IIYAMA PROLITE E1980S (01) PDF MANUAL

If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock.

High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock. Therefore, never remove the cabinet.

Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fire, electric shock or damage.

Install the monitor on a flat, stable surface. The monitor may cause an injury if it falls or is dropped.

Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock.

Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will cause malfunction and may cause fire or electric shock.

Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause fire or electric shock.

It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock.

Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor.

The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may not pull the cables and possibly cause injury.

Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls. When removing the tilt stand, the ventilation slots on the back side of the monitor can be blocked. This may overheat the monitor and may cause fire or damage. Make sure to allow enough ventilation when removing the tilt stand. Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also cause damage.

When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.

If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.

To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause fire or electric shock.

Pulling or inserting the plug with wet hands may cause electric shock.

Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer.

Be careful not to hurt your fingers or hands when you change the height or the angle.

Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height. (Just for height adjustable model.)

Do not spray alcohol or disinfectants directly onto the monitor or use them near the monitor. Also, do not wipe the monitor with a cloth or sheet that contains alcohol or disinfectants. These may cause discoloration, deterioration, or cracking of the cabinet, damage to the surface treatment of the LCD panel, and deterioration of components.

If you absolutely must disinfect the monitor with alcohol, please understand the warnings and cautions in advance. Also, avoid frequent alcohol disinfection.

When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position.

You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen can be recovered slowly by changing the image or turning off the Power Switch for some hours.

Do not spray alcohol or disinfectants directly onto the monitor or use them near the monitor. Also, do not wipe the monitor with a cloth or sheet that contains alcohol or disinfectants. These may cause discoloration, deterioration, or cracking of the cabinet, damage to the surface treatment of the LCD panel, and deterioration of components.

To avoid potential damage on the monitor (LCD panel/cabinet/connector terminals) or accessories, never use the following strong solvents or cleaning sheets. These may cause discoloration, deterioration, or cracking of the cabinet, damage to the surface treatment of the LCD panel, and deterioration of components:

Benzine, Thinner, Alcohol, Bleach, Peroxide, Acetone, Methylene chloride, Toluene, Ammonia, Sodium hypochlorite solution (Chlorine bleach), Hypochlorous acid water, Acidic or alkaline solvents, Wax, Abrasives, Office equipment cleaner, Glass cleaner, Tissue paper, Wet tissue, Chemical cloth, Cleaning paper.

Gently wipe the cabinet with a soft, dry and clean cloth. If your monitor is particularly dirty, soak the cloth in a mild detergent thoroughly diluted with water, wring it out tightly, and then wipe the dirt off. Then immediately wipe it with a soft, dry cloth.

The ProLite B1980S and ProLite E1980S LCD Monitors feature:

Supports Resolutions up to 1280 × 1024

High Contrast 1000:1 (Typical), Adv. Contrast Function Available / Brightness 250cd/m² (Typical) / Quick Response Time 3ms (Gray to Gray)

Digital Character Smoothing

2 × 2W Stereo Speakers

Standby Feature

VESA Mounting Standard (100mm×100mm) Compliant

Keyhole for Security Lock

The following accessories are included in your package:

Power Cable

HDMI Cable

Stand-Base with a screw (Accessory for ProLite B1980S)

Stand-Base (Accessory for ProLite E1980S)

Stand-Neck

Cable Holder (Accessory for ProLite E1980S)

Screwdriver (Accessory for ProLite B1980S)

Safety Guide

Quick Start Guide

Before installation, make sure the wall, ceiling or desktop arm is strong enough to hold the necessary weight of the display and the mount.

Regularly check the tightness of the screws. If the screws are not tight enough, the monitor may come off and cause injury or damage.

When you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screws (4 pcs) which “L” length is 7mm to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.

2. Install the Stand-Neck to the monitor and then tighten the ‘thumb screw’ with the provided screwdriver to secure them.

3. Install the Stand-Base to the Stand-Neck and then tighten the ‘thumb screw’ to secure them.

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.

2. Loosen the ‘thumb screw’ to remove the Stand-Base from the monitor.

3. Loosen the ‘thumb screw’ with the provided screwdriver to remove the Stand-Neck from the monitor.

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.

2. Hold the monitor and install the Stand-Neck to the monitor until it clicks to secure.

3. Install the Stand-Base to the Stand-Neck.

4. Place the Cable Holder.

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.

2. Keep pressing the Hooks inward to pull out the Stand-Base.

3. There are two locks inside of the Stand-Neck, unlock them by thin stick and pull the Stand-Neck away from the monitor.

The ProLite B1980S has the following controls and connectors:

1. Power Switch (Power icon)

2. Menu Button (MENU)

3. + / Volume Button (+ / up arrow / speaker icon)

4. Power Indicator (Blue: Normal operation, Orange: Standby Mode)

5. – / Eco Button (- / down arrow / leaf icon)

6. Signal Select Button (AUTO)

7. Speakers

8. HDMI Connector (HDMI)

9. DisplayPort Connector (DP)

10. Cable Hole

11. AC Connector (~ : Alternating current)

12. Keyhole for Security Lock

The ProLite E1980S has the following controls and connectors:

1. Power Switch (Power icon)

2. Menu Button (MENU)

3. + / Volume Button (+ / up arrow / speaker icon)

4. Power Indicator (Blue: Normal operation, Orange: Standby Mode)

5. – / Eco Button (- / down arrow / leaf icon)

6. Signal Select Button (AUTO)

7. Speakers

8. HDMI Connector (HDMI)

9. DisplayPort Connector (DP)

10. Installation hole of Cable Holder

11. AC Connector (~ : Alternating current)

12. Keyhole for Security Lock

1. Ensure that both the computer and the monitor are switched off.

2. Connect the computer to the monitor with the signal cable.

3. Connect the Power Cable to the monitor first and then to the power source.

4. Turn on your monitor and computer.

The Class I pluggable equipment Type A must be connected to protective earth. The socket-outlet shall be installed near the equipment and shall be easily accessible.

Put the cables through the Cable Hole to bundle them.

1. Ensure that both the computer and the monitor are switched off.

2. Connect the computer to the monitor with the signal cable.

3. Connect the Power Cable to the monitor first and then to the power source.

4. Turn on your monitor and computer.

The Class I pluggable equipment Type A must be connected to protective earth. The socket-outlet shall be installed near the equipment and shall be easily accessible.

For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor, then adjust the monitor’s height and angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor’s height or angle. You are able to adjust the monitor’s height up to 150mm, angle up to 60° right and left, 23° upward and 5° downward.

Do not touch the LCD screen when you change the height or the angle. It may cause damage or break the LCD screen. Careful attention is required not to pinch your fingers or hands into the moving part of the stand when you change the height or the angle. Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height.

For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor’s angle. You are able to adjust the monitor’s angle up to 21° upward, 4° downward. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10°. Adjust the monitor’s angle to your own preference.

Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to pinch your fingers or hands into the moving part of the stand when you change the angle.

1. Press the MENU Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the + / – Buttons.

2. Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. Press the MENU Button. Then, use the + / – Buttons to highlight the desired adjustment icon.

3. Press the MENU Button again. Use the + / – Buttons to make the appropriate adjustment or setting.

4. Press the AUTO Button to leave the menu, and the settings you just made would be automatically saved.

Any changes are automatically saved in the memory when the On Screen Display disappears. Turning off the power should be avoided while using the Menu.

If the picture is too dull, increase Contrast by pressing the + button. If the picture is too intense, decrease Contrast by pressing the – button.

If the picture is too dark, increase Brightness by pressing the + button. If the picture is too bright, decrease Brightness by pressing the – button.

You can select from the following options:

Off: Return to a state set by color adjustment except i-Style Color.

Standard: For general windows environment and monitor default setting.

Text: For text editing and viewing in a word processing environment.

Internet: For internet environment.

Game: For PC game environment.

Movie: For movie and video environment.

Sports: For sport environment.

You can select On for Increased Contrast Ratio or Off for Typical Contrast Ratio.

Adv. Contrast adjusts brightness according to the image, and improves the contrast ratio during movie playing. Contrast, Brightness, i-Style Color, Eco, Gamma and Color Temp. cannot be adjusted and selected while Adv. Contrast is active.

You can select from the following options:

Off: Normal.

Mode1: Brightness of back-light is reduced.

Mode2: Brightness of back-light is reduced more than Mode1.

Mode3: Brightness of back-light is reduced more than Mode2.

To access Eco mode directly, press the – Button when the Menu is not displayed.

You can select Off/1/2/3/4/5. It will improve the gray level response time of the LCD panel. A higher level results in a faster response time.

You can select from the following options:

Off: Normal.

Soft: Enhance the picture edge.

Middle: Enhance the picture edge more than the Soft option.

Hard: Enhance the picture edge more than the Middle option.

You can select from the following options:

Off: Typical.

Mode 1: Blue light is reduced.

Mode 2: Blue light is reduced more than Mode 1.

Mode 3: Blue light is reduced more than Mode 2.

To access Blue Light Reducer directly, press and hold the – Button for about 3 seconds when the Menu is not displayed.

You can change the picture quality from 1 to 6 (sharp to soft). Press the + Button to change the picture quality in numerical order. Press the – Button to change the picture quality in reverse numerical order.

You can select from Gamma1 (Normal), Gamma2 (Dark), or Gamma3 (High contrast).

You can adjust Hue for Red, Yellow, Green, Cyan, Blue, and Magenta. Use the + button for “Too strong” and the – button for “Too weak” adjustment.

You can adjust Saturation for Red, Yellow, Green, Cyan, Blue, and Magenta. Use the + button for “Too strong” and the – button for “Too weak” adjustment.

You can select from User, Warm (Warm color), Normal (Normal color), or Cool (Cool color).

If “User” is selected, you can adjust Red, Green, and Blue levels. Use the + button for “Too strong” and the – button for “Too weak” adjustment.

If the sound is too soft, increase Volume by pressing the + button. If the sound is too loud, decrease Volume by pressing the – button.

To access Volume adjustment directly, press the + Button when the Menu is not displayed.

You can select On to turn off the sound temporarily, or Off to return the sound volume to the previous level.

To access Mute function directly, press and hold the + Button for about 3 seconds when the Menu is not displayed.

If OSD is too left, press the + button. If OSD is too right, press the – button.

If OSD is too low, press the + button. If OSD is too high, press the – button.

You can set the OSD display duration time between 5 and 60 seconds. Use the + button to increase time and the – button to decrease time.

You can rotate the OSD to 0°, +90°, or -90°.

+90° is appropriate for portrait mode with the monitor rotated to the right.

-90° is appropriate for portrait mode with the monitor rotated to the left.

You can select from English, Deutsch (German), Español (Spanish), Français (French), Italiano (Italian), 日本語 (Japanese), Nederlands (Dutch), Polski (Polish), Português (Portuguese), Русский (Russian), and Česky (Czech).

Select Yes to restore factory-preset data, or No to return to Menu.

You can turn DDC/CI On or Off.

You can select from Auto (selects available source automatically), HDMI (Digital HDMI input), or DP (Digital DisplayPort input).

If “Auto” is selected, only one source available is selected automatically. If there are more input sources available and you select one of them, the “Auto” option is not available. If multiple inputs are connected, the monitor may not recover the last one used after turning it off and on again. It is only possible when you set a specific source.

To access Signal Select directly, press the AUTO Button when the Menu is not displayed.

You can select from Auto (Selects HDMI Range automatically), Full Range (For full-range color scale signal), or Limited Range (For limited color scale signal).

You can select On for Opening Logo is On, or Off for Opening Logo is Off.

You can select On for the Power Indicator is turned On, or Off for the Power Indicator is turned Off.

Turn Off the Power Indicator when you are bothered by the light.

The Function Correlation Matrix shows the availability of different picture adjustment settings based on the activated item:

✓: Available

-: Not available

This product features the standby function. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. When the video signal from the computer is off, the monitor enters into Standby Mode which reduces the power consumption to less than 0.5W. The screen becomes dark, and the power indicator turns to orange. From Standby Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.

Check that the Power Cable is firmly seated in the socket. Ensure the Power Switch is turned ON. Verify that the AC socket is live by checking with another piece of equipment.

If the blank screen saver is in active mode, touch the keyboard or the mouse. Increase the Contrast and/or Brightness. Ensure the computer is ON. Check that the Signal Cable is properly connected. Verify that the signal timing of the computer is within the specification of the monitor.

If the monitor is in standby mode, touch the keyboard or the mouse. Ensure the computer is ON. Check that the Signal Cable is properly connected. Verify that the signal timing of the computer is within the specification of the monitor.

Check that the Signal Cable is properly connected. Verify that the signal timing of the computer is within the specification of the monitor.

Verify that the signal timing of the computer is within the specification of the monitor.

Verify that the video output level of the computer is within the specification of the monitor.

Verify that the power voltage is within the specification of the monitor. Verify that the signal timing of the computer is within the specification of the monitor.

Ensure that the audio equipment (computer etc.) is ON. Check that the Volume is turned up. Verify that the Mute is OFF. Ensure that the audio output level of the audio equipment is within the specification of the monitor.

Verify that the audio output level of the audio equipment is within the specification of the monitor.

The dimensions of the ProLite B1980S monitor are:

• Width: 411.0mm (16.2″)
• Height (minimum): 453.0mm (17.8″)
• Height (maximum adjustment): 603.0mm (23.7″)
• Depth: 245.5mm (9.7″)
• Panel width: 378.5mm (14.9″)
• Panel height: 303.0mm (11.9″)
• Panel height with stand from bottom: 352.0mm (13.9″)
• Side depth (top to bottom): 49.0mm (1.9″)
• Stand base width: 267.0mm (10.5″)
• Stand base depth: 209.5mm (8.3″)

The dimensions of the ProLite E1980S monitor are:

• Width: 411.0mm (16.2″)
• Height: 402.0mm (15.8″)
• Depth: 204.5mm (8.0″)
• Panel width: 378.5mm (14.9″)
• Panel height: 303.0mm (11.9″)
• Panel height with stand from bottom: 352.5mm (13.9″)
• Side depth (top to bottom): 49.0mm (1.9″)
• Stand base width: 219.5mm (8.6″)

The compliant timing modes are: