMP ö 2 o o 1234567B OFF O -AUTO 1 AMPS ON UTTER* AMPS 12 NPS tono COMPENSATION SYSTEM POWER 40 Amp fuse or Waterproof Circuit Breaker Kussmaul Part 090-0040-0 Install near the battery. O LU Chassis Ground ffgg m BLACK (14AWG) O RED (12AWG) O CAUTION I. Connect wires to eh*qer 2. Connect wires to battery 3. Apply AC power Caubm •nstalhno battery wges into front A screwdriver the chaws cogen 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com Accessories WIRE SIZE CHART KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Battery Saver Loads (3 amps max.). When the charger is disconnected from 120 volts AC the Battery Saver loads automatically are connected to battery #1 Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 9 ****** SPECIFICATIONS Input Power: 120 Volt, 60 Hz, 3.5 amperes Input Fuse: 6 ampere, fast blow Output Power – Bat : 15 amperes max (18 amperes if Battery Saver is turned off) Battery Type Lead-Acid Gelled Electrolyte AGM Odyssey@ Float V DC 13.25 13.50 13.50 13.60 Absorbtion V DC 14.00 14.25 14.40 14.70 Output Power – Battery Saver: 13 Volts DC, 3 amperes max Pump Output: 12 Amp Max Remote Sensing: Electronic, sense wires not required LED Status Indicators: Power: Green LED, Indicates 120 VoltAC power applied System: Yellow LED: Fast Flash (5 times per Second) indicates battery reverse polarity Slow Flash (once per second) indicates no battery is connected Solid On indicates charger is in current limit (normal operation) Solid Off indicates normal operation Brief Flash (once every 2 seconds) indicates 3-step boost mode operation Cooling Fan: The whisper quiet cooling fan exhausts air from the rear of the charger. When the Battery Saver is enabled, it is continuously on while AC power is applied to the charger. It turns on at 4 amperes of output current and turns off at 3 amperes when the Battery Saver is disabled. Torque: DC Output Connector: 15 in. lbs. Remote Display Options: Bar Graph Display, Deluxe Status Center or Watertight Status Center Output Waterproof Circuit Breaker (Optional): Bat 1 – 40 amperes, P/N: 090-0040-0 Output Buss Bar (Optional): 5 Studs, PIN: 002-3595-5 Weight: 11 pounds 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 10 ****** OUTLINE DRAWING 5.35 7.00 1.175 5.90 3/16″ DIA. 4.725 9.35 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 10

****** Page 11 ****** OPTIONAL ACCESSORIES l. GRAPH DISPLAY, MODEL 091-199-001 10-Segment LED display indicate the “state of charge” and the general condition of the batteries II. DELUXE STATUS CENTER, MODEL 091-194B-lND Indicator has a digital voltage and ampere display 5 segment bar graph display indicates output current 4 LED’s to show the condition of the batteries Au-ro CHARGE’ O PUMP nus CENTER 1360 F. Ill. WATERTIGHT DELUXE STATUS CENTER, MODEL 091-194B-lND-WT-XX Indicator has digital voltage and ampere display 5 segment bar graph display indicates output current 4 LED’s to show the condition of the batteries Indicator is housed in a watertight bezel Bezel is available in 6 different colors, Red, White, Blue, Yellow, Gray, and Black Specify color choice when ordering W. 40 AMP WATERPROOF CIRCUIT BREAKER, MODEL 090-0040-0 Combines switching and circuit breaker function Compact size and surface mount configuration Protects high amperage circuits Latch arms resets breaker after overload Cannot be held in ON position if short remains on circuit Waterproof – Ideal for truck applications 5 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT PUMP PLUS STAIus Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 11

****** Page 12 ****** INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POI-ICY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kuss- maul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. Members of fire and emergency Manufacturers and Service Associatio,fi Members of National fire Protection Members of Eire Apparatus Manufacturers Made in, USA 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com Association Association NFPA’ KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT AMA Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.