Free English KENMORE 796.8128 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD KENMORE 796.8128 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I operate the KENMORE 796.8128?
To operate the KENMORE 796.8128, follow these steps:
1. Clean the lint filter. If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load.
2. Load the dryer with the wet laundry from the washer. If the load is extra large, you may need to divide it into smaller loads for proper performance and fabric care.
3. Press the POWER button to turn ON the dryer. The cycle LEDs will illuminate and a chime will sound.
4. Turn the cycle selector knob in either direction until the LED for the desired cycle is illuminated. The preset temperature, dry level, and option settings for that cycle will display.
5. Default settings for the selected cycle can now be changed, if desired.
6. Cycle options can be added using the option buttons.
7. Press the START/PAUSE button to begin the cycle.
8. When the cycle is finished, a chime will sound. Immediately remove your clothing from the dryer to reduce wrinkling.
What should I do if my KENMORE 796.8128 will not turn on?
If your KENMORE 796.8128 will not turn on, check the following:
Make sure that the plug is securely plugged into a grounded outlet matching the dryer’s rating plate.
Reset the circuit breaker or replace the fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.
What should I do if the KENMORE 796.8128 is not heating?
If your KENMORE 796.8128 is not heating, check the following:
Reset the circuit breaker or replace the fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.
Note that due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat.
If you have a gas model, confirm that the house gas shutoff and the dryer gas shutoff valves are both fully open. Even if gas is not supplied to the dryer, it will run and no error codes will display. Verify that other gas appliances in the home are working normally.
What does it mean if the CHECK VENT indicator on my KENMORE 796.8128 is blinking?
If the CHECK VENT indicator on your KENMORE 796.8128 is blinking, it means the external venting should be checked for potential restrictions as soon as possible.
The CHECK VENT duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. A blinking light indicates your home’s exhaust system has a serious restriction, which will lead to longer dry times and higher energy consumption.
To resolve this, install a shorter or straighter duct run. Ductwork should be checked and cleaned immediately. The dryer can be used in this condition, but drying times will be longer and energy consumption will increase. It will take several cycles after cleaning or repairing the exhaust for the indicator to reset and turn off.
How can I clean the lint filter on the KENMORE 796.8128?
To remove lint from the KENMORE 796.8128 between cycles:
1. Open the dryer door.
2. Pull the lint filter straight up.
3. Roll any lint off the filter with your fingers.
4. Insert the lint filter back into the dryer.
For periodic thorough cleaning if the filter looks dark or dirty when held up to the light:
1. Use hot soapy water and a stiff brush to clean the filter.
2. Make sure the filter is completely dry before reinstalling it and using the dryer.
What are the AUTO DRY cycles available on the KENMORE 796.8128?
The AUTO DRY cycles for the KENMORE 796.8128 are as follows:
| Cycle | Fabric Type | Temperature | Dry Level |
|---|---|---|---|
| Sanitize | Comforter, bedding, children’s clothing, etc. | High | Extra dry |
| Heavy Duty | Jeans, heavyweight items | High | Normal / Adjustable |
| Casual | Permanent press, synthetic items | Mid low | Normal / Adjustable |
| Bulky/Bedding | Comforter, pillows, shirts | Medium | Normal / Adjustable |
| Normal | Work clothes, etc. | Medium | Normal / Adjustable |
| Small Load | Only normal & cotton/towel fabric type (Max 3 lb) | High | Normal / Adjustable |
| Delicates | Lingerie, sheets, blouses | Mid low | Normal / Adjustable |
What are the TIMED DRY cycles available on the KENMORE 796.8128?
The TIMED DRY cycles for the KENMORE 796.8128 are as follows:
| Cycle | Fabric Type | Temperature | Dry Level |
|---|---|---|---|
| Express Dry | For small loads with short drying times | High / Adjustable | Auto |
| Touch Up | For removing light wrinkles | Mid high / Adjustable | Auto |
| Timed Dry | For general drying, can be set manually | High / Adjustable | Auto |
How do I use the WRINKLE GUARD feature on the KENMORE 796.8128?
Selecting the WRINKLE GUARD option on the KENMORE 796.8128 will tumble the clothes after the cycle ends for a few seconds every few minutes without heat. This option is active for 150 minutes after the end of the cycle, or until the door is opened. This helps prevent wrinkles if the clothes are not removed immediately after the cycle has finished.
How do I set and recall a MY CYCLE on the KENMORE 796.8128?
To save a MY CYCLE on the KENMORE 796.8128:
1. Press the POWER button to turn on the dryer.
2. Turn the cycle selector knob to select the desired cycle.
3. Press the CYCLE MODIFIER button to change the desired setting.
4. Press the CYCLE OPTION button to add the desired options.
5. Press and hold the MY CYCLE button.
To recall a MY CYCLE on the KENMORE 796.8128:
1. Press the POWER button to turn on the dryer.
2. Press the MY CYCLE button. The stored settings will be displayed.
3. Press the START/PAUSE button to start the cycle.
How do I lock the controls on the KENMORE 796.8128?
To lock the controls on the KENMORE 796.8128, press and hold the TOUCH UP button for five seconds. The Control Lock can be activated any time the dryer is ON. When the controls are locked, CL will display alternately with the estimated time remaining. Once set, the Control Lock must be turned off before the controls can be used.
CLICK HERE TO DOWNLOAD KENMORE 796.8128 (01) PDF DOCUMENT