GRUNDIG GKPN66840 LXPW (01) PDF Document

The GRUNDIG GKPN66840 LXPW refrigerator is intended for operating interiors, such as households or similar environments like staff kitchens in stores, offices, farm houses, units of hotels, motels or other resting facilities used by customers, or hostels, and similar non-retail applications. It is not intended for commercial use and should not be used out of its intended purpose. It must not be used in open or enclosed external environments such as vessels, balconies or terraces.

This product may be used by children aged 8 years and older and persons with underdeveloped physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a the product safe way and the hazards involved. Children between 3 and 8 years are allowed to put and take out food to/from the cooler product. Electrical products are dangerous for children and pets. Children and pets must not play with, climb on, or enter the product. Cleaning and user maintenance should not be performed by children unless there is someone overseeing them. Keep the packaging materials away from children (Risk of injury and suffocation). Before disposing of old products that shall not be used any more: 1. Unplug the power cord from the mains socket. 2. Cut the power cord and remove it from the appliance together with the plug. 3. Do not remove the racks and drawers from the product to prevent children from getting inside the appliance. 4. Remove the doors. 5. Store the product so that it shall not be tipped over. 6. Do not allow children to play with the scrapped product. Do not dispose of the product by throwing it into fire (Risk of explosion). If there is a lock available in the product’s door, keep the key out of children’s reach.

The product shall not be plugged into the outlet during installation, maintenance, cleaning, repair, and transportation operations. If the power cord is damaged, it shall be replaced by authorized service only to avoid any risk that may occur. Do not tuck the power cord under the product or to the rear of the product. Do not put heavy items on the power cord. The power cord should not be bent, crushed, and come into contact with any heat source. Do not use an extension cord, multi-plug or adaptor to operate your product. Portable multi sockets or portable power supplies may overheat and cause fire; thus, do not have a multi-plug behind or in the vicinity of the product. The plug shall be easily accessible. If this is not possible, a mechanism that meets the electrical legislation and that disconnects all terminals from the mains (fuse, switch, main switch, etc.) shall be available on the electrical installation. Do not touch the plug with wet hands. When unplugging the appliance, don’t hold the power cord, but the plug.

This product is heavy; do not handle it by yourself. Do not hold the product from its door while handling the product. Be careful not to damage the cooling system and the pipes while handling the product. Do not operate the product if the pipes are damaged, and contact an authorized service.

Contact the Authorized Service for the product’s installation. To prepare the product for installation, see the information in the user guide and make sure the electric and water utilities are as required. If the installation is not suitable, call a qualified electrician and plumber to have them make the necessary arrangements. Otherwise, electric shock, fire issues with the product, or injuries may occur. Check for any damage on the product before installing it. Do not have the product installed if it is damaged. Place the product on a level and hard surface and balance with the adjustable legs. Otherwise, the refrigerator may tip over and cause injuries. The product shall be installed in a dry and ventilated environment. Do not keep carpets, rugs, or similar floor covers under the product (This may cause risk of fire as a result of inadequate ventilation!). Do not block or cover ventilation holes. Otherwise, power consumption may be increased, and damage to your product may occur. Do not connect the product to supply systems such as solar power supplies. Otherwise, damage to your product may occur as a result of the abrupt voltage fluctuations! The more refrigerant a refrigerator contains, the bigger its installation room shall be. In very small rooms, a flammable gas-air mixture may occur in case of a gas leak in the cooling system. At least 1 m³ of volume is required for each 8 grams of refrigerant. The amount of the refrigerant available in your product is specified in the Type Label. The installation place of the product shall not be exposed to direct sunlight, and it shall not be in the vicinity of a heat source such as stoves, radiators, etc. If you cannot prevent installation of the product in the vicinity of a heat source, you shall use a suitable insulation plate, and the minimum distance to the heat source shall be as specified below: At least 30 cm away from heat sources such as stoves, heating units, and heaters, etc., and at least 5 cm away from electric ovens. Your product has the protection class of I. Plug the product in a grounded socket that conforms with the Voltage, Current, and Frequency values specified in the type label. The socket outlet shall be equipped with a fuse with a rating of 10 A – 16 A. The company shall not be responsible for the damages that shall be incurred as a result of operating the product without ensuring ground and electrical connections made as per local or national regulations. The product’s power cable must be unplugged during installation. Otherwise, risk of electric shock and injury may occur! Do not plug the product to loose, broken, dirty, greasy sockets or sockets that have come out their seats or sockets with a risk of water contact. Place the power cord and hoses (if available) of the product so that they shall not cause a risk of tripping over. Penetration of humidity to live parts or to the power cord may cause short circuit. Thus, do not use the product in humid environments or in areas where water may splash (e.g., garage, laundry room, etc.). If the refrigerator is wet by water, unplug it and contact an authorized service.

Do not connect your refrigerator to power saving devices (These systems are harmful for the product). Do not use chemical solvents on the product (These materials contain an explosion risk). In case of a failure of the product, unplug it and do not operate until it is repaired by the authorized service (There is a risk of electric shock!). Do not place a source of flame (e.g., candles, cigarettes, etc.) on the product or in the vicinity of it. Do not get on the product (Risk of falling and injury!). Do not cause damage to the pipes of the cooling system using sharp and piercing tools. The refrigerant that sprays out in case of puncturing the gas pipes, pipe extensions or upper surface coatings may cause irritation of skin and injuries of the eyes. Do not place and operate electric appliances inside the refrigerators/deep freezer unless it is advised by the manufacturer. Do not jam any parts of your hands or your body to the moving parts inside the product. Be careful to prevent jamming of your fingers between the refrigerator and its door. Be careful while opening or closing the door if there are children around. Do not put ice cream, ice cubes, or frozen food to your mouth as soon as you take them out of the freezer (Risk of frostbite!). Do not touch the inner walls, metal parts of the freezer, or food kept inside the refrigerator with wet hands (Risk of frostbite!). Do not place soda cans or cans and bottles that contain fluids that may be frozen to the freezer compartment (Cans or bottles may explode. Risk of injury and material damage!). Do not use or place materials sensitive against temperature such as flammable sprays, flammable objects, dry ice, or other chemical agents in the vicinity of the refrigerator (Risk of fire and explosion!). Do not store explosive materials such as aerosol cans with flammable materials inside the product. Do not place cans containing fluids over the product (Splashing of water on an electrical part may cause the risk of an electric shock or a fire). This product is not intended for storage and cooling of medicines, blood plasma, laboratory preparations, or similar materials and products that are subject to the Medical Products Directive. If the product is used against its intended purpose, it may cause damage to or deterioration of the products kept inside. If your refrigerator is equipped with blue light, do not look at this light with optical devices. Do not stare directly at UV LED light for a long time (Ultraviolet rays may cause eye strain). Do not fill the product with more food than its capacity (Injuries or damages may occur if the contents of the refrigerator falls when the door is opened). Similar problems may occur when an object is placed over the product. Ensure that you have removed any ice or water that may have fallen to the floor to prevent injuries. Change the locations of the racks/bottle racks on the door of your refrigerator while the racks are empty only (Danger of physical injury!). Do not place objects that may fall/tipped over on the product (These objects may fall while opening or closing the door and cause injuries and/or material damages). Do not hit or exert excessive pressure on glass surfaces (Broken glass may cause injuries and/or material damages). The cooling system in your product contains R600a refrigerant. The refrigerant type used in the product is specified in the type label. This gas is flammable. Therefore, be careful not to damage the cooling system and the pipes while operating the product. In case of damage to the pipes: Do not touch the product or the power cord. Keep the product away from potential sources of fire that may cause the product to catch fire. Ventilation the area where the product is placed. Do not use a fan. Contact authorized service. If the product is damaged and you observe gas leak, please stay away from the gas (Gas may cause frostbite if it contacts your skin).

Do not pull by the door handle if you shall move the product for cleaning purposes (Handle may cause injuries if it is pulled too hard). Do not clean the product by spraying or pouring water on the product and inside the product (Risk of electric shock and fire). Do not use sharp or abrasive tools to clean the product. Do not use materials such as household cleaning agents, detergents, gas, gasoline, alcohol, wax, etc. Use cleaning and maintenance agents that are not harmful for food only inside the product. Do not use steam or steamed cleaning materials for cleaning the product and thawing the ice inside it (Steam contacts the live areas in your refrigerator and causes short circuit or electric shock!). Take care to keep water away from the electronic circuits or lighting of the product. Use a clean, dry cloth to wipe the dust or foreign material on the tips of the plugs. Do not use a wet or damp piece of cloth to clean the plug (Otherwise, risk of fire or electric shock may occur).

Follow the safety warnings even if you are away from the product while operating the product via the HomeWhiz app. Also, pay attention to the warnings in the app.

Contact an authorized service when you shall replace the LED / bulb using for lighting.

When operating the GRUNDIG GKPN66840 LXPW refrigerator for the first time, observe the following instructions during the initial six hours: The door should not be opened frequently. It must be operated empty without any food in it. Do not unplug your refrigerator. If a power failure occurs out of your control, please see the warnings in the “Recommended solutions for the problems” section.

Since hot and humid air will not directly penetrate into the product when the doors are not opened, the product will optimize itself in conditions sufficient to protect your food. Functions and components such as compressor, fan, heater, defrost, lighting, display and so on will operate according to the needs to consume minimum energy under these circumstances.

In case of multiple options are present glass shelves must be placed so that the air outlets at the backwall are not blocked, preferably air outlets are remaining below the glass shelf. This combination may help improving air distribution and energy efficiency.

In some models, the instrument panel automatically turns off 1 minute after the door has closed. It will be reactivated when the door has opened or pressed on any key.

Due to temperature change as a result of opening/closing the product door during operation, condensation on the door/body shelves and the glass containers is normal.

This indicator (!) shall be active when your refrigerator cannot perform adequate cooling or in case of any sensor error. On the freezer compartment temperature indicator the letter “E” and on the cooler compartment temperature indicator the numbers 1, 2, 3 will be displayed. The numbers on the indicator specifies the service regarding the failure. If you place hot food in the freezer compartment or leave its door open for a prolonged time, an exclamation mark can be lit. This is not a fault, this warning shall be removed when the food is cooled down or when any key is pressed.

Energy saving function is enabled automatically and the energy saving symbol ( ) is displayed when the door of the product is not opened or closed for some period of time. When the energy saving function is active, all symbols on the screen other than the energy saving symbol shall be turned off. When the energy-saving function is active, pressing any key or opening the door will deactivate the energy saving function and the display signals will return to normal. The energy-saving function is a function activated ex-factory and cannot be cancelled.

This button ( ) is utilized to connect wirelessly to your appliance through HomeWhiz mobile application. If the button is pressed for a long time (3 secs) the LED on the button will blink (in 0.5 second intervals). The link between the appliance and the home network is initialized. After the wireless connection with the appliance is established the LED will be lit solid. After initial setup, the connection can be activated/deactivated by pressing this button. The LED on the button shall flash quickly (at 0.2 second intervals) until the connection is established. When the connection is active, the LED shall light up continuously. If the connection cannot be established for a long period, check your connection settings and refer to the “Troubleshooting” section provided in the user manual. HomeWhiz application shall be used for wireless connection. The steps for setup are explained through the application during setup. You can access the application by scanning the QR code on the HomeWhiz label on the appliance. The application can be obtained from App Store or from Play Store for Android devices. For details visit https://www.homewhiz.com/.

The Cooling Compartment Temperature Setting Key allows setting of temperature for cooler compartment ( ). Pressing this key will enable the cooling compartment temperature to be set at 8,7,6,5,4,3,2 and 1 °C.

Temperature setting is made for cooler compartment. Pressing the ( ) key will enable the freezer compartment temperature to be set at -18,-19,-20,-21,-22,-23,-24 °C.

Press this button for 3 seconds to activate/deactivate the anti-odour ( ) feature. As the anti-odour feature is active, the LED on the respective button is lit. When the feature is active, the anti-odour module will be operated periodically. To maintain efficient performance, it is recommended to have the filter in the deodoriser module by the authorised service provider every 5 years.

When the quick freeze key is pressed, the LED on the key is illuminated and the quick freeze function shall be activated. Freezing compartment temperature is set to -27 °C. Press the key again to cancel function. The quick freezing function shall be automatically cancelled after 24 hours. To freeze a large amount of fresh food, press the quick freeze key before placing the food in the freezer compartment.

Pressing compartment conversion key ( ) for 3 seconds, the freezer section switches between cooler, off and freezer modes. If it is operated as the cooler compartment, the temperature will be set as 4 °C. In case of OFF mode, compartment temperature indicator shall display “- -”.

To activate vacation function ( ), press the button for 3 seconds. The vacation mode will be activated and the LED on the button will be lit. “- -” shall be displayed on the Cooling Compartment temperature indicator and the cooling compartment does not actively perform cooling. You shall not keep your food in the cooling compartment when this function is activated. The other compartments continue to cool according to the set temperatures. Press the key for 3 seconds again to cancel this function.

To reset wireless connection settings press Quick freezing ( ) and wireless connection ( ) buttons must be pressed for 3 seconds. On the appliance where the wireless connection settings are reset/returned to factory defaults, any prior user data set on the appliance is lost.

To change the Bulb/LED used for illumination of your refrigerator, call your AuthorisedService. The lamp(s) used in this appliance is not suitable for household room illumination. The intended purpose of this lamp is to assist the user to place foodstuffs in the refrigerator/freezer in a safe and comfortable way. The lamps used in this appliance have to withstand extreme physical conditions such as temperatures below -20 °C (only chest and upright freezer).

Door opening direction of your refrigerator can be changed according to the place you are using it. If this is necessary, please call your nearest Authorized Service.

An audio warning will be given when the fridge or freezer compartment door of your product is left open for a certain period of time. This audio warning signal will mute when any button on the indicator is pressed or when the door is closed.

For the blue light, Fruits and vegetables stored in the crispers that are illuminated with a blue light continue their photosynthesis by means of the wavelength effect of blue light and thus preserve their vitamin content. For VitaminZone, Fruits and vegetables stored in crispers illuminated with the VitaminZone technology preserve their vitamins for a longer time thanks to the blue, green, red lights and dark cycles, which simulate a day cycle. If you open the door of the refrigerator during the dark period of the VitaminZone technology, the refrigerator will automatically detect this and enable the blue-green or red light to illuminate the crisper for your convenience. After you have closed the door of the refrigerator, the dark period will continue, representing the night time in a day cycle.

The deodoriser module quickly eliminates the bad smells in your refrigerator before they permeate the surfaces. Thanks to this module, which is placed on the ceiling of the fresh food compartment, the bad odours dissolve while the air is actively being passed on the odour filter, then the air that has been cleaned by the filter is re-emitted to the fresh food compartment. This is achieved thanks to the fan, LED and the odour filter integrated into the module. In daily use, the deodoriser module will turn on automatically on a periodic basis. It is recommended to store aromatic foods (such as cheese, olives and delicatessen foods) in their packaging and sealed to avoid bad odours that may result when smells of various foods get mixed. Besides, it is recommended to take spoiled foods out of the refrigerator quickly to prevent the other foods from getting spoiled and avoid bad odours.

In order to store your fruits and vegetables at ideal humidity conditions, you can change the location of the latch on the crisper. If only fruits and vegetables are stored, set the latch to fruits; if only vegetables are stored, set the latch to vegetables, if mixed items are stored, set the latch to mixed setting.

8 hours before freezing the fresh food activate the Quick Freeze function. To preserve food quality, the food items placed in the freezer compartment must be frozen as quickly as possible, use the rapid freezing for this. Freezing the food items when fresh will extend the storage time in the freezer compartment. Pack the food items in air-tight packs and seal tightly. Make sure the food items are packed before putting in the freezer. Use freezer holders, tinfoil and damp-proof paper, plastic bag or similar packaging materials instead of traditional packaging paper. Mark each food pack by writing the date on the package before freezing. This will allow you to determine the freshness of each pack every time the freezer is opened. Keep the earlier food items in the front to ensure they are used first. Frozen food items must be used immediately after defrosting and should not be frozen again. Do not free large quantities of food at once.

The compartment must be set to at least -18°C for storing frozen foods.

The following table shows the recommended settings:

As per the IEC 62552 standards, the freezer must have the capacity to freeze 4,5 kg of food items at -18°C or lower temperatures in 24 hours for each 100 litres of freezer compartment volume. Food items can only be preserved for extended periods at or below temperature of -18°C. You can keep the foods fresh for months (in deep freezer at or below temperatures of 18°C). The food items to be frozen must not contact the already-frozen food inside to avoid partial defrosting.

The placement of food in the GRUNDIG GKPN66840 LXPW refrigerator is as follows:

| Freezer compartment shelves | Various frozen goods including meat, fish, ice cream, vegetables etc. |

| Cooler compartment shelves | Food items inside pots, capped plate and capped cases, eggs (in capped case) |

| Cooler compartment door shelves | Small and packed food or beverages |

| Vegetable bin | Fruits and vegetables |

| Fresh food compartment | Delicatessen (breakfast food, meat products to be consumed in short notice) |

It provides lower temperature within the refrigerator compartment. Use this bin to store delicatessen (salami, sausages, dairy products, etc.) that requires lower storage temperature or meat, chicken, or fish products for immediate consumption. Do not store fruits and vegetables inside this bin.

The Foldable Wine Rack provides the user storing the wine bottles when needed. To use the section, hold the plastic part and pull it to the following direction slowly. Now the foldable wine rack can be used. It is recommended to store maximum 2 bottles of wine on foldable wine rack. To assemble the foldable wine rack, firstly remove the glass shelf from the Refrigerator. Then hold the plastic part, and push it to any side direction by using plastic part’s front and back areas. Now the product can be used with foldable wine rack if needed. To remove the foldable wine rack, firstly, remove the glass shelf from the refrigerator. Then hold the plastic part and pull it to any sides direction. Now the product can be used without foldable wine rack if needed.

To avoid bad odours, pay attention to following: Keeping the refrigerator clean is important. Food residuals, stains, etc. can cause odour. Therefore, clean the refrigerator with bi-carbonate dissolved in water every few months. Never use detergents or soap. Keep the food in closed containers. Microorganisms spreading out from uncovered containers can cause unpleasant odours. Never keep the food that have passed best before dates and spoiled in the refrigerator.

Do not put liquid oils or oil-cooked meals in your refrigerator in unsealed containers as they damage the plastic surfaces of the refrigerator. If oil is spilled or smeared onto the plastic surfaces, clean and rinse the relevant part of the surface at once with warm water.

The power plug is not fully settled. >>> Plug it in to settle completely into the socket.

The fuse connected to the socket powering the product or the main fuse is blown. >>> Check the fuses.

Condensation on the side wall of the cooler compartment can be caused by: The door is opened too frequently (>>> Take care not to open the product’s door too frequently). The environment is too humid (>>> Do not install the product in humid environments). Foods containing liquids are kept in unsealed holders (>>> Keep the foods containing liquids in sealed holders). The product’s door is left open (>>> Do not keep the product’s door open for long periods). The thermostat is set to too low temperature (>>> Set the thermostat to appropriate temperature).

In case of sudden power failure or pulling the power plug off and putting back on, the gas pressure in the product’s cooling system is not balanced, which triggers the compressor thermic safeguard. The product will restart after approximately 6 minutes. If the product does not restart after this period, contact the service. Defrosting is active (>>> This is normal for a fully automatic defrosting product. The defrosting is carried out periodically). The product is not plugged in (>>> Make sure the power cord is plugged in). The temperature setting is incorrect (>>> Select the appropriate temperature setting). The power is out (>>> The product will continue to operate normally once the power is restored).

The product’s operating performance may vary depending on the ambient temperature variations. This is normal and not a malfunction.

The new product may be larger than the previous one (Larger products will run for longer periods). The room temperature may be high (>>> The product will normally run for long periods in higher room temperature). The product may have been recently plugged in or a new food item is placed inside (>>> The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside. This is normal). Large quantities of hot food may have been recently placed into the product (>>> Do not place hot food into the product). The doors were opened frequently or kept open for long periods (>>> The warm air moving inside will cause the product to run longer. Do not open the doors too frequently). The freezer or cooler door may be ajar (>>> Check that the doors are fully closed). The product may be set to temperature too low (>>> Set the temperature to a higher degree and wait for the product to reach the adjusted temperature). The cooler or freezer door washer may be dirty, worn out, broken or not properly settled (>>> Clean or replace the washer. Damaged / torn door washer will cause the product to run for longer periods to preserve the current temperature).

The freezer compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very high degree (>>> Temperature setting of the cooler compartment has an effect on the temperature in the freezer compartment. Wait until the temperature of relevant parts reach the sufficient level by changing the temperature of cooler or freezer compartments). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently). The door may be ajar (>>> Fully close the door). The product may have been recently plugged in or a new food item is placed inside (>>> This is normal. The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside). Large quantities of hot food may have been recently placed into the product (>>> Do not place hot food into the product).

The ground is not level or durable (>>> If the product is shaking when moved slowly, adjust the stands to balance the product. Also make sure the ground is sufficiently durable to bear the product). Any items placed on the product may cause noise (>>> Remove any items placed on the product). The product’s operating principles involve liquid and gas flows (>>> This is normal and not a malfunction). The product uses a fan for the cooling process (This is normal and not a malfunction). Hot or humid weather will increase icing and condensation (This is normal and not a malfunction). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently; if open, close the door). The door may be ajar (>>> Fully close the door). The ambient weather may be humid, this is quite normal in humid weather (>>> The condensation will dissipate when the humidity is reduced).

The product is not cleaned regularly (>>> Clean the interior regularly using sponge, warm water and carbonated water). Certain holders and packaging materials may cause odour (>>> Use holders and packaging materials without free of odour). The foods were placed in unsealed holders (>>> Keep the foods in sealed holders. Microorganisms may spread out of unsealed food items and cause malodour. Remove any expired or spoilt foods from the product). You must never keep food that has passed its best before dates and is spoiled in the refrigerator.

Food packages may be blocking the door (>>> Relocate any items blocking the doors). The product is not standing in full upright position on the ground (>>> Adjust the stands to balance the product). The ground is not level or durable (>>> Make sure the ground is level and sufficiently durable to bear the product).

The food items may be in contact with the upper section of the drawer (>>> Reorganize the food items in the drawer).

High temperatures may be observed between the two doors, on the side panels and at the rear grill while the product is operating. This is normal and does not require service maintenance! Be careful when touching these areas.

If the problem persists after following the instructions in this section, contact your vendor or an Authorised Service. Do not try to repair the product.

Connecting the product to electronic energy saving systems is harmful because it may damage the product.

For a freestanding appliance: ‘this refrigerating appliance is not intended to be used as a built-in appliance.’

Do not leave the doors of the refrigerator open for long periods. When the doors are open, hot air enters the refrigerator/freezer compartments and the appliance consumes more energy to cool the food.

Do not introduce hot food or drinks in the refrigerator.

Do not overload the refrigerator; cooling capacity will be reduced if air circulation inside is obstructed.

Do not place the refrigerator in locations exposed to direct sunlight. Install the appliance at a distance of no less than 30 cm from heat sources such as hobs, ovens, central heaters, and stoves, and a distance of no less than 5 cm from electric ovens.

Procure to keep the food in closed containers in the refrigerator.

Use always the baskets/drawers that are supplied with the freezer compartment for lower energy consumption and better storage conditions.

The contact of the foods with the temperature sensor in the freezer compartment may increase the energy consumption of the appliance. Thus, any contact with the sensor(s) must be avoided.

You can load the maximum quantity of food in the freezer compartment by removing the freezer drawers. The declared energy consumption value of the refrigerator has been determined with the freezer drawers and the top flap compartment removed, and the grid tray in the lower part of the lower freezer compartment is used for maximum food load. You can use the drawers to store food when needed, which can be more convenient depending on the shape and size of the ingredients.

Defrosting the frozen foods in the refrigerator compartment will save energy and preserve the quality of the food.

Do not block the ventilator grill of the freezer by placing food in front of it.

The temperature of the room where the refrigerator is installed should be at least +5°C. Operating your refrigerator under cooler conditions is not recommended with regard to its efficiency.

If two refrigerators are to be installed side by side, there should be at least 2 cm distance between them.

Please make sure that the interior of your refrigerator is cleaned thoroughly.

Due to temperature change as a result of opening/closing the product door during operation, condensation on the door/body shelves and the glass containers is normal.

In case of multiple options are present glass shelves must be placed so that the air outlets at the backwall are not blocked, preferably air outlets are remaining below the glass shelf. This combination may help improving air distribution and energy efficiency.

Do not unplug your refrigerator.

Original packaging and foam materials should be kept for future transportations or moving.

Your refrigerator should be installed at least 30 cm away from heat sources such as hobs, ovens, central heater and stoves and at least 5 cm away from electrical ovens and should not be located under direct sunlight.

Appropriate air ventilation must be provided around your product in order to achieve an efficient operation. If the product is to be placed in a recess in the wall, pay attention to leave at least 5 cm distance with the ceiling and side walls. Please provide at least 5cm distance for air circulation between the back side of your product and the wall to avoid condensation on the rear panel of product. Your product requires adequate air circulation to function efficiently.

If the product will be placed in an alcove, remember to leave at least 5 cm clearance between the product and the ceiling, rear wall and the side walls. Check if the rear wall clearance protection component is present at its location (if provided with the product). If the component is not available, or if it is lost or fallen, position the product so that at least 5 cm clearance shall be left between the rear surface of the product and the wall of the room. The clearance at the rear is important for efficient operation of the product.

If the product stands unbalanced after installation, adjust the feet on the front by rotating them to the right or left.

Use the plastic wedges in the provided with the product to provide sufficient space for air circulation between the product and the wall. 1. To attach the wedges, remove the screws on the product and use the screws provided with the wedges. 2. Attach 2 plastic wedges on the ventilation cover as shown in the figure.

WARNING: Do not make connections via extension cables or multi-plugs. WARNING: Damaged power cable must be replaced by the Authorized Service Agent. If two coolers are to be installed side by side, there should be at least 4 cm distance between them. The company shall not be liable for any damages that will arise when the product is used without grounding and electrical connection in accordance with the national regulations. Power cable plug must be within easy reach after installation. Do not extension cords or cordless multiple outlets between your product and the wall outlet.

Side walls of your product is equipped with refrigerant pipes to improve the cooling system. Refrigerant with high temperatures may flow through these areas, resulting in hot surfaces on the side walls. This is normal and does not need any servicing. Please pay attention while touching these areas.

When you operate your refrigerator for the first time, please observe the following instructions during the initial six hours: The door should not be opened frequently. It must be operated empty without any food in it. Do not unplug your refrigerator. If a power failure occurs out of your control, please see the warnings in the “Recommended solutions for the problems” section. The refrigerator should be left to run empty without food for 6 hours and the door should not be opened unless absolutely necessary. You will hear a sound when the compressor engages. It is normal to hear the sound even if the compressor is inactive due to compressed liquids and gases in the cooling system. It is normal for the front edges of the refrigerator to be hot. These areas are designed to heat up to prevent condensation. In some models, the instrument panel automatically turns off 5 minutes after the door has closed. It will be reactivated when the door has opened or pressed on any key. Since hot and humid air will not directly penetrate into your product when the doors are not opened, your product will optimize itself in conditions sufficient to protect your food. Functions and components such as compressor, fan, heater, defrost, lighting, display and so on will operate according to the needs to consume minimum energy under these circumstances. If there are multiple options, glass shelves must be placed so that the air outlets at the backwall are not blocked, preferably air outlets are remaining below the glass shelf. This combination may help improving air distribution and energy efficiency.

Since hot and humid air will not directly penetrate into your product when the doors are not opened, your product will optimize itself in conditions sufficient to protect your food. Functions and components such as compressor, fan, heater, defrost, lighting, display and so on will operate according to the needs to consume minimum energy under these circumstances.

The baskets/drawers that are provided with the chill compartment must always be in use for low energy consumption and for better storage conditions.

To preserve food quality, the food items placed in the freezer compartment must be frozen as quickly as possible, use the rapid freezing for this.

Freezing the food items when fresh will extend the storage time in the freezer compartment.

It is recommended to store leafed vegetables such as lettuce and spinach and similar vegetables prone to moisture loss not on their roots but in horizontal position into the vegetable bin as much as possible.

When placing the vegetables, place heavy and hard vegetables at the bottom and light and soft ones on the top, taking into account the specific weights of vegetables.

Do not leave vegetables in the vegetable bin in plastic bags. Leaving them in plastic bags causes vegetables to rot in a short time.

Do not put fruits that have a high ethylene gas production such as pear, apricot, peach and particularly apple in the same vegetable bin with other vegetables and fruits. The ethylene gas coming out of these fruits might cause other vegetables and fruits to mature faster and rot in a shorter period of time.

Ice in the freezing compartment thaws automatically.

Mark each food pack by writing the date on the package before freezing. This will allow you to determine the freshness of each pack every time the freezer is opened. Keep the earlier food items in the front to ensure they are used first.

Frozen food items must be used immediately after defrosting and should not be frozen again.

As per the IEC 62552 standards, the freezer must have the capacity to freeze 4,5 kg of food items at -18°C or lower temperatures in 24 hours for each 100 litres of freezer compartment volume.

Food items can only be preserved for extended periods at or below temperature of -18°C.

The food items to be frozen must not contact the already-frozen food inside to avoid partial defrosting.

Boil the vegetables and filter the water to extend the frozen storage time. Place the food in air-tight packages after filtering and place in the freezer.

Bananas, tomatoes, lettuce, celery, boiled eggs, potatoes and similar food items should not be frozen. In case this food rots, only nutritional values and eating qualities will be negatively affected. A rotting threatening human health is not in question.

Various frozen goods including meat, fish, ice cream, vegetables etc. should be placed on the Freezer compartment shelves.

Food items inside pots, capped plate and capped cases, eggs (in capped case) should be placed on the Cooler compartment shelves.

Small and packed food or beverages should be placed on the Cooler compartment door shelves.

Fruits and vegetables should be placed in the Vegetable bin.

Delicatessen (breakfast food, meat products to be consumed in short notice) should be placed in the Fresh food compartment.

It is recommended to store maximum 2 bottles of wine on foldable wine rack.

Cleaning your fridge at regular intervals will extend the service life of the product.

Unplug the product before cleaning it.

Never use gasoline, benzene or similar substances for cleaning purposes. Never use any sharp and abrasive tools, soap, household cleaners, detergents, gas, gasoline, alcohol, wax, etc. Never use steam or steamed cleaning materials for cleaning the product and thawing the ice inside it.

For non-No Frost products, water drops and frosting up to a fingerbreadth occur on the rear wall of the Fridge compartment. Do not clean it; never apply oil or similar agents on it.

Only use slightly damp microfiber cloths to clean the outer surface of the product. Sponges and other types of cleaning cloths may scratch the surface.

Dissolve one teaspoon of bicarbonate in half litre of water. Soak a cloth with the solution and wring it thoroughly. Wipe the interior of the refrigerator with this cloth and the dry thoroughly.

Make sure that no water enters the lamp housing and other electrical items.

If you will not use the refrigerator for a long period of time, unplug it, remove all food inside, clean it and leave the door ajar.

Use a clean, dry cloth to wipe the dust or foreign material on the tips of the plugs. Do not use a wet or damp piece of cloth to clean the plug (Otherwise, risk of fire or electric shock may occur).

Therefore, clean the refrigerator with bi-carbonate dissolved in water every few months.

Materials that may cause odour are not used in the production of our refrigerators. However, due to inappropriate food preserving conditions and not cleaning the inner surface of the refrigerator as required can bring forth the problem of odour.

Keep the food in closed containers. Microorganisms spreading out from uncovered containers can cause unpleasant odours.

Never keep the food that have passed best before dates and spoiled in the refrigerator.

Do not put liquid oils or oil-cooked meals in your refrigerator in unsealed containers as they damage the plastic surfaces of the refrigerator. If oil is spilled or smeared onto the plastic surfaces, clean and rinse the relevant part of the surface at once with warm water.

Condensation on the side wall of the cooler compartment can be caused by: The door is opened too frequently (>>> Take care not to open the product’s door too frequently). The environment is too humid (>>> Do not install the product in humid environments). Foods containing liquids are kept in unsealed holders (>>> Keep the foods containing liquids in sealed holders). The product’s door is left open (>>> Do not keep the product’s door open for long periods). The thermostat is set to too low temperature (>>> Set the thermostat to appropriate temperature).

In case of sudden power failure or pulling the power plug off and putting back on, the gas pressure in the product’s cooling system is not balanced, which triggers the compressor thermic safeguard. The product will restart after approximately 6 minutes. If the product does not restart after this period, contact the service.

Defrosting is active. >>> This is normal for a fully automatic defrosting product. The defrosting is carried out periodically.

The product is not plugged in. >>> Make sure the power cord is plugged in.

The temperature setting is incorrect. >>> Select the appropriate temperature setting.

The power is out. >>> The product will continue to operate normally once the power is restored.

The product’s operating performance may vary depending on the ambient temperature variations. This is normal and not a malfunction.

The new product may be larger than the previous one (Larger products will run for longer periods). The room temperature may be high (>>> The product will normally run for long periods in higher room temperature). The product may have been recently plugged in or a new food item is placed inside (>>> The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside. This is normal). Large quantities of hot food may have been recently placed into the product (>>> Do not place hot food into the product). The doors were opened frequently or kept open for long periods (>>> The warm air moving inside will cause the product to run longer. Do not open the doors too frequently). The freezer or cooler door may be ajar (>>> Check that the doors are fully closed). The product may be set to temperature too low (>>> Set the temperature to a higher degree and wait for the product to reach the adjusted temperature). The cooler or freezer door washer may be dirty, worn out, broken or not properly settled (>>> Clean or replace the washer. Damaged / torn door washer will cause the product to run for longer periods to preserve the current temperature).

The freezer compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very high degree (>>> Temperature setting of the cooler compartment has an effect on the temperature in the freezer compartment. Wait until the temperature of relevant parts reach the sufficient level by changing the temperature of cooler or freezer compartments). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently). The door may be ajar (>>> Fully close the door). The product may have been recently plugged in or a new food item is placed inside (>>> This is normal. The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside). Large quantities of hot food may have been recently placed into the product (>>> Do not place hot food into the product).

The ground is not level or durable (>>> If the product is shaking when moved slowly, adjust the stands to balance the product. Also make sure the ground is sufficiently durable to bear the product). Any items placed on the product may cause noise (>>> Remove any items placed on the product). The product’s operating principles involve liquid and gas flows (>>> This is normal and not a malfunction). The product uses a fan for the cooling process (This is normal and not a malfunction). Hot or humid weather will increase icing and condensation (This is normal and not a malfunction). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently; if open, close the door). The door may be ajar (>>> Fully close the door). There is condensation on the exterior or between the doors (>>> The ambient weather may be humid, this is quite normal in humid weather. >>> The condensation will dissipate when the humidity is reduced).

The product is not cleaned regularly (>>> Clean the interior regularly using sponge, warm water and carbonated water). Certain holders and packaging materials may cause odour (>>> Use holders and packaging materials without free of odour). The foods were placed in unsealed holders (>>> Keep the foods in sealed holders. Microorganisms may spread out of unsealed food items and cause malodour. Remove any expired or spoilt foods from the product).

Food packages may be blocking the door (>>> Relocate any items blocking the doors). The product is not standing in full upright position on the ground (>>> Adjust the stands to balance the product). The ground is not level or durable (>>> Make sure the ground is level and sufficiently durable to bear the product).

The food items may be in contact with the upper section of the drawer (>>> Reorganize the food items in the drawer).

High temperatures may be observed between the two doors, on the side panels and at the rear grill while the product is operating. This is normal and does not require service maintenance! Be careful when touching these areas.

If the problem persists after following the instructions in this section, contact your vendor or an Authorised Service. Do not try to repair the product.

The technical specifications for Wifi + Bluetooth are:

| Frequency Band: | 2.4GHz (Wi-fi or bluetooth operational) |

| Max. Transmission Power: | < 100mW (Wi-fi or bluetooth operational) |

| Software information: | Quartz_WiFi.XXX |

Arçelik A.Ş. hereby declares that this appliance complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available at the following internet address: Products, From: support.grundig.com

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to official collection point for recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was purchased. Each household performs important role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Please make sure that the interior of your refrigerator is cleaned thoroughly.

It must be operated empty without any food in it.

The door should not be opened frequently.

An audio warning will be given when the fridge or freezer compartment door of your product is left open for a certain period of time. This audio warning signal will mute when any button on the indicator is pressed or when the door is closed.

The intended purpose of this lamp is to assist the user to place foodstuffs in the refrigerator/freezer in a safe and comfortable way.

The lamps used in this appliance have to withstand extreme physical conditions such as temperatures below -20 °C.

If you open the door of the refrigerator during the dark period of the VitaminZone technology, the refrigerator will automatically detect this and enable the blue-green or red light to illuminate the crisper for your convenience. After you have closed the door of the refrigerator, the dark period will continue, representing the night time in a day cycle.

Due to the fan integrated into the module, the noise you will hear during operation is normal.

If you open the door of the fresh food compartment while the module is active, the fan will pause temporarily and resume where it has left off after some time the door is closed again.

In case of power failure, the deodoriser module will resume where it has left off in the total operation duration once the power is back.

In order to store your fruits and vegetables at ideal humidity conditions, you can change the location of the latch on the crisper. If only fruits and vegetables are stored, set the latch to fruits; if only vegetables are stored, set the latch to vegetables, if mixed items are stored, set the latch to mixed setting.

When the quick freeze key is pressed, the LED on the key is illuminated and the quick freeze function shall be activated. Freezing compartment temperature is set to -27 °C.

The quick freezing function shall be automatically cancelled after 24 hours.

If it is operated as the cooler compartment, the temperature will be set as 4 °C.

In case of OFF mode, compartment temperature indicator shall display “- -”.

When vacation mode is activated, “- -” shall be displayed on the Cooling Compartment temperature indicator and the cooling compartment does not actively perform cooling.

You shall not keep your food in the cooling compartment when this function is activated.

To reset wireless connection settings press Quick freezing ( ) and wireless connection ( ) buttons must be pressed for 3 seconds.

On the appliance where the wireless connection settings are reset/returned to factory defaults, any prior user data set on the appliance is lost.

If two refrigerators are to be installed side by side, there should be at least 4 cm distance between them.

Place the product on an even floor surface to prevent jolts.

If the product is to be placed in a recess in the wall, pay attention to leave at least 5 cm distance with the ceiling and side walls.

Please provide at least 5cm distance for air circulation between the back side of your product and the wall to avoid condensation on the rear panel of product.

The fuse connected to the socket powering the product or the main fuse is blown. >>> Check the fuses.

The power plug is not fully settled. >>> Plug it in to settle completely into the socket.

The product will restart after approximately 6 minutes. If the product does not restart after this period, contact the service.

Defrosting is active. >>> This is normal for a fully automatic defrosting product. The defrosting is carried out periodically.

The product is not plugged in. >>> Make sure the power cord is plugged in.

The temperature setting is incorrect. >>> Select the appropriate temperature setting.

The power is out. >>> The product will continue to operate normally once the power is restored.

The product’s operating performance may vary depending on the ambient temperature variations. This is normal and not a malfunction.

The new product may be larger than the previous one. Larger products will run for longer periods.

The room temperature may be high. >>> The product will normally run for long periods in higher room temperature.

The product may have been recently plugged in or a new food item is placed inside. >>> The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside. This is normal.

Large quantities of hot food may have been recently placed into the product. >>> Do not place hot food into the product.

The doors were opened frequently or kept open for long periods. >>> The warm air moving inside will cause the product to run longer. Do not open the doors too frequently.

The freezer or cooler door may be ajar. >>> Check that the doors are fully closed.

The product may be set to temperature too low. >>> Set the temperature to a higher degree and wait for the product to reach the adjusted temperature.

The cooler or freezer door washer may be dirty, worn out, broken or not properly settled. >>> Clean or replace the washer. Damaged / torn door washer will cause the product to run for longer periods to preserve the current temperature.

The freezer compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very low degree. >>> Set the freezer compartment temperature to a higher degree and check again.

The cooler compartment temperature is set to a very high degree (>>> Temperature setting of the cooler compartment has an effect on the temperature in the freezer compartment. Wait until the temperature of relevant parts reach the sufficient level by changing the temperature of cooler or freezer compartments). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently). The door may be ajar (>>> Fully close the door). The product may have been recently plugged in or a new food item is placed inside (>>> This is normal. The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside). Large quantities of hot food may have been recently placed into the product (>>> Do not place hot food into the product).

The ground is not level or durable (>>> If the product is shaking when moved slowly, adjust the stands to balance the product. Also make sure the ground is sufficiently durable to bear the product). Any items placed on the product may cause noise (>>> Remove any items placed on the product). The product’s operating principles involve liquid and gas flows (>>> This is normal and not a malfunction). The product uses a fan for the cooling process (This is normal and not a malfunction). Hot or humid weather will increase icing and condensation (This is normal and not a malfunction). The doors were opened frequently or kept open for long periods (>>> Do not open the doors too frequently; if open, close the door). The door may be ajar (>>> Fully close the door). There is condensation on the exterior or between the doors (>>> The ambient weather may be humid, this is quite normal in humid weather. >>> The condensation will dissipate when the humidity is reduced).

The product is not cleaned regularly (>>> Clean the interior regularly using sponge, warm water and carbonated water). Certain holders and packaging materials may cause odour (>>> Use holders and packaging materials without free of odour). The foods were placed in unsealed holders (>>> Keep the foods in sealed holders. Microorganisms may spread out of unsealed food items and cause malodour. Remove any expired or spoilt foods from the product).

Food packages may be blocking the door (>>> Relocate any items blocking the doors). The product is not standing in full upright position on the ground (>>> Adjust the stands to balance the product). The ground is not level or durable (>>> Make sure the ground is level and sufficiently durable to bear the product).

The food items may be in contact with the upper section of the drawer (>>> Reorganize the food items in the drawer).

High temperatures may be observed between the two doors, on the side panels and at the rear grill while the product is operating. This is normal and does not require service maintenance! Be careful when touching these areas.

If the problem persists after following the instructions in this section, contact your vendor or an Authorised Service. Do not try to repair the product.