KUSSMAUL AUTO CHARGE 11HO PIM 091-11HO-PIM (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL AUTO CHARGE 11HO PIM 091-11HO-PIM (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** BOOK# -1 1 HO-PIM-I INSTRUCTION MANUAL AUTO CHARGE PIM AUTOMATIC BATTERY CHARGER MODEL NOTE : This charger is designed for vehicles with dual batteries and negative ground. INPUT IS voles, 50/60 Hz, 4 amps a YEAR WARRANTY m KUSSMAUL ELECTRONICS CO., INC. 1 70 CHERRY AVE. , WEST SAYVILLE, N.Y. 1 1 TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826

****** Page 2 ****** INTRODUCTION The Auto Charge 1 1 HO-PIM Battery Charger is a compact completely automatic charger designed for installation on vehicles with two batteries. An internal charge divider charges both batteries simultaneously while maintaining battery isolation. Remote sensing permits long lines between the charger and the batteries by compensating for the voltage drop in the charging wires. An ammeter provides continuous indication of the charger output. Construction of the Auto Charge 1 1 HO-PIM is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates com- pletely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc., are automatically supplied with current by the charger. Any 120 volt loads when plugged into the GFI on the Auto-Charge 11 HO-PIM will be protected from ground faults. A separate lever operated circuit breaker protects the GFI connected loads. This circuit breaker may also be use to disconnect these loads from the line. The fuse on the Auto-Charge 1 1 HO-PIM protects the charger only. INSTALLATION The Auto Charge 1 1 HO-PIM Automatic Battery Charger should be installed in an area with adequate ventilation. A power cord is supplied for connection to 115 volts 50/60 Hz. 1 . Mount the charger using the four holes provided for this. 2. Connect the wiring from the batteries to the Output Terminal Strip. Spade lugs that have been securely crimped, or soldered, should be used. 3. Double check all wiring before proceeding. 4. Wire the A.C. power line cord to 115 volts. 5. Pilot light will light to show that the charger has power.

****** Page 3 ****** INSTALLATION WIRING DIAGRAM O B AMP O Chassis Ground O O POWER AUTO CHARGE 11 HO-PIM r.-………………-pos-…………………-1 SENSE COMI BATI BAT2 1 IND I Chassis CONNECTION COM BAT 1 BAT 2 SENSE SENSE WIRE SIZE CHART DEFINITION NEGATIVE CHARGING LEAD FOR BATTERIES POSITIVE CHARGING LEAD FOR BATTERY # 1 POSITIVE CHARGING LEAD FOR BATTERY # 2 NEGATIVE VOLTAGE SENSE LEAD. DETECTS VOLTAGE POSITIVE VOLTAGE SENSE LEAD. DETECTS VOLTAGE ITEM BATTERY COMMON BATTERY BATTERY NEGATIVE SENSE POSITIVE SENSE Ground WIRE SIZE 12 AWG 12 AWG 12 AWG 16 AWG 16 AWG O IMPORTANT: Wire size is for a maximum length of 20 feet. If wiring is to be longer, larger wiring is re- quired. Additional information is available on request. NOTE: Sense leads are shown con- nected to battery #1 but may be connected to either battery at the installers option. The sense leads however must be connected for the charger to operate. The charger does not require a 2 battery vehicle to function properly. For single bat- tery vehicles connect to battery #1.

****** Page 4 ****** SPECIFICATION e OUTLINE SPECIFICATIONS: Input: 120volts 50/60Hz, 4 amps Fuse: 3 amp Output: for 12 volt batteries Output Current: 0-20 amps Charge Indicator: 0-25 amps 5% Weight: 23 lbs 6.75 u•ro CHARG 12.00 4.75 9/32″ DIA. 4 HOLES 4.25 12.75 OUTLINE DRAWING

****** Page 5 ****** INSTALI-ATION e WARRANTY Date Installed Installed By Vehicle Identification Vehicle Owner WARRANTY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and [or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.