KUSSMAUL AUTO CHARGE 11DV 091-11-DV (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL AUTO CHARGE 11DV 091-11-DV (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL AUTO CHARGE 1 IDV AUTOMATIC BATTERY CHARGER 1 .15. NOTE : This charger is designed for vehicles with dual batteries and negative ground. MODEL # : INPUT: 115 or ego vole, 50/60 Hz, e Amps File: 091-1 IDV-I Date: 08-30-05 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com OUTPUT: 11 Amperes D.C. 3 YEAR WARRANTY KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** INTRODUCTION The Auto Charge 1 1 DV Battery Charger is a compact completely automatic charger designed for installation on vehicles with two batteries. An internal charge divider charges both batteries simultane- ously while maintaining battery isolation. Remote sensing permits long lines between the charger and the batteries by compensating for the voltage drop in the charging wires. An ammeter provides continuous indication of the charger output. Input power may be either 115 volts or 230 volts . A voltage selector switch is provided on the end panel near the output terminal strip. Construction of the Auto Charge 1 1 DV is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates completely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc., are automatically supplied with current by the charger. INSTALLATION The Auto Charge 1 1 DV Automatic Battery Charger should be installed in an area with adequate ventilation. A power cord is supplied for connection to 115 or 230 volts 60 Hz. 1. 2. 3. 4. 5. 6. Mount the charger using the four holes provided for this. Connect the wiring from the batteries to the Output Terminal Strip. Spade lugs that have been securely crimped, or soldered, should be used. Connect the wiring to the batteries. Ring lugs that have been securely crimped, or soldered, should be used. Double check all wiring before proceeding. Wire the A.C. power line cord to 115 or 230 volts. Pilot light will light to show that the charger has power. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS counr Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 3 ****** INSTALLATION WIRING DIAGRAM 115 or 230 voltage se- lector switch. NOTE: Do not apply 230 volts to the charger with the se- lector switch in the 115 volt position serious dam- age may result o 3 AMP FUSE INPUT A.C. Input Power Line Neutral Ground OUTPUT BATI BAT 2 Chassis Ground Optional Bar-graph Indicator 091-11-127 O POWER o REMOTE Chassis Gr und Chassis Gr und Optional Economy Indicator O o 091-1 1-102-XX IMPORTANT: Charger output wire size is 14 awg. Wire size is for a maximum length of 20 feet. If wiring is to be longer, larger wiring is required. Additional information is available on request. 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 3

****** Page 4 ****** SPECIFICATION SPECIFICATIONS: Input: 115V or 230V 50/60Hz, 2 amps, switch selectable Output: see chart Output Current: see chart Charge Indicator: 0-15 amps 5% e OUTLINE SPECIFICATION CHART Weight: 12 lbs 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com 9/32″ 4.375 5.50 DIA Model # 091-11DV-6 091-11DV-12 091-11DV-24 091-1 IDV-POS 4.375 DRAWING Amps 12 12 6 12 1 1.375 10.375 OUTLINE KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS counr Voltage 6 12 24 12 Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 4

****** Page 5 ****** INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POLICY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kuss- maul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. Members of fire and Sinergency Manufacturers and Service Association Members of National Fire Protection Members of Fire Apparatus Manufacturers Made in, USA 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com Association Association NFPA KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS COUNT 5 Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.