FREE ENGLISH ALLEN & HEATH GPIO (01) PDF DOCUMENT.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF USER GUIDE.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF USER MANUAL.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF OWNER GUIDE.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF OWNER MANUAL.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF REFERENCE GUIDE.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF REFERENCE MANUAL.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH ALLEN & HEATH GPIO (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD ALLEN & HEATH GPIO (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the GPIO device?
GPIO is a general purpose I/O interface for control integration of an AHM, Avantis or dLive system and third party hardware. It offers 8 opto-coupled inputs and 8 relay outputs on Phoenix connectors, in addition to two +10V DC outputs.
How many GPIO modules can be connected to a system?
Up to 8 GPIO modules can be connected to an AHM, Avantis or dLive system via Cat cable, directly or via a network switch.
How are GPIO functions programmed?
GPIO functions are programmed using the AHM System Manager software, dLive Surface / Director software or Avantis mixer / Director software.
What are some application examples for the GPIO?
The GPIO can be configured for a number of install and broadcast applications, including:
• EVAC (alarm / system mute)
• broadcast (on air lights, fader start logic)
• theatre automation (curtains, lights)
In a typical application, inputs can be taken from a third-party switch panel, and outputs can deliver DC for indicator LEDs on a control panel, and switch closure for a screen, projector, and lighting controller.
What are the power requirements for the GPIO unit?
The unit can be powered by the supplied AC/DC adapter or alternatively via Cat5 cable when connected to a PoE source. The PoE network socket is IEEE 802.3af-2003 compliant.
Use only the power supply provided with the product (ENG Electric 6A-161WP12, A&H part code AM10314). The use of a different power supply can cause electrical or fire hazards.
Power Requirement: 12V DC via external PSU, 1A max or PoE (IEEE 802.3af-2003), 0.9A max.
How do I reset the network settings on the GPIO?
To reset the network settings, hold down the recessed Network Reset switch whilst powering up the unit. This will reset the network settings to the default IP address 192.168.1.75 with subnet 255.255.255.0.
What do the status LEDs on the GPIO indicate?
The status LEDs confirm the following:
• Pwr: Power
• Lnk: Physical connection
• Act: Network activity
What are the input and output specifications of the GPIO?
Inputs: 8x opto-coupled inputs, switching to ground.
Outputs: 8x relay outputs and 2x 10V DC outputs. All relay outputs are normally open by default.
How can I configure an output to be Normally Closed (N/C)?
Output 1 can be configured to be normally closed instead of the default normally open. To do this, you must modify the internal PCB:
1. Cut solder link LK11 on the internal PCB.
2. Solder link LK10.
How can the GPIO unit be installed?
GPIO can be used free standing or up to two units can be installed in a 1U rack space using the optional rack ear kit FULLU-RK19.
What are the cabling requirements for the GPIO network connection?
STP Cat5 or higher cables are required, with a maximum cable length of 100m per connection. The GPIO and its network connection are for indoor use only.
What are the technical specifications of the GPIO?
| Relay Output Max Voltage | 24V |
| Relay Output Max Current | 400mA |
| External Power Output | +10VDC / 500mA max |
| Operating Temperature Range | 0°C to 35°C (32°F to 95°F) |
| Power Requirement | 12V DC via external PSU, 1A max or PoE (IEEE 802.3af-2003), 0.9A max |
What are the dimensions and weight of the GPIO unit?
| W x D x H x Weight | 171 x 203 x 43 mm (6.75″ x 8″ x 1.7″) x 1.2kg (2.7lbs) |
| Boxed | 360 x 306 x 88 mm (14.25″ x 12″ x 3.5″) x 3kg (6.6lbs) |
What is the minimum dLive firmware required for GPIO?
GPIO requires dLive firmware V1.6 or higher.
What should I do before operating the device?
Read the Safety Instructions Sheet included with the product and the information printed on the panel before operating.
CLICK HERE TO DOWNLOAD ALLEN & HEATH GPIO (01) PDF DOCUMENT