Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL EURO CHARGE 11HO 091-11HO (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** FILE: 091-1 lho-12.p65 4-24-2002 REV. B INSTRUCTION MANUAL AUTO CHARGE 1 1 HO AUTOMATIC BATTERY CHARGER MODEL #091-1 1 HO NOTE : This charger is designed for vehicles with dual batteries and negative ground. 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC- 170 CHERRY AVE. , WEST SAYVILLE, N.Y. 11796 TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826

****** Page 2 ****** INTRODUCTION The Auto Charge 1 IHO Battery Charger is a compact completely automatic charger designed for installation on vehicles with two batteries. Two separate charging circuits monitor the charge requirements of each battery and charge each battery individually. A current limiter protects the charger when charging deeply discharged batteries by limiting the total charger output current. An ammeter provides continuous indication of the charger output. Construction of the Auto Charge 11 HO is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates com- pletely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc., are automatically supplied with current by the charger. INSTALLATION The Auto Charge 1 IHO Automatic Battery Charger should be installed in an area with adequate ventilation. 1. Mount the charger using the four holes provided for this. 2. Connect the wiring from the batteries to the Output Terminal Strip. 3. Double check all wiring before proceeding. 4. Wire the A.C. power to the A.C. Input Terminal Strip. 5. Pilot light will light to show that the charger has power. page 1

****** Page 3 ****** INSTALLATION WIRING DIAGRAM o FUSE O INPUT A.C. Input Power Line Neutral Ground Optional Bar-Graph Indicator 091-11-127 o POWER O O o BATI O -L OUTPUT BAT2 Chassis Ground o O REMOTE Chassis Ground e//0Lv &/ect Optional Economy Indicator 091-11-102-xx Chassis Ground IMPORTANT: Charger output wire size is 12 awg. Wire size is for a maximum length of 20 feet. If wiring is to be longer, larger wiring is required. Additional information is available on request. page 2

****** Page 4 ****** SPECIFICATION & OUTLINE SPECIFICATION CHART SPECIFICATIONS: Input: see chart Output: see chart Output Current: see chart Charge Indicator: 0-25 amps 5% Weight: 23 lbs 6.75 MODEL # AvlPS VOLTAGE VOLTAGE OUTPUT INPUT 091-11 HO-6 091-111-10-12 091-11 HO-24 091-11 HO-6-220 091-11 HO-12-220 091-11 HO-24-220 UTO CHARGE 12.00 4.75 9/32′ DIA. 4 HOLES 4.25 20 20 11 20 20 11 120 A.C. 120 A.C. 120 A.C. 220 A.C 220 A.C 220 A.C 12.75 OUTLINE DRAWING OUTPUT 6 12 24 6 12 24 page 3

****** Page 5 ****** INSTALLATION Date Installed Installed By Vehicle Identification Vehicle Owner RECORD & WARRANTY WARRANTY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and [or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees others. page 4







Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.