INGERSOLL RAND 3129XPA (01) PDF DOCUMENT

The INGERSOLL RAND 3129XPA Polishers are designed for buffing and polishing.

Model	Free Speed	Pad Diameter		Sound Level dB(A) (ISO 15744)		Vibration m/s² (ISO 28927)
	rpm	inch	mm	Pressure (Lp)	Power (Lw)	Level	K
3129XPA	6,400	3″	76.2	81.5	92.5	2.7	0.7

† KpA = 3dB measurement uncertainty

‡ KwA = 3dB measurement uncertainty

* K = Vibration measurement uncertainty

The sound and vibration values for the INGERSOLL RAND 3129XPA were measured in compliance with internationally recognized test standards. The exposure to the user in a specific tool application may vary from these results. Therefore, on-site measurements should be used to determine the hazard level in that specific application.

Size the air supply line to ensure the tool’s maximum operating pressure (PMAX) at the tool inlet. Drain condensate from the valve(s) at the low point(s) of piping, air filter, and compressor tank daily. Install a properly sized Safety Air Fuse upstream of the hose and use an anti-whip device across any hose coupling without an internal shut-off to prevent hose whipping if a hose fails or a coupling disconnects.

The recommended components for the air supply setup are as follows:

1. Air filter

2. Regulator

3. Lubricator

4. Emergency shut-off valve

5. Hose diameter

6. Thread size

7. Coupling

8. Safety Air Fuse

9. Oil

10. Grease (during assembly)

Maintenance frequency is shown in a circular arrow where h=hours, d=days, and m=months of actual use.

Filter/Regulator/Lubricator IR # – NPT	Filter/Regulator/Lubricator IR # – BS	Hose Diameter inch (mm)	Thread Size NPT	Oil IR #	Grease IR #	Grease cm³
C38341-810	C383D1-810	3/8″ (10)	1/4	10	67	3

Always turn off the air supply, bleed the air pressure, and disconnect the air supply hose when not in use, before installing, removing, or adjusting any accessory on this tool, or before performing any maintenance on this tool or any accessory.

Backing Pads should be inspected for signs of irregularities such as fractures, excessive wear, nicks, or cuts at the edges of the center hole. Pads showing such characteristics should not be used.

The parts involved are:

A: Polishing Pad

B: Backing Pad

C: Wrench Tool

To install the hook and loop pad:

1. Use the wrench (C) to hold the spindle in place.

2. Thread the backing pad (B) onto the spindle.

3. Center the polishing pad (A) and attach it onto the backing pad (B).

When the life of the INGERSOLL RAND 3129XPA has expired, it is recommended that the tool be disassembled, degreased, and the parts be separated by material so that they can be recycled.

Tool repair and maintenance for the INGERSOLL RAND 3129XPA should only be carried out by an authorized Service Center.

The Year of Manufacture is indicated by a code on the tool. The code format includes the year and a letter for the month. For example, in the code T20A0001, ’20’ represents the year (2020) and ‘A’ represents the month (January).

The letter codes for the months are:

A = January

B = February

C = March

D = April

E = May

F = June

G = July

H = August

J = September

K = October

L = November

M = December

Object of Declaration: Mini Polisher (model) 3129XPA

Serial Number Range: 222E010001 –> 230M319999

Directive(s) Conformity: 2006/42/EC (Machinery)

Standard(s) Compliance: EN ISO 15744:2008, EN ISO 28927-3:2009 and EN ISO 11148-8:2011

Object of Declaration: Mini Polisher (model) Model 3129XPA

Serial Number Range: 222E010001 –> 230M319999

Directive(s) Conformity: Supply of Machinery (Safety) Regulations 2008

Standard(s) Compliance: BS EN ISO 15744:2008, BS EN ISO 28927-3:2009 and BS EN ISO 11148-8:2011