KUSSMAUL AUTP-PUMP 12V HP-VER 091-9-12V-HP-VER (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL AUTP-PUMP 12V HP-VER 091-9-12V-HP-VER (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL AUTO-PUMP@IZV HP-VER 1 HIGH OUTPUT AIR COMPRESSOR SYSTEM FOR VERTICAL MOUNT ONLY MODEL # : File: oen -9-12V-HP-VER revA Revised By: PSS/JRN Date: a-25-2017 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com INPUT : 10-15 vole, 11 amp OUTPUT : les PSI MAXIMUM YEAR WARRANTY KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** INTRODUCTION The Auto-Pump Air Compressor system is a compact electric motor operated single cylinder air compressor designed specifically for installation on vehicles with air brakes. During long idle periods of the vehicle when even the slightest seepage can cause an air brake sys- tem pressure to drop below the brake lockup pressure, the Auto Pump automatically starts to maintain the pressure. The unit also has aN automatic water separator that drains the water from the separator bowl whenever the pump is cycled. The Auto Pump motor is directly coupled to the compressor section eliminating all belts and pulleys assuring long life and reliable operation. A heavy duty pressure switch is ad- justed to start the compressor when the system pressure drops below 105 psi and stops the compressor when 125 psi is attained. The start up pressure is field adjustable – the pressure differential between start up and stopping is fixed. Please read and follow the installation instructions carefully. The Auto Pump requires no routine maintenance. A careful installation will assure years of trouble free operation. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 3 ****** CAUTION NO CONDENSATE on WATER MUST BE ALLOWED TO ENTER on ACCUMULATE IN THE OUTPUT OF THE AUTO PUMP. ROUTE OUTPUT PRESSURE LINE DOWNWARD FROM AUTO PUMP TO PERMIT MOISTURE -ro DRAIN AWAY. WATER IN THE PUMP OUTLET WILL INDUCE FAILURE WATER DAMAGE WILL VOID WARRANTY FOR VERTICAL- MOUNT ONLY THIS MODEL 091-9-12V-HP-VER IS FOR VERTICAL MOUNT ONLY. FOR HORIZONTAL MOUNTING USE MODEL 091-9-12V-HP-HOR. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 3

****** Page 4 ****** VEHICLE TUBING INSTALLATION 1 2. 3. 4. 5. 6. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt. The system may be connected to any point in the vehicle’s air system. Mount the air compressor in a vertical position as shown. CAUTION no condensate or water must be allowed to enter or accumulate in the output of the Auto Pump. Route output pressure line downward from Auto Pump to permit moisture to drain away. Water in the pump outlet will induce failure. All connection for air lines are 1/4″ NPT. Use Teflon tape, or equivalent on all connections to insure no leakage of air. The recommended installation of the Auto Pump air compressor system is shown below. Mount the air compressor. Connect a suitable piece offlexible tubing from the outlet port of compressor to the air tank. (Tubing and connectors are not supplied.) 7. An optional Mounting Plate 091-9-12V-HP-H, is available to reduce any vibration and noise from Auto Pump and to simplify pump mounting. NOTE: Compressor must be mounted above air tank to assure that moisture will flow away from compressor. The Flow of Any Moisture Y Air Pressure System Note: make sure the Auto Pump is mounted vertical. Auto P mp Automatic drain 1/4″ NPT Outlet Port Air Line THIS PUMP IS FOR VERTICAL MOUNT ONLY Optional Mounting plate 091-9-12V _HP_H Truck Body 4

****** Page 5 ****** VEHICLE WIRING INSTALLATION 1. 2. 3. 4. 5. 6. Remove cover of the Pressure Switch on the Auto Pump. Wire the pressure switch to the battery and a good chassis ground, use #14 AWG WIRE MINIMUM. Reinstall cover of Pressure Switch. The compressor is calibrated to cut-in at 105 PSI and cut-outat 125 PSI . For highercut-in and cut-out, turn the range nut clockwise. To lower cut-in turn range nut counterclockwise. Do not exceed 135 PSI. 091-9-12V-HP-VER AUTO PUMP can be wired to a positive or negative system vehicle. Optional switch and fuse can be installed as shown (use 20 amp rated switch and 15 amp (SLO-BLO fuse). Note: make sure the Auto Pump is mounted vertical. II o o THIS PUMP IS FOR VERTICAL MOUNT ONLY CAUTION Observe Correct polarity connections red lead to motor MUST be positive Pressure Switch Range Nut -12 1/OLrs 1/O{rs Optional Switch 15 AMP CIRCUIT BREAKER Optional Fuse 9 COMPRESSOR OUTPUT IS 135 PSI MAXIMUM. DO NOT EXCEED 135 PSI OR YOU WILL VOID WARRANTY.

****** Page 6 ****** TEMPLATE AUTO PUMP 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com 7/32″ DIA. HOLE 3 PLACES 1.75″ 3.50″ ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 7 ****** SPECIFICATIONS Input Voltage: 10 – 15 Volts DC Input Current: 11 Ameres Max Compressor Output: .30 SCFM @ 80 PSI, .35 SCFM @ 60 PSI, 0.80 CFM @ OPEN FLOW Temperature Range: OC to 43C (meets NFPA1901 2016 4.14.3) Motor Horsepower: .10 HP Motor Type: Permanent Magnet Pressure Switch: Set to 105 PSI Cut-in, 125 PSI Cut-out (+/- 5 PSI) Switch Differential: 18 PSI Nominal Outlet Connection: 1/4 NPT, Female Weight: 10 pounds OUTLINE DRAWING 1/4 NPT OUTLET 1/4 NPT INLET 4.63 9 23 #10-32 UNF-2B THRU 2.12 2x 3.50 a #10-32 UNF-2B THRU 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 7

****** Page 8 ****** ACCESSORIES 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com MOUNTING PLATE MODEL # 091 -9-1 2V-HP-H FOR SIMPLIFIED MOUNTING KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 9 ****** INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POLICY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kuss- maul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. Members of Fire and Emergency FEMS Manufacturers and Service Association Members of Fire Apparatus Manufacturers @ Association NFPA Made in USA 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT AMA Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.