IEKO APOLLO IK651MF (01) PDF Document

Ensure the plug is fully inserted into the wall outlet and the product is operated on an electric power source matched to its rated voltage.

Never operate the product if the cord or adaptor is damaged or overly hot.

Do not modify the cord or damage it in any way such as by bending, twisting or pulling on it unnecessarily.

Do not attempt to modify, repair or in any way dismantle the product, other than when discarding it at the end of its useful life.

Do not allow the power cord to be immersed in, splashed with, or rinsed under water.

Never unplug this product with wet hands.

Unplug the product from the wall outlet before cleaning and maintenance. Do not use liquid cleaners or aerosol cleaners.

The power cord should be unplugged from the wall outlet when unused for a long period of time.

Keep and storage this product in dry and not moisture area when are not using.

Do not use this product near water, or any other heat sources or other apparatus that produce heat.

Battery shall not be direct exposed to sunshine and fire.

Do not attempt to replace the battery. For repairing and servicing, please consult from the store of purchase or customer service centre designated by the store. CAUTION: Danger of explosion if battery is incorrectly replaced.

Do not use any other power supply other than the one specially designed for this product.

Keep this operating instruction in a safe place.

Contact an authorized service centre if you have any inquiry about this product.

Unpack the unit and ensure the power ON/OFF switch is on “OFF”.

Connect the supplied AC adaptor to the unit and plug the AC cord into the wall outlet.

Switch the Power to “ON”.

The Power RED LED will turn on.

The Battery GREEN LED indicator will turn on.

The unit is ready to use.

Once the power switch turns to “On”, Bluetooth “BT” mode has set as default.

The Blue LED indicator will be long bright after Bluetooth connection. The RED LED display will show “BT”.

Turn on the Bluetooth function on your device and search for the Bluetooth ID then press to connect.

A connected sound signal will be heard and the blue led connection indicator will stop blinking and stay steady.

Once the Bluetooth connection is completed, select the music from your Bluetooth device and start playing.

Press the “Source” Button and select to Radio. The FM Radio Frequency will show on the RED LED display.

Press and hold the TU << or TU >> buttons for auto scanning the next available station.

Tune to the desired stations.

Press TU<< to save the stations into program.

Repeat the above steps to save other radio station (Maximum can store up to 20 favorable stations).

Light press TU<< or TU>> to retrieve the stored stations. To go for the next stored station, light press again TU<< or TU>>.

Press the “Source” Button and select to USB. USB will show on the RED LED display.

Insert the USB stick into the side panel marked with “ MP3 ”.

Select your favorable music by pressing TU<< or TU>>.

Press “REP” to repeat once for the current song. Press again “REP” to repeat all songs.

If the unit is playing on Bluetooth mode “BT”, it will automatically switch to USB mode once insert the USB stick.

Press the “Source” Button and select to LINE. LINE will show on the RED LED display.

Plug in your 3.5mm cable into the LINE IN put on the side panel and the unit will enter into LINE IN mode.

You can connect any audio device that has 3.5mm audio output jack and playback any audio from the connected device.

The unit comes with a LED indicator alert. If the RED LED is on, it means the battery level is low and recharging is required.

By connecting the AC power, the RED LED will be on, it means the unit is under recharging.

The GREEN LED is on and stays steady when the level of battery is fully recharged.

It is recommended to charge the battery about 6 hours before you start using the unit for the first time.

Smart phones/Tablets recharging works only when AC power is using.

Plug in the Power AC Adaptor to the wall outlet.

Plug in your smart phones/tablets USB recharging cable into the side panel marked “PHONE”.

Connect the recharging cable to your smart phones/tablets. Recharging starts.

Unplug your USB recharging cable when your smart phones / tables are fully recharged.

The model allows you to sing-a-long with the songs playing either on BT, USB (MP3) or LINE IN mode and allows 2 microphones at the same time.

Plug in your Microphone cable into the side panel marked “MIC 1 and/or “MIC 2”.

Adjust the MIC Volume “MIC + / MIC – “ on the top control panel.

Adjust the Echo level “ EH + /EH –“ .

Start to sing.

WARNING: If the MIC Volume and ECHO level set too high or to the maximum, be caution with the high pitch reflection tone.

The IEKO APOLLO IK651MF has a built in Equalizer.

Press and select the preset sound effect for your music; FLAT, CLASSIC, POP, ROCK and JEZZ.

No power: Check that AC power cord is securely inserted in the unit and the electrical outlet. Check the Power On/Off switch is turn to On position. If battery is flat, Plug in the AC Power cord to charge and operate.

Keys no response: Turn the Power On/Off switch to Off, and then On again to reset the unit. Unplug the AC Power cord and plug it back again.

No sound heard: Make sure the LINE connected volume is turn to reasonable level. Make sure the Bluetooth connected device output the audio thru BT out. Make sure the Bluetooth connected device volume is turn to reasonable level.

Audio quality is poor (Bluetooth): Bluetooth reception is poor. Move the Bluetooth device nearer to the Speaker.

Make sure both Bluetooth device and Speaker is not connected to any other Bluetooth device.

Make sure the Bluetooth On/Off switch located below Speaker is slide to On position.

Make sure the Blue LED on the Speaker is fast flashing (Pairing mode).

Turn Power switch to Off, and then On again, Press and hold BT button for 2 seconds to enter into pairing mode.