HOVER-1 GO-KART HY-ALL-CMB (01) PDF DOCUMENT

The specifications for the HOVER-1 GO-KART HY-ALL-CMB are as follows:

Compatibility: Most 6.5″ scooters

Max Load: See max load of your scooter

Tire Size: 4″ swivel caster

Seat Material: PP

The HOVER-1 GO-KART HY-ALL-CMB comes with the following parts:

(1) Seat Base

(1) Seat Back

(1) Seat Frame

(1) Seat Back Frame

(1) Frame extension

(1) Right Handle Bar

(1) Left Handle Bar

(2) Elastic strap

(4) Spare Elastic straps

Allen Wrench Set: (2) 5mm wheel change, (1) 6mm seat frame assembly

(2) Twist Knob

(6) Small Screws

(2) Large Screws

(2) Large Washers

(1) Flag Set

To assemble your HOVER-1 GO-KART HY-ALL-CMB, please follow these steps:

1. Using the two large screws and two large washers, attach the handle bars to the appropriate sides of the seat frame. Tighten with the included 6mm Allen wrench.

2. Align the holes of the seat base with the seat frame. Secure the seat in place using the included Allen wrench and four small screws.

3. Insert the frame extension into the seat frame. Adjust to your preferred length. Secure the frame extension in place using one twist knob.

4. Align the holes of the seat back with the seat back frame. Secure the seat back in place using the included Allen wrench and two small screws.

5. Insert the seat back frame into the seat frame. Adjust to your preferred length. Secure the seat back frame in place using one twist knob.

6. Your HOVER-1 GO-KART HY-ALL-CMB is now completely assembled.

Before installing, ensure your HOVER-1 GO-KART HY-ALL-CMB is completely assembled. Follow these steps for installation:

1. Place the pedal mounts onto the footpad sensors of your self-balancing scooter with the front wheel facing forward. Ensure the pedal mounts are centered on the footpad sensors of your scooter as much as possible.

2. Using two elastic straps, attach one end of each strap to the hooks on the front of each pedal mount.

3. Wrap both elastic straps under your self-balancing scooter and attach the ends to the hooks on the back of each pedal mount.

4. WARNING: Do not overtighten the straps. Ensure the go-kart is secure to the scooter. Ensure the foam pads are attached to the bottom of the pedal mounts so that the go-kart does not touch the footpad sensors on the scooter.

5. Your HOVER-1 GO-KART HY-ALL-CMB should now be properly installed onto your scooter.

Ensure that your HOVER-1 GO-KART HY-ALL-CMB and scooter are in proper working order each and every time you ride. Follow this checklist:

• Ensure the battery of your scooter is fully charged before riding.

• Ensure that the screws on the HOVER-1 GO-KART HY-ALL-CMB are tightly secured before each ride.

• Check to ensure the tires of your scooter are not worn.

• Check to ensure all connections are maintained on your scooter.

After reviewing the pre-ride checklist, follow the steps below to begin riding your HOVER-1 GO-KART HY-ALL-CMB:

1. Turn on your scooter.

2. Sit comfortably in the HOVER-1 GO-KART HY-ALL-CMB seat.

3. Place your feet onto the foot rests.

4. To move forward: Firmly grip both handle bars and slowly push them downward simultaneously.

5. To brake: When riding, slowly pull both handle bars upwards simultaneously.

6. To reverse: Slowly pull both handle bars upwards simultaneously from a stopped position.

7. To turn left: Push the right handle bar down while holding the left handle bar in a neutral position.

8. To turn right: Push the left handle bar down while holding the right handle bar in a neutral position.

Always use common sense and follow these safety precautions for safe riding:

• For your safety, always wear a properly fitted helmet that meets CPSC or CE safety standards.

• You must wear a safety helmet, knee and elbow pads, and other necessary protective gear.

• Obey all local laws, stop signs, pedestrian crosswalks, etc.

• If riding with friends and multiple HOVER-1 GO-KART HY-ALL-CMBs, ride single file in a straight line.

• Ride defensively; expect the unexpected.

• Give pedestrians the right-of-way.

• Do not ride too close to pedestrians and alert them if you intend to pass them from behind.

• Slow down at all street intersections and look to the left and right before crossing.

• Obey all traffic signals.

• Watch for cars pulling out into traffic and for the sudden opening of car doors.

• Avoid potholes, drainage grates, or other hazards.

• Be careful when riding on soft road edges, gravel, sand, and uneven surfaces. Ride slowly and avoid quick turns on these surfaces.

• Do not make sharp turns as you may drift and overturn the go-kart.

• Never hitch onto other vehicles.

• Do not “stunt” ride or race in traffic.

• Do not weave in and out of traffic or swerve from side to side.

• This product is strictly forbidden to use on roads and highways, unless your local laws state otherwise.

• To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one rider.

• Do not operate near swimming pools or other bodies of water.

It is recommended that you do not ride your HOVER-1 GO-KART HY-ALL-CMB in wet weather. Brakes do not work as well under wet conditions as they do when dry. Additionally, there are electronic components of the scooter that may be damaged if exposed to water.

Helmets save lives. Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride your scooter. In the event of an accident, a helmet can protect you from serious injury and in some cases, even death.

Correct Fitting: Make sure your helmet covers your forehead.

Incorrect Fitting: If your forehead is exposed, the helmet is not fitted correctly and you are vulnerable to serious injury.