ICLEVER IC-BK08 (02) PDF Document

The specifications for the ICLEVER IC-BK08 are as follows:

The pairing procedure for the ICLEVER IC-BK08 differs slightly depending on the operating system of the device you are connecting to.

For iOS:

1. Turn on the ICLEVER IC-BK08 keyboard by switching the power switch to “ON”.
2. Press the “BT1” key to enter pairing mode for Channel 1. The indicator light will flash blue.
3. On your iPhone/iPad, go to Settings > Bluetooth and turn Bluetooth on.
4. Search for Bluetooth devices and select “iClever BK08 Keyboard” to connect.
5. The indicator light will turn solid blue when connected successfully.

For Android:

1. Turn on the ICLEVER IC-BK08 keyboard by switching the power switch to “ON”.
2. Press the “BT2” key to enter pairing mode for Channel 2. The indicator light will flash blue.
3. On your Android device, go to Settings > Bluetooth and turn Bluetooth on.
4. Search for Bluetooth devices and select “iClever BK08 Keyboard” to connect.
5. The indicator light will turn solid blue when connected successfully.

For Windows:

1. Turn on the ICLEVER IC-BK08 keyboard by switching the power switch to “ON”.
2. Press the “BT3” key to enter pairing mode for Channel 3. The indicator light will flash blue.
3. On your Windows device, go to Settings > Devices > Bluetooth & other devices > Add Bluetooth or other device > Bluetooth.
4. Search for Bluetooth devices and select “iClever BK08 Keyboard” to connect.
5. The indicator light will turn solid blue when connected successfully.

The ICLEVER IC-BK08 supports connection to three devices simultaneously via Channels BT1, BT2, and BT3. To switch between paired devices:

1. Ensure the keyboard is powered on.

2. Press the corresponding channel key (BT1, BT2, or BT3) for the device you wish to use. The indicator light for that channel will light up briefly (or flash if it needs to reconnect) and then turn off.

3. The keyboard is now ready to type on the selected device.

The indicator lights on the ICLEVER IC-BK08 provide status information:

• Power Status Indicator: Lights up when the power switch is turned on and goes off shortly after.
• Pairing Status Indicator: Flashes blue when the keyboard is in pairing mode for a specific channel (BT1, BT2, or BT3). It turns solid blue when successfully paired to a device on that channel.
• Low Battery Indicator: Flashes red when the battery level is low and needs charging. It will light up briefly when charging is initiated.
• Charging Indicator: Stays solid red while charging and turns off when fully charged.

To charge the ICLEVER IC-BK08 keyboard:

1. Insert the micro USB connector end of the charging cable into the charging port on the keyboard.

2. Plug the standard USB end of the charging cable into a USB power source (such as a computer USB port or a USB charger).

3. The Charging Indicator light will stay solid red while charging.

4. When the battery is fully charged, the Charging Indicator light will turn off.

If the ICLEVER IC-BK08 keyboard is not responding or failing to connect, follow these troubleshooting steps:

• Check Power: Ensure the keyboard is turned on. The Power Status Indicator should light up when the switch is flipped.
• Check Battery: Ensure the keyboard has sufficient battery charge. If the Low Battery Indicator is flashing red, charge the keyboard.
• Check Bluetooth on Device: Verify that Bluetooth is enabled on your connecting device (phone, tablet, or computer).
• Re-Pairing: If the keyboard was previously paired but is not connecting, try turning Bluetooth off and on again on your device. You may need to unpair and re-pair the device if connection persists.
• Switch Channels: If you are trying to connect to a second or third device, make sure you press the correct channel key (BT1, BT2, or BT3) and put the keyboard into pairing mode for that channel if necessary.
• Move Closer: Ensure the keyboard is within the 10m effective distance of the paired device.
• Check Device Compatibility: Confirm that your device supports Bluetooth keyboards and is running a compatible operating system (iOS, Android, or Windows).

The ICLEVER IC-BK08 keyboard includes several functional keys for convenience on iOS and Android systems:

The ICLEVER IC-BK08 features an integrated touchpad for cursor control. To use the touchpad:

• Cursor Movement: Slide your finger across the touchpad surface to move the mouse cursor on the screen.
• Left Click: Tap lightly on the touchpad surface once, or press the dedicated left mouse button below the touchpad.
• Right Click: Tap lightly with two fingers simultaneously on the touchpad surface, or press the dedicated right mouse button below the touchpad.
• Scrolling: Place two fingers on the touchpad and move them up or down to scroll vertically.

Note: Touchpad functionality may vary slightly depending on the operating system of the connected device. Not all gestures might be supported by every OS.

The ICLEVER IC-BK08 is designed to conserve battery life by entering sleep mode automatically.

Entering Sleep Mode: If the keyboard is inactive for about 10 minutes, it will automatically enter sleep mode. You can also manually power it off using the physical power switch.

Waking Up: To wake the ICLEVER IC-BK08 from sleep mode, press any key on the keyboard. It will attempt to reconnect to the last paired device. The pairing indicator light may flash briefly during reconnection.

The ICLEVER IC-BK08 supports three major operating systems:

• iOS (e.g., iPhone, iPad)
• Android
• Windows

It is important to note that while the keyboard supports these systems, some special function keys may operate differently or may not be supported depending on the specific version and settings of the host device.

To clear the existing Bluetooth pairing records stored on the ICLEVER IC-BK08 keyboard:

1. Ensure the keyboard is turned on.

2. Press and hold the ‘FN’ key simultaneously with the ‘Delete’ key for about 3 seconds.

3. The indicator lights might flash briefly to confirm that the pairing records have been cleared. The keyboard is now ready to pair with new devices.