Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL AUTO CHARGE 12 HO DV 091-170-DV-24 (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** File: DBI -1 70-dv-xx nev b. pmd Rev: b, Date: a-an -1 0 INSTRUCTION MANUAL AUTO CHARGE HO OV AUTOMATIC BATTERY CHARGER MODEL #091-170-DV-xx NOTE : This charger is designed for vehicles with a single battery system a YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INc. 1 70 CHERRY AVE. , WEST SAYVILLE, N.Y. 1 796-1 221 Phone: 631-567-0314 Toll Free: 800-346-0857 Fax: 631-567-5826 Web: kussmaul.com E-Mail: sales@kussmaul.com

****** Page 2 ****** INTRODUCTION The Auto Charge 12HO Battery Charger is a compact completely automatic charger designed for installation on vehicles with a single battery system. The patented “sample & hold” circuit is utilized to detect the battery voltage via the charging cables. An ammeter provides continuous indication ofthe charger output. Construction of the Auto Charge 12HO is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates completely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc., are automatically supplied with current by the charger. INSTALLATION The Auto Charge 12HO Automatic Battery Charger should be installed in an area with adequate ventilation. A power terminal is supplied for connection to AC. 1 . Mount the charger using the four holes located in the front and rear of the charger. 2. Connect the wiring from the battery to the Output Terminal Strip. 3.Connect the wiring to the batteries. Ring lugs that have been securely crimped or soldered should be used. 4. Double check all wiring before proceeding. 5.Check the position ofthe Voltage Selector Switch and wire the VAC input power line to the power source. 6. Pilot light will light to show that the charger has power.

****** Page 3 ****** INSTALLATION WIRING DIAGRAM CAUTION: DISCONNECT SUPPLY BEFORE FUSE SERVICE o FUSE o 1 15 VAC, 50/60Hz Input Power Line Neutral Ground AWG 16 MINIMUM Optional Bar-graph Indicator 091-39-022 o O PCJWE-R O o o RE-MCJTE 12 AWG MINIMUM IMPORTANT: Wire size is for a maximum length of 20 feet. If wiring is to be longer, larger wiring is required. Additional information is available on request. NOTE:Do not apply 230 volts to the charger with the selector switch in the 1 1 5 volt position serious damage may result.

****** Page 4 ****** OUTLINE SPECIFICATIONS: Output Model Number Voltage 091-170-DV-12 12 Vdc 091-170-DV-24 24 Vdc 12.00 Output Current 20 Am s 12 Am s Input Voltage 115 / 230 vac, 50/60 Hz 115 / 230 vac, 50/60 Hz 6.75 4.75 Input Current 4/2 Am s Current Meter 25 Am s 15 Am s 12.75 Input Output Fuse Fuse 8 Am s 40 Am s 4 Am s 24 Am s Weight 16 lbs 16 lbs 9/32″ DIA. 4 HOLES 4.25 OUTLINE DRAWING

****** Page 5 ****** INDICATOR INSTALLATION 1 Locate Indicator in a convenient place on the vehicle. 2. Place the template in position and center punch in 4 places. 3. Drill holes as shown 4. Cut out square hole. 5. Connect wiring to charger in accordance with the instructions in the charger installation instructions. 6. Install as shown. 7. Insert (4) #8-32 screws supplied and tighten. (CAUTION: Do not over tighten because you will bend the plastic bezel and break the watertight seal). 8-32 SCREW INDICATOR GASKET 3/1 DIA. 4 HOLES CUT OUT 2 1/1 x 3 1/21 HOLE TEMPLATE 3.900 TRUCK WALL #8-32 HEX NUT LOCK & FLAT WASHER o. 150 2 375 0.200 Hole Template may not be to Scale, please check dimensions before using. File: nd.cdr rev C 3-31 -l O do not shrink this art work

****** Page 6 ****** INSTALLATION e WARRANTY Date Installed Installed By Vehicle Identification Vehicle Owner WARRANTY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and /or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees others.







Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.