HONEYWELL CT32X1 (01) PDF Document

Make sure that your shipping box contains these items:

• CT32 mobile computer

• Rechargeable li-ion battery

• USB charging cable

• Hand strap (optional)

If you ordered accessories for your mobile computer, verify that they are also included with the order. Be sure to keep the original packaging in case you need to return the mobile computer for service.

Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD™ or microSDHC™ memory cards with mobile computers for maximum performance and durability.

The features of the HONEYWELL CT32X1 include:

Front/Top/Side View:

• Imager Window (LED/Laser Aperture)

• Front Camera

• Battery Status/Notification LED

• Scan Status LED

• Touch Panel

• Power Button

• Scan Button

• Volume Button

Back View:

• Laser Safety Label Location

• Camera Lens and Flash

• Battery Cover Latch

• Battery Cover

• I/O Connectors

Under the Battery:

• Microphone

• Nano SIM and/or MicroSD Card Slot

• Speaker

• USB, Type-C Connector

Before initial use, you should remove the protective film from the screen.

Either a nano-SIM card or an embedded SIM (eSIM) is used to activate the phone and connect to a mobile network. To install a nano-SIM card, insert it into the designated nano-SIM card slot located in the battery compartment.

To install an optional microSD card, follow these steps:

1. Open the card holder in the battery compartment.

2. Insert the microSD card into the holder.

3. Close the card holder to secure the card in place.

Note: Always power off the computer before attempting to install or remove a card. It is also recommended to format the microSD card before initial use.

1. Slide the battery cover latch to the unlock position.

2. Insert the top of the battery into the battery compartment first.

3. Press down on the bottom of the battery until it clicks into place.

4. Align the battery cover with the device and press down firmly.

5. Slide the battery cover latch to the lock position to secure the cover.

To attach the optional hand strap:

1. Thread the small loop on one end of the strap through the attachment point at the top of the device.

2. Pass the larger strap through the small loop and pull it tight to secure it.

3. Thread the loop on the other end of the strap through the attachment point at the bottom of the device.

4. Pass the larger strap through the second loop and pull it tight to secure it.

The mobile computer ships with a partially charged battery. Charge the battery with a CT32 charging device for a minimum of 3.5 hours.

Note: Using the computer while charging the battery increases the time required to reach a full charge. If the mobile computer is drawing more current than supplied by the charging source, charging will not take place.

Yes, on models equipped with a USB port, you can use a USB cable to charge the mobile computer from a host device (e.g., laptop or desktop computer). The connected host device must supply a minimum power output of 5V, 0.5A to the CT32, or the battery will not charge.

The power delivered by the charger must be between a minimum of 1.6 Watts required by the radio equipment and a maximum of 14.6 Watts in order to achieve the maximum charging speed.

To turn the computer on:

• Press and hold the Power button for approximately 3 seconds and then release.

To turn the computer off:

1. Press and hold the Power button until the options menu appears.

2. Touch Power Off.

Before removing the battery, always power off the computer. Improper battery replacement or incompatible device usage may result in risk of burns, fire, explosion, or other hazard. Dispose of batteries according to local regulations.

To adjust the amount of time before the display sleeps after inactivity:

1. Swipe up on the touch screen.

2. Select Settings > Display > Screen Timeout.

3. Select the amount of time before the display goes to sleep.

To wake the computer from sleep mode, press and release the Power button.

For optimum performance, avoid reflections by scanning the barcode at a slight angle.

1. Swipe up on the screen.

2. Select Demos > Scan Demo.

3. Point the computer at the barcode.

4. Touch Scan on the screen or press and hold any Scan button. Center the aiming beam over the barcode.

The decode results appear on the screen.

Note: In the Scan Demo app, not all barcode symbologies are enabled by default. If a barcode does not scan, the correct symbology may not be enabled.

To move files between your CT32 and a computer:

1. Connect the CT32 to your computer using a USB charge/communication accessory.

2. On the CT32, swipe down from the top of the screen to see the notifications panel.

3. Touch the Android System notification twice to open the options menu.

4. Select either File Transfer or PTP.

5. Open the file browser on your computer.

6. Browse to the CT32. You can now copy, delete, and move files or folders between your computer and CT32 as you would with any other storage drive (e.g., cut and paste or drag and drop).

You may need to restart the mobile computer to correct conditions where an application stops responding to the system or the computer seems to be locked up.

Standard Restart:

1. Press and hold the Power button until the options menu appears.

2. Select Restart.

To restart if the touch panel is unresponsive:

• Press and hold the Power button for approximately 8 seconds until the computer restarts.