FREE ENGLISH JVC CS-MX614 (01) PDF USER GUIDE
FREE ENGLISH JVC CS-MX614 (01) PDF USER MANUAL
FREE ENGLISH JVC CS-MX614 (01) PDF OWNER GUIDE
FREE ENGLISH JVC CS-MX614 (01) PDF OWNER MANUAL
FREE ENGLISH JVC CS-MX614 (01) PDF REFERENCE GUIDE
FREE ENGLISH JVC CS-MX614 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH JVC CS-MX614 (01) PDF REFERENCE MANUAL
FREE ENGLISH JVC CS-MX614 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH JVC CS-MX614 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD JVC CS-MX614 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
JVC CS-MX614 (01) PDF SUMMARY:
What should I do for proper installation and use?
- Be sure to install where the speakers will not interfere with the boat’s safety.
- Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers.
- The amplifier and speakers should be connected between corresponding terminals, i.e. left to left, and right to right, as well as “+” to “+”, and “-” to “-”. Connection with reversed polarity will degrade the quality of stereo reproduction.
- Do not subject the speakers to excessive input. The power handling capacity of the CS-MX614 is 120 watts (MAX. MUSIC POWER) and CS-MX624 is 150 watts (MAX. MUSIC POWER). Any excessive input may damage the speakers
- The CS-MX614/CS-MX624 has an impedance of 4 ohms. Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.
- When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.
What is the impedance of the speakers?
4 ohms.
What is the magnet mass of the CS-MX614?
182 g (6.4 oz).
What is the magnet mass of the CS-MX624?
228 g (8 oz).
What is the mass of the CS-MX614?
0.7 kg (1.6 lbs).
What is the mass of the CS-MX624?
0.85 kg (1.9 lbs).
Where should you install the speakers?
Install the speakers where they will not interfere with the boat’s safety.
When connecting the speakers to the amplifier, what should you confirm before connecting them?
Confirm that the power has been turned off.
Why should you make sure that the power to the amplifier has been turned off before connecting the speakers?
The click noise generated by the connection if the power is on may damage the speakers.
How should the amplifier and speakers be connected?
The amplifier and speakers should be connected between corresponding terminals, i.e. left to left, and right to right, as well as “+” to “+”, and “-” to “-”.
What will degrade the quality of stereo reproduction?
Connection with reversed polarity will degrade the quality of stereo reproduction.
What is the power handling capacity of the CS-MX614?
120 watts (MAX. MUSIC POWER).
What is the power handling capacity of the CS-MX624?
150 watts (MAX. MUSIC POWER).
What could happen if the speakers are subjected to excessive input?
Any excessive input may damage the speakers.
What is the output impedance of the amplifier’s speaker terminal?
4 ohms.
What should you use to clean the speakers?
When cleaning the speakers, use a soft cloth and wipe the surface gently.
What should you not apply when cleaning the speakers?
Do not apply thinner or solvent.
Where should you install the speakers?
Install the speakers so they do not interfere with the safety of the boat.
What should you do before connecting the speakers to the amplifier?
Make sure that the amplifier is turned off when connecting the speakers to it!
Why should you make sure that the amplifier is turned off when connecting the speakers to it?
The sound that occurs when connecting them could damage the speakers if the amplifier is turned on.
How should you connect the cables?
The marking of the cable connectors and plugs for the amplifier and speakers should match, i.e. “Left” to “Left” and “Right” to “Right” or “+” to “+” and “-” to “-”.
What will reduce the quality of stereo playback?
A reversed (crossed) connection reduces the quality of stereo playback.
What should you not connect the speakers to?
Do not connect the speakers to an amplifier with too high an output power!
What is the maximum power the CS-MX614 speakers are designed for?
120 watts (MAX. MUSIC OUTPUT).
What is the maximum power the CS-MX624 speakers are designed for?
150 watts (MAX. MUSIC OUTPUT).
What could damage the speakers?
Too high an amplifier output power can damage the speakers.
What is the impedance of the CS-MX614/CS-MX624?
4 Ohm.
What must the output impedance of the amplifier also be?
4 ohms.
What should you use to clean the speakers?
Use a soft cloth to clean the speakers.
How should you clean the speakers?
Wipe gently over the surface when cleaning the speakers.
What should you not use to clean the speakers?
Do not use any cleaning agent (thinner or solvent)!
Where should you install the speakers?
Install the speakers where they do not pose a safety hazard.
What should you check before connecting the speakers to the amplifier?
Check that the power is off before connecting the speakers to the amplifier.
Why should you check that the power is off before connecting the speakers to the amplifier?
The crackling noises produced by the connection when the power is on may damage the speakers.
How should you connect the terminals of the amplifier and speakers?
Connect the corresponding terminals of the amplifier and the speakers, i.e. left to left, right to right, as well as “+” to “+” and “-” to “-”.
What will reduce the quality of the stereophonic sound reproduction?
A connection made by reversing the polarities will reduce the quality of the stereophonic sound reproduction.
What should you not apply to the speakers?
Do not apply an excessive input level to the speakers.
What is the permissible input power for the CS-MX614 speakers?
120 watts (maximum music power).
What is the permissible input power for the CS-MX624 speakers?
150 watts (maximum music power).
What may damage the speakers?
Any excessive input signal may damage the speakers.
What is the impedance of the CS-MX614/CS-MX624 speakers?
4 ohms.
What must you make sure of?
Make sure that the output impedance at the amplifier’s loudspeaker terminals is also 4 ohms.
How should you clean the speaker?
Clean the speaker by rubbing it lightly with a soft cloth.
What should you never use to clean the speakers?
Never use solvents or detergents.
Where should you install the speakers?
Install the speakers so that they cannot endanger safety on board in any way.
What should you do before connecting the speakers to the amplifier?
Before connecting the speakers to the amplifier, you should make sure that the latter is switched off.
What could happen if you connect the speakers while the amplifier is on?
The noise caused by making connections can result in damage to the speaker.
How should the amplifier and speakers be connected?
The amplifier and speakers must be connected correctly.
To what should you connect left, right, “+”, and “-”?
Connect left to left, right to right and “+” to “+”. “-” to “-”.
What will deteriorate the quality of the stereo sound?
A reversed connection will deteriorate the quality of the stereo sound.
What should you not expose the speakers to?
Do not expose the speakers to too much power.
What is the power consumption of the CS-MX614 speakers?
120 watts (max. music power).
What is the power consumption of the CS-MX624 speakers?
150 watts (max. music power).
What will damage the speakers?
A higher input power will damage the speakers.
What is the impedance of the CS-MX614/CS-MX624?
4 Ohm.
What should you check?
Check that the output impedance of the speaker connections of the amplifier is 4 Ohm.
What should you use to clean the speakers?
Use a soft cloth to clean the speakers.
What should you not use to clean the speakers?
Do not use thinner or other solvents.
Where should you install the speakers?
Make sure to install the speakers where they will not interfere with the safety of your boat.
What should you confirm before connecting the speakers to the amplifier?
Before connecting the speakers with the amplifier, confirm that the electrical power is cut off.
Why should you confirm that the electrical power is cut off before connecting the speakers to the amplifier?
The noise produced when plugging in the connection terminals while energy is being supplied can cause damage to the speakers.
How should the speakers and amplifier be connected?
The speakers and the amplifier must be connected to the corresponding terminals.
Give an example of how to connect the speakers and the amplifier.
For example: Left to left, and right to right, as well as “+” to “+” and “-” to “-”.
What will degrade the quality of the stereophonic reproduction?
Connection with inverted polarity will degrade the quality of the stereophonic reproduction.
What should you not subject the speakers to?
Do not subject the speakers to an excessive input.
What is the maximum capacity of the CS-MX614 speakers?
120 watts (MAXIMUM MUSIC MODULATION POWER).
What is the maximum capacity of the CS-MX624 speakers?
150 watts (MAXIMUM MUSIC MODULATION POWER).
What will damage the speakers?
An excessive input will damage the speakers.
What is the impedance of the CS-MX614/CS-MX624 speakers?
4 ohms.
What should you make sure of?
Make sure that the output impedance of the amplifier’s speaker terminal is 4 ohms.
What should you use to clean the speakers?
Use a soft cloth to clean the speakers.
How should you clean the speakers?
Clean the surface gently when cleaning the speakers.
What should you not use to clean the speakers?
Do not use thinner or solvents.
Where should you mount the speakers?
Mount the speakers so that they do not reduce safety when driving the boat.
What should you check before connecting the speakers?
Check that the power to the amplifier has been disconnected before connecting the speakers.
Why should you check that the power to the amplifier has been disconnected before connecting the speakers?
The clicking sound that occurs when the speakers are connected with the power switched on can damage them.
How should the connections between the amplifier and the speakers be made?
The connections between the amplifier and the speakers must be made to the correct speaker terminals.
How should the connections between the amplifier and the speakers be made?
Left to left and right to right, as well as “+” to “+” and “-” to “-”.
What will impair the reproduction of stereo sound?
Connecting with reversed polarity will impair the reproduction of stereo sound.
What should you not expose the speakers to?
Do not expose the speakers to excessive input effects.
What is the rated power for CS-MX614?
120 watts (max. music power).
What is the rated power for CS-MX624?
150 watts (max. music power).
What can damage the speakers?
Too high an input signal can damage the speakers.
What is the impedance of the CS-MX614/CS-MX624?
4 ohms.
What should you check?
Check that the output impedance for the amplifier’s speaker terminals is also 4 ohms.
What should you use to clean the speaker cabinets?
Clean the speaker cabinets with a soft cloth.
How should you clean the speakers?
Wipe the surface carefully.
What should you not use to clean the speakers?
Do not use thinner or any other solvent for cleaning.
What should you do before installing speakers?
Before installing speakers, etc., you must first determine the appropriate area in which to place it.
What does the paper pattern on the bottom of the packing box show?
The paper pattern printed on the bottom of the packing box shows the exact shape of the area through which the speaker will be installed.
Where should you apply the paper pattern?
Apply the paper pattern onto the area determined in 1. above.
What should you trace out?
Trace out the shape of the area on a bulkhead, etc.
What should you do after tracing out the shape of the area on a bulkhead?
Cut out the marked area.
What is the next step after cutting out the marked area?
The next step is to wire the speakers.
What should you consult carefully?
Consult the diagram carefully.
What should you use to fix the speaker to a bulkhead?
Use the tapping screws and speed nuts provided to fix the speaker to a bulkhead, etc.
What should you do after fixing the speaker to a bulkhead?
Insert the screw caps provided.
How should you install the speakers?
Install the speakers with the terminals down.
What should you do when removing the speaker?
Remove the screw caps first.
What model speaker is illustrated?
The speaker illustrated here is the CS-MX614.
Where should you place the paper template when installing the speakers?
Place the template on the position determined in 1. on the partition wall, etc., and trace the surface outlines.
What should you do after you have traced the surface outlines?
Then cut out the marked areas.
What should be done next?
The next step is the wiring.
What should you pay attention to when wiring the speakers?
Carefully observe the information in the wiring diagram!
What should you use to attach the speakers to the partition wall, etc.?
Use the enclosed self-tapping screws and nuts to attach the speakers to the partition wall, etc.
What should you attach after attaching the speakers to the partition wall?
Attach the supplied screw caps.
How should you install the speakers?
Install the speakers with the terminals pointing downwards.
What should you do when removing the speakers?
First remove the screw caps as shown.
What does the diagram below show?
The diagram below shows the cable connection.
What should you connect together?
Connect terminals of the same type: “Left” to “Left”, “-” to “-”, etc.
Where should you place the paper template when installing the speakers?
Place the paper template at the location mentioned in 1. above in order to mark the shape on the bulkhead, etc.
What should you do after placing the paper template?
Cut out the marked area.
What is the next step?
Next, attach the speaker wiring.
What should you follow carefully?
Follow the diagram carefully.
What should you use to fix the speakers on the bulkhead?
Use the countersunk screws and speed nuts provided to fix the speakers on the bulkhead, etc.
What should you do after fixing the speakers to the bulkhead?
Insert the screw caps provided.
How should you install the speakers?
Install the speakers with the terminals facing down.
What should you do when removing the speaker?
When removing the speaker, first remove the screw caps.
What does the diagram below show?
The diagram below shows how to complete the wiring.
What should you take care of when connecting the terminals?
Take care to connect the corresponding terminals, i.e. left to left, “-” to “-”, etc.
What should you do to install the speakers?
To install the speakers, etc., you must first determine the correct installation position.
What does the pattern printed on the underside of the box show?
The pattern that is printed on the underside of the box shows exactly the shape of the area through which the speaker will be mounted.
Where should you place the pattern?
Place the pattern on the surface determined in 1.
What should you do after you have placed the pattern on the surface?
Then draw it on the surface.
What should you do after you have drawn the pattern on the surface?
Cut or saw the marked section out of the shelf.
What is the next step?
The next step is connecting the wiring to the speaker.
What should you follow carefully when connecting the wiring to the speaker?
Follow the diagram carefully when connecting the wiring to the speaker.
What should you use to attach the speaker?
Use the supplied tapping screws and clip nuts to attach the speaker.
What should you place after you have attached the speaker?
Place the supplied screw caps.
How should you mount the speakers?
Mount the speakers with the terminals at the bottom.
What should you remove first when removing the speaker?
When removing the speaker, first remove the screw caps.
What should you consult?
Consult the diagram below when connecting the wiring.
What should you pay attention to when connecting the wiring?
Pay attention to the different inputs and outputs, do not swap them, and make sure that you connect the left speaker to the left channel, the " " wire to the “-” terminal, and so on.
What should you determine first when installing the speaker?
First, determine the appropriate area where you will place it.
What does the paper diagram printed at the bottom of the packing box show?
The paper diagram printed at the bottom of the packing box shows the exact shape of the area where the speaker will be installed.
Where should you apply the diagram?
Apply said diagram in the area determined in the previous point 1.
What should you do after applying the diagram in the area?
And follow the shape of the area on the bulkhead, etc.
What should you cut after following the shape of the area on the bulkhead?
Cut the marked area.
What is the next step?
The next step is to connect the speaker.
What should you consult carefully?
Consult the diagram carefully.
What should you use to secure the speaker to the bulkhead?
Use the provided male thread screws and quick-tightening nuts to secure the speaker to the bulkhead, etc.
What should you place after securing the speaker to the bulkhead?
Place the supplied screw caps.
How should you install the speakers?
Install the speakers with the terminals facing down.
What should you do to remove the speaker?
To remove the speaker, first remove the screw caps.
What should you consult?
Consult the following diagram to complete the electrical connections.
What should you make sure of when connecting the terminals?
Make sure to connect the corresponding terminals, that is, left to left, “-” to “-”, etc.
What does the template on the bottom of the box correspond to?
The template on the bottom of the box corresponds exactly to the speaker’s contour.
Where should you lay the template?
Lay it over the spot selected in step 1 above.
Where should you draw the template?
Draw it on the bulkhead, etc.
What should you do after you have drawn the template?
Then cut out the marked area.
What is the next procedure?
The next procedure is to connect the speakers.
What should you follow carefully?
Follow the diagram carefully.
What should you use to screw on the speakers?
Screw on the speakers with the supplied screws and nuts.
What should you put on after screwing on the speakers?
Put on the included screw caps.
How should you install the speakers?
Install the speakers with the terminals facing down.
What should you remove first when removing the speakers?
When removing the speakers, first remove the screw caps.
What does the diagram below show?
The diagram below shows the connection.
What should you make sure to do when connecting the speakers?
Make sure to connect to the correct speaker terminal, i.e. left to left, “-” to “-”, etc.
Where should you consult to find a car audio specialty shop?
Consult your telephone directory.
CLICK HERE TO DOWNLOAD JVC CS-MX614 (01) PDF MANUAL