GOOLOO GP180 (01) PDF Document

The GOOLOO GP180 features the following components:

1. LED flashlight

2. Power switch button

3. JUMPING PORT (12V)

4. USB output port (5V/2.4A, 9V/2A, 12V/1.5A) Quick Charge

5. USB output port (5V/2.1A)

6. 15V/1A input port

The power switch button turns on the LCD display. The display shows the battery percentage.

There are several indicators on the LCD display:

1. LCD Display description: The press switch button turns on the “BATTERY” display, which shows the battery percentage. A reading of “XX%” indicates that the battery has that percentage of power remaining. A display of “LOW BATTERY RECHARGE” indicates that the power is low and it needs to be recharged.

2. Charging product: The display shows “CHARGING” and the charge light is on when charging. When fully charged, the display shows “CHARGED” and the indicator light is off.

3. LED lighting display: Press the light button to turn on/off and switch the three light modes: Flash light, Strobe light, and SOS signal light.

4. Three output specifications: The GOOLOO GP180 has USB ports for charging devices such as phones and tablets.

5. Car boost display: When you connect the smart clamp to the jump start port and the red/black clamps to the battery terminals, the display will provide status information:

If it displays “SHORT CIRCUIT ON JUMPING PORT,” it indicates the short circuit of the device that should be repaired before use.

If it displays “WARNING CLAMP REVERSED,” it indicates a reversed clamp connection. Please check and send it to professionals if needed.

If it displays “BATTERY LOW RECHARGE,” it indicates the unit’s power is too low to jump start the engine and it should be used after being recharged.

If it displays “JUMP START READY,” it means everything is correct and the boost operation can be started.

When it displays “PRESS BOOST BUTTON,” press the BOOST button to complete the boost operation within 30 seconds.

You can charge the GOOLOO GP180 using either a home adapter or a car adapter.

Charged by Home Adapter:

1. Plug the home adapter into the socket of general specification.

2. Connect the other end of home adapter to the 15V/1A input port.

Charged by Car Adapter:

1. Plug the car adapter into the socket of the cigarette lighter.

2. Connect the other end of car adapter to the 15V/1A input port.

1. Make sure the GOOLOO GP180 is over 60% charged. If it has not been used in more than two months, you should charge it first.

2. Connect the smart cable to the jump starter port.

3. Connect the red clamp to the positive (+) terminal of the car battery and the black clamp to the negative (-) terminal.

4. Start the vehicle.

5. Once the vehicle starts, remove the clamp from the battery.

6. Remove the plug from the jump starter.

If the GOOLOO GP180 fails to jump start a car, please wait for 30 seconds and try it again. If it still does not work, it might be due to the cable defectives.

If the unit is still not full after a whole night of charging, it might be because of the cable defectives.

A defective USB port cannot charge other devices. If it can work, it might be due to the cable defectives.

No, the GOOLOO GP180 cannot charge other devices while it is being charged.

If there is no response when pressing the switch button of the GOOLOO GP180, you can try charging it. Plug the adapter into the 15V/1A input port to activate.

The battery can last for 6-12 months. However, we suggest you recharge the GOOLOO GP180 every 3 months.

Please follow these warnings when using the GOOLOO GP180:

1. Read the instruction manual carefully before using this unit.

2. Jump for 12V vehicles only, it would be a hazard if for other jumping. It is forbidden to use for other machines such as airplane and so on.

3. Caution while using this unit.

4. Do not use this unit if any cable clamp or cord is damaged.

5. Do not use in place of a vehicle battery.

6. Do not use as a battery charger.

7. Do not remain the unit on car battery after cranking the engine.

8. Use the jumping cable provided with this unit only.

9. Make sure the blue plug of the jumper cable is plugged fully into the jumping socket, otherwise, the blue plug would be melted.

10. Make sure all the battery connections are clean and all the clamps are securely connected before jump starting. If the battery terminals on the vehicle are dirty or corroded, the power of the unit will be lessened.

11. Do not jump start when the unit is less than 60%. It could damage the unit by overheating. Give two minutes between attempts. The jumping cable can become overheated and detach as a safety measure.

12. Remove the product from the vehicle battery within 30 seconds after jump starting the engine. If not, it could lead to damage.

13. Do not connect the two clamps together.

14. Do not jump start when 3 to 4 indicator lights are illuminated.

15. Do not use by young or infirm persons without supervision.

16. Do not use as a toy.

17. Do not allow the product to become wet.

18. Do not immerse the product in water.

19. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

20. Do not modify or disassemble the unit. Only a repair technician may repair this unit.

21. Do not expose product to extreme heat or fire.

22. Make sure someone should be within range of your voice or close enough to come to your aid when working with batteries.

23. Remove personal metal items like rings, bracelets, necklaces, etc. when using the unit.

24. Do not drop the unit. If the unit has a sharp blow or is damaged in any other way, check it by a qualified battery technician.

25. Do not store in locations where the temperature may exceed 70°C.

26. Charge only at ambient temperature between 0°C and 60°C.

27. Charge only using the charger provided with this unit.

28. Do not use the unit to jump start a vehicle while charging the internal battery.

29. If this unit is leaking liquid dispose of at proper recycle facility immediately.

30. Under extreme conditions, the battery may leak. If a liquid is leaking from the unit. Do not handle with bare hands. If there is skin contact, wash with soap and water immediately. If the liquid contacts the eye, rinse the eye with cold running water for at least 10 minutes and get medical treatment immediately.

31. The unit contains the lithium based batteries, at end of the product life, dispose the unit according to the local ordinance.

To ensure the longevity and safety of your GOOLOO GP180, please observe the following precautions:

Do Not Submerge In Water

Do Not Disassemble

Do Not Dropping

Avoid Extreme Temperatures

Do Not Place Near or Into Fire

The device has Overcharge/Discharge Fuse Protection and conforms to UL STD.2743.

o: Indicate that the content of harmful substances in all of the non-metal material is below the specified level of MCV (the Standard 2002/95/EC(RoHs))