Free English KENMORE 796.9118 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD KENMORE 796.9118 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I operate the KENMORE 796.9118?
To operate the KENMORE 796.9118, follow these steps:
1. Clean the lint filter. If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load.
2. Load the dryer with the wet laundry from the washer. If the load is extra large, you may need to divide it into smaller loads.
3. Press the POWER button to turn ON the dryer.
4. Turn the cycle selector knob in either direction until the LED for the desired cycle is illuminated.
5. Select cycle modifiers. Default settings can be changed if desired.
6. Select cycle options using the option buttons.
7. Press the START/PAUSE button to begin the cycle.
8. When the cycle is finished, remove the clothing immediately to reduce wrinkling.
What should I do if I smell gas while using the KENMORE 796.9118?
If you smell gas, follow these emergency steps:
1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2. Do not touch any electrical switches. Do not use any phones in your building.
3. Clear the room, building, or area of all occupants.
4. Immediately call your gas supplier from a neighbor’s phone. Carefully follow the gas supplier’s instructions.
5. If you cannot reach your gas supplier, call the fire department.
How do I clean the lint filter on the KENMORE 796.9118?
Always clean the lint filter before or after each load. To remove lint, open the dryer door, pull the lint filter straight up, roll any lint off the filter with your fingers, and insert the filter back into the dryer firmly. Periodically, if the filter looks dark or dirty, use hot soapy water and a stiff brush to clean it, then ensure it is completely dry before reinstallation.
What is the CHECK VENT indicator on the KENMORE 796.9118?
The CHECK VENT duct blockage sensing system detects and alerts you to blockages in the exhaust system that reduce airflow from the KENMORE 796.9118. If this light illuminates or blinks, it indicates a serious restriction in your home’s exhaust system, which should be checked and cleaned immediately.
How do I set the My Cycle feature on the KENMORE 796.9118?
To save a custom cycle on the KENMORE 796.9118: 1. Press the POWER button. 2. Turn the cycle selector knob to select the desired cycle. 3. Press the cycle modifier buttons to change desired settings. 4. Press the cycle option buttons to add desired options. 5. Press and hold the MY CYCLE button.
To recall the saved cycle, press the POWER button and then press the MY CYCLE button.
What are the AUTO DRY cycle specifications for the KENMORE 796.9118?
The following table outlines the AUTO DRY cycles for the KENMORE 796.9118:
| Cycle | Fabric Type | Temperature | Dry Level |
|---|---|---|---|
| Sanitize | Comforter, bedding, children’s clothing, etc. | High | Extra dry |
| Heavy Duty | Jeans, heavyweight items | High | Normal |
| Casual | Permanent press, synthetic items | Mid low | Normal |
| Bulky/Bedding | Comforter, pillows, shirts | Medium | Normal |
| Normal | Work clothes, etc. | Medium | Normal |
| Small Load | Only normal & cotton/towel fabric type (Max 3 lb) | High | Normal |
| Delicates | Lingerie, sheets, blouses | Mid low | Normal |
What are the TIMED DRY cycle specifications for the KENMORE 796.9118?
The following table outlines the TIMED DRY cycles for the KENMORE 796.9118:
| Cycle | Fabric Type | Temperature | Dry Level |
|---|---|---|---|
| Express Dry | For small loads with short drying times | High | Auto |
| Touch Up | For removing light wrinkles | Mid high | Auto |
| Timed Dry | For general drying | High | Auto |
How can I troubleshoot the KENMORE 796.9118 if it won’t turn on?
If the KENMORE 796.9118 will not turn on, ensure the power cord is properly plugged into a grounded outlet. Check if the house fuse is blown or the circuit breaker has tripped, and reset if necessary.
What should I do if the KENMORE 796.9118 takes too long to dry?
If the KENMORE 796.9118 takes too long to dry, check the following:
1. Confirm that exhaust ducts are not blocked, dirty, or too long.
2. Ensure the load is properly sorted, as heavy items take longer to dry.
3. Verify that the dryer controls are set correctly.
4. Clean the lint filter before every load.
5. Check that the dryer is not overloaded or underloaded.
How do I resolve greasy or dirty spots on clothes dried in the KENMORE 796.9118?
Do not dry clean and dirty items together, as soil can transfer. Ensure all clothes were properly cleaned or rinsed before being placed in the KENMORE 796.9118. Some stains may require pre-treating before washing.
What does a tE1 or tE2 error code mean on the KENMORE 796.9118?
A tE1 or tE2 error code on the KENMORE 796.9118 indicates a temperature sensor failure. Turn off the dryer and call for service.
CLICK HERE TO DOWNLOAD KENMORE 796.9118 (01) PDF DOCUMENT