GOLD METAL 5330EX (01) PDF MANUAL

Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death.

Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

Keep cord and plug off the ground and away from moisture.

Always unplug the equipment before cleaning or servicing.

DO NOT immerse any part of this equipment in water.

DO NOT use a water jet or excessive water when cleaning.

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

To avoid burns, DO NOT touch heated surfaces. DO NOT place or leave objects in contact with heated surfaces.

ALWAYS wear safety glasses when servicing this equipment.

No user serviceable parts inside. Refer servicing to qualified service personnel.

Read and understand operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA.

DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation.

This machine is NOT to be operated by minors.

If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.

If the supply cord is damaged, it must be replaced by a special cord or assembly available from Gold Medal Products Co. or its service agent.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

DO NOT install equipment in an area where a water jet is used.

Unit to be installed in locations where ambient temperatures are between a minimum of 5°C (41°F) and a maximum of 55°C (131°F).

Unit to be installed in locations where it can be overseen by trained personnel.

Install unit on a level surface.

Unit is a Portion Pak Cheese Cup warmer.

Improvements are always being made to Gold Medal’s equipment. This information may not be the latest available for your purposes. General images may be used in manual for reference only.

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company.

Unit designed for warming Portion Pak Cheese containers or prepackaged pretzels. Not for the storage or display of time / temperature control for safety foods.

Manual (Instruction Manual)

Doorknob, Screw, and Washers

Registration and Warranty Card

1. Remove all packaging and tape prior to operation.

2. Place unit on a sturdy, level base for use.

3. Install alternate graphics, if desired.

4. Plastic ties hold the interior racks in place for shipping. Carefully cut the tie for each shelf and allow the bottom shelf to fold down into place on the bottom of the cabinet. Top and middle racks sit on the shelf holders and should be positioned under the mounting bolts as shown (Make sure rack sits on the shelf holder and is positioned under the mounting bolts).

5. Install the doorknob as shown.

6. Units with an IEC Power Cord make sure the IEC Power Cord is properly seated into the IEC receptacle before powering up the machine. See Electrical Requirements section to plug unit into power source for use.

7. Unit should be cleaned prior to use (see Care and Cleaning section).

Plastic ties hold the interior racks in place for shipping. Carefully cut the tie for each shelf and allow the bottom shelf to fold down into place on the bottom of the cabinet. Top and middle racks sit on the shelf holders and should be positioned under the mounting bolts. Make sure rack sits on the shelf holder and is positioned under the mounting bolts.

The following power supply must be provided (reference unit Data Plate for Wattage requirement):

5330: 120 V~, 60 Hz

5330EX: 220-230 V~, 50/60 Hz

A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage requirements). We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine.

It is Gold Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance.

Make sure cord is located to prevent a trip hazard or unit upset. Units with an IEC Power Cord – make sure the IEC cord is properly seated into the IEC receptacle before powering up the machine.

1. Make sure all machine switches are OFF before plugging equipment into receptacle.

2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.

3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.

4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).

5. Install unit in a level position.

The POWER SWITCH supplies power to the heating element. It is a three-position power switch:

I = Low Setting

O = OFF

II = High Setting

(Center Position is OFF)

1. Turn the power switch ON and pre-heat unit for 10 to 15 minutes while empty.

• For warming Portion Pack Cheese Cups, use the “II” high setting.

• For warming prepackaged pretzels, use the “I” low setting.

2. Place product inside cabinet and allow it to preheat for approximately one hour.

Note: Unit designed for prepackaged food products only. Not for the storage or display of time / temperature control for safety foods.

3. Keep door closed if not serving or refilling the unit.

For warming Portion Pack Cheese Cups, use the “II” high setting.

For warming prepackaged pretzels, use the “I” low setting.

Unit designed for prepackaged food products only. Not for the storage or display of time / temperature control for safety foods.

Machine must be properly grounded to prevent electrical shock to personnel.

DO NOT immerse in water. DO NOT clean appliance with a water jet or steam cleaner.

Always unplug the equipment before cleaning or servicing.

To avoid burns, DO NOT touch heated surfaces.

DO NOT place or leave objects in contact with heated surfaces.

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). For any cleaning products used, follow the manufacturer’s instructions on the product. DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine. Ammonia cleaners will damage plastic panels. If needed, only use a non-ammonia cleaner, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

1. Turn Power Switch OFF, unplug the unit, and allow it to cool before cleaning.

2. Wipe interior and exterior surfaces of unit with a clean, SLIGHTLY damp cloth. NEVER USE ABRASIVES on this unit. Ammonia cleaners will damage plastic panels. If needed, only use a non-ammonia cleaner, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Note: Periodically, use a vacuum cleaner and/or a SLIGHTLY damp cloth to clean the air intake as needed.

3. Reinstall any rack removed during cleaning.

Periodically, use a vacuum cleaner and/or a SLIGHTLY damp cloth to clean the air intake as needed.

1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)

2. Use only approved replacement parts when servicing this unit.

3. When ordering, please include part number, part name, and quantity needed.

4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order.

5. Address all parts orders to Parts Department, Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, Ohio 45241-4807.