GULIKIT ES (01) PDF Document

The indicator light on the GULIKIT ES controller signifies the following statuses:

Orange: Charging

Green: Fully charged

Flashing light: Pairing mode

Solid White: No custom settings configured

Solid Blue: Custom settings configured

To power the controller on, press the Home Button. To power it off, press and hold the Home Button.

The controller will also automatically power off after 15 minutes of inactivity. However, when connected via USB or when Auto-Continuous Fire (Turbo) is active, the controller will not power off automatically.

Follow these steps to calibrate the joysticks:

1. While the controller is powered on, press and hold the “L,” “R,” “D-pad Left,” and “B” buttons simultaneously for 6 seconds to enter calibration mode.

2. During calibration, rotate both the left and right joysticks in full circles 2 to 3 times.

3. Once calibration is complete, the controller will vibrate once to indicate success and will automatically exit calibration mode.

To pair your GULIKIT ES with a PC via Bluetooth (730Hz Polling Rate), follow these steps. This requires your computer to have Bluetooth functionality.

a. Switch the controller to PC mode using the slide switch. Then press and hold the pairing button for 2 seconds until the indicator light begins flashing rapidly, indicating that pairing mode has started.

b. On your computer, open the Bluetooth settings, search for new devices, and select “GuliKit XW Controller” to pair.

c. Once the interface displays “Connected”, the pairing is complete.

To establish a wired connection with a 1000Hz Polling Rate:

1. Set the controller to PC mode.

2. Connect one end of the USB-C to USB-A data cable to the controller.

3. Insert the other end into a USB-A port on your computer.

1. Set the controller to PC mode.

2. Press and hold the pairing button for 2 seconds until the indicator light starts blinking quickly, indicating that pairing mode has been activated.

3. On your phone, go to Bluetooth settings, search for new devices, and select “GuliKit XW Controller”.

4. The interface displaying “Connected” to the new controller indicates that the pairing is complete.

1. Set the controller to NS mode, turn it on, then press and hold the pairing button for 2 seconds. The indicator light will blink quickly, indicating that pairing has started.

2. On the Switch console, navigate to the controller pairing interface by selecting “Controllers” from the Home Menu, then “Change Grip/Order”.

3. Once the interface shows that a new controller is connected, the pairing is complete.

All customized settings require holding the Setting button (gear icon) while pressing the corresponding buttons for the desired function. When customized settings are configured, the indicator light will turn solid blue. When no customized settings are configured, the indicator light will remain solid white.

When the battery is low, the indicator light will flash, and the vibration function will automatically turn off. Once the battery level is restored, the vibration function will turn back on automatically.

To clear all settings and reset the controller, press and hold the Setting button (gear icon) and the Minus (-) button simultaneously. A long vibration indicates that the reset process is complete and the controller has been restored to its default settings.

To change the dead zone setting, press and hold the Setting button (gear icon) and the Left Stick button (press down on the joystick) simultaneously. The controller will vibrate to indicate the new setting:

One vibration: Dead zone enabled on joysticks.

Long vibration: Dead zone disabled on joysticks (Default).

To configure the Turbo setting for the A, B, X, Y, R, or ZR buttons, press and hold the Setting button (gear icon) plus the desired button. The controller will vibrate to indicate the mode set:

One vibration: Manual Turbo Mode – Continuous fire is activated while holding the button and stops when released.

Two vibrations: Auto Turbo Mode – Press the button once to start continuous fire, and press it again to stop.

Long vibration: Disables both manual and auto turbo modes (Default).

To adjust vibration, press and hold the Setting button (gear icon) and press Up or Down on the D-pad to cycle through the options. The controller will vibrate to indicate the selected intensity:

One vibration: Weak vibration.

Two vibrations: Standard vibration (Default).

Three vibrations: Strong vibration.

Long vibration: Turn off vibration.

Yes. This product contains small parts (such as buttons, joystick caps, and screws) that may pose a choking hazard if swallowed by children.