GE ADVANTIUM PROFILE PSB1200BB-BLACK (01) PDF MANUAL

GE ADVANTIUM PROFILE PSB1200BB-BLACK (01) PDF SUMMARY:

What should I do before beginning the installation?

Read the instructions completely and carefully.

---

What should I do with these instructions?

Save these instructions for the local inspector’s use. Keep these instructions with your Owner’s Manual for future reference.

---

What skill level is required for installation?

Installation of this appliance requires basic mechanical and electrical skills.

---

How long does installation take?

Completion Time -1 Hour.

---

Who is responsible for the proper installation?

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the warranty. See Owner’s Manual for warranty information.

---

Where is the note to the installer?

Be sure to leave these instructions with the Consumer.

---

Where is the note to the consumer?

Keep these instructions with your Owner’s Manual for future reference.

---

For what should I use this oven?

Use this oven only for its intended purpose. Never use the oven for warming or heating a room. Prolonged use of the oven without proper ventilation can be hazardous.

---

What safety measure should I take before beginning installation?

For personal safety, remove the house fuse or oven circuit breaker before beginning installation to avoid severe or fatal shock injury.

---

What weight must the mounting surface be capable of supporting?

For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of the 80-pound oven and 30-pound drawer, plus additional oven loads of up to 50 pounds or a total weight of up to 160 pounds.

---

What should I do if I am installing the Advantium 120V Oven below 36"?

If installing the Advantium 120V Oven below 36", you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces. If installing the Advantium 120V Oven below 36", do not remove the plastic door trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces.

---

What models are available?

Profile Models: PSB1200WW-White*, PSB1200BB-Black, PSB1201SS-Stainless Steel Monogram Models: ZSC1201SS-Stainless Steel, ZSC1202SS-Stainless Steel** *No color-matched drawer available for this model. **This unit cannot be installed with an accessory storage drawer.

---

What tools and parts are required but not supplied?

• #2 Phillips screwdriver
• Hand-held drill
• High-speed drill bit, 3/32" diameter
• 3/8" slot-head screwdriver
• Level
• Saw
• 2 x 4 or 2 x 2 lumber for installing runners or 3/8" plywood for the floor (if required)
• Wood screws or other hardware for installing runner or shelf to support oven (if required)
• Safety glasses or goggles

---

What parts are supplied?

• 6 screws (3 required, 3 extra)
• 5 color-matched screws (4 required, 1 extra)
• Bottom trim (2)

---

What should I consider during advance planning?

• These ovens may be installed directly into a 30" wide oven cabinet.
• Cutout dimensions are NOT the same for installation with or without an accessory storage drawer. Make sure to use the correct cutout when preparing the opening. NOTE: ZSC1202 models CANNOT be installed with an accessory storage drawer. See Installation Preparation Without an Accessory Storage Drawer for this model.
• Allow for clearance to adjacent corners, walls, drawers, etc. The oven must be securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand, or hang on the oven door. If installing the drawer accessory, the drawer must be assembled to the oven prior to installation into the cabinet. See the Accessory Storage Drawer Assembly Instructions.

---

What are the electrical requirements for a single Advantium 120 installation?

This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle. The outlet box should be located within reach of the 48" power cord.

---

Where should I install the junction box?

Install a recessed electrical outlet in the back wall of the opening within 6" of either side and at least 9" above the cutout floor.

---

What is important to know about the power cord?

The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong grounding wall receptacle to minimize the possibility of electric shock. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity. Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the consumer to have it replaced with a properly grounded three-prong wall receptacle. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. DO NOT USE AN EXTENSION CORD.

---

What should I do to prepare the opening without an accessory storage drawer?

The Advantium 120V can be installed in combination with other GE/Monogram appliances. Always follow each product’s Installation Instructions to complete the installation. Single Advantium 120V Installation: Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown. Allow 2-1/8" case trim overlap on the sides, 1-1/16" overlap on the top and 7 /8" overlap on the bottom of the opening for all models. Oven overlaps will conceal cut edges on all sides of the opening. When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium 120V and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides. The support must be level and rigidly mounted, flush with the bottom edge of the cutout.

---

How to prepare the opening when installing over a GE/Monogram Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

---

How to prepare the opening when installing over a GE/Monogram oven: If you are replacing a GE/Monogram electric double oven with the combined installation of an Advantium 12OV and a single oven, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2" minimum shown.

---

How to prepare the opening when installing over a GE/Monogram Oven and Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

---

How to prepare the opening when installing over another GE/Monogram Under-the-Counter (UTC) oven: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 8O-pound oven, plus additional oven loads of up to 50 pounds or a total weight of 130 pounds. If you are mounting an Under-the-Counter GE/Monogram oven over another, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2" minimum shown.

---

How to prepare the opening when installing under a GE/Monogram Microwave Oven and over a Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven, plus additional oven loads of up to 50 pounds or a total weight of 130 pounds.

---

How to prepare the opening when installing beside another GE/Monogram Built-in Speedcook Oven: If you are mounting one Under-the-Counter GE/Monogram oven beside the other, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 4-1/2" minimum shown.

---

How to prepare the opening when installing under a GE/Monogram 30" or 36" Cooktop or Countertop: Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36" or wider base cabinet. No minimum clearance is required between the cooktop and oven. The oven is only approved to be installed under the specific models as labeled on the unit.

---

What should I consider when preparing the opening with an accessory storage drawer?

MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4". MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. The Advantium 120V can be installed in combination with other GE/Monogram appliances. Always follow each product’s Installation Instructions to complete the installation. Single Advantium 120V Installation: Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown. Allow 2-1/8" case trim overlap on the sides, 1-1/16" overlap on the top and 7 /8" overlap on the bottom of the opening for all models. Oven overlaps will conceal cut edges on all sides of the opening. When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium 120V and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides. The support must be level and rigidly mounted, flush with the bottom edge of the cutout.

---

How to prepare the opening when installing with an accessory storage drawer over a GE/Monogram Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

---

How to prepare the opening when installing with an accessory storage drawer over a GE/Monogram Oven: If you are replacing a GE/Monogram electric double oven with the combined installation of an Advantium 120V and a single oven, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2" minimum shown.

---

How to prepare the opening when installing with an accessory storage drawer over a GE/Monogram Oven and Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven and 30-pound drawer, plus additional oven loads of up to 50 pounds or a total weight of 160 pounds.

---

How to prepare the opening when installing with an accessory storage drawer over another GE/Monogram Under-the-Counter (UTC) oven: If you are mounting an Under-the-Counter GE/Monogram oven over another, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2" minimum shown.

---

How to prepare the opening when installing with an accessory storage drawer under a GE/Monogram Microwave Oven and over a Warming Drawer: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details. For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven, plus additional oven loads of up to 50 pounds or a total weight of 130 pounds.

---

How to prepare the opening when installing with an accessory storage drawer beside another GE/Monogram Built-in Speedcook Oven: If you are mounting one Under-the-Counter GE/Monogram oven beside the other, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 4-1/2" minimum shown.

---

How to prepare the opening when installing with an accessory storage drawer under a GE Profile 30" or 36" Cooktop or Countertop: Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36" or wider base cabinet. The oven is only approved to be installed under the specific models as labeled on the unit.

---

What is the first step of the installation instructions?

Remove all packing material and tape. Locate parts package containing mounting screws. Remove the oven from the carton. Do not lift unit by handle or conduit. Two people are required to lift this oven. Open the door and remove any packaging in the oven. If installing the Advantium 120V Oven below 36", you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces. If installing the Advantium 120V Oven with an accessory storage drawer, read the storage drawer assembly instructions to assemble the products together before proceeding to Step 2.

---

What is the second step of the installation instructions?

If installing the Advantium 120V Oven above 36" from the floor, you may remove the plastic trim from the bottom of the door for esthetic purposes if desired. If installing the Advantium 120V Oven below 36", do not remove the plastic door trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces. If installing above 36", remove the 3 screws that secure the plastic trim to the bottom of the door. Discard plastic trim. Replace screws.

---

How do I slide the oven into the cutout?

Two people are required to lift the oven into the opening. Grasp the bottom at the front and rear. DO NOT USE THE HANDLE TO LIFT THE OVEN. DAMAGE WILL OCCUR. Lift and hold the oven at the front of the opening. Hold the oven at an angle and plug in the power cord. Carefully, slide the oven into the cabinet part way. Leave the oven a few inches forward of the cabinet frame. Check to be sure the power cord is not trapped under the oven or along the sides of the oven.

---

How do I install the bottom trim?

If installing the Advantium 120V Oven below 36", you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces. If installing the Advantium 120V Oven with an accessory storage drawer, the bottom trim is not required. Proceed to Step 5. Installation Below 36", align trim tabs on the plastic trim to slots in the bottom of the oven. Installation Above 36", align trim tabs on the plastic or metal trim to slots in the bottom of the oven. Secure the bottom trim to the bottom of the oven using 3 screws provided. If installing with an accessory drawer, see installation instructions on page 17 or instructions that come with the accessory drawer.

---

How do I install the mounting screws?

Slide the oven the remaining way into the opening so that the side flanges and control panel are against the cabinet frame. Make sure that the oven is centered in the opening. Open the door, place a turntable tray in the oven and make sure that the tray in the unit is level. Drill pilot holes through the side flanges. Drive the color-matched screws into the side flanges. It is recommended that the screws be hand tightened. If installing oven with an accessory storage drawer: Open the drawer. Drill pilot holes through the side flanges. Drive color-matched screws into the side flanges. It is recommended that the screws be hand tightened. If installing the Profile Advantium 120V Oven with an accessory storage drawer, you must use the Under-the-Counter (UTC) mounting bracket for the drawer. If installing the Monogram Advantium integrated model ZSC1201 above 36", the UTC mounting bracket for the accessory storage drawer must be used.

---

How do I finalize the installation?

Turn the power on at the source. The interior light should come on when the door is opened. Refer to the Owner’s Manual for operating instructions.

---

What should I do before beginning to install the Advantium® Built-In Accessory Storage Drawer?

Read these instructions completely and carefully. Read the Installation Instructions for the Advantium 120V or 240V oven completely and carefully for cutout dimensions and step-by-step instructions.

---

What should I do with these instructions for the Advantium® Built-In Accessory Storage Drawer?

Save these instructions for local inspector’s use. Keep these instructions with your Advantium 120V or 240V Oven Owner’s Manual for future reference.

---

What skill level is required for the Advantium® Built-In Accessory Storage Drawer installation?

Installation of this appliance requires basic mechanical skills.

---

How long does the Advantium® Built-In Accessory Storage Drawer installation take?

One hour with the installation of an Advantium 120V or 240V oven.

---

Who is responsible for the proper installation of the Advantium® Built-In Accessory Storage Drawer?

Proper installation is the responsibility of the installer.

---

What models of Advantium ovens cannot be installed with an accessory storage drawer?

Advantium 240V model ZSCZZ0ZSS and Advantium 120V model ZSC1202 CANNOT be installed with an accessory storage drawer. See Installation Preparation Without an Accessory Storage Drawer in the Installation Instructions for these models.

---

What tools are required for the Advantium® Built-In Accessory Storage Drawer installation?

• #2 Phillips screwdriver

---

What parts are supplied for the Advantium® Built-In Accessory Storage Drawer installation?

• 2 Side Supports
• Screws (8)
• Screws (color-matched) (5)
• Under-the-Counter Mounting Bracket (1)

---

How to assemble the Advantium Built-In Speedcook Oven?

Remove the drawer from the carton. Remove all packing material and tape. Open the drawer and remove any parts inside. Locate parts.

---

How to install the Under-the-Counter (UTC) Mounting Bracket?

For UTC models PSB1200, PSB1201, and ZSC1201 only. Open the accessory drawer so you have access to the top bracket. Remove the three screws securing the top bracket. Install the new UTC mounting bracket using the screws removed previously. Close the drawer and proceed with the installation.

---

How to assemble the oven to the drawer?

Place the storage drawer on a surface with the front of the drawer hanging over the edge of the surface. Not placing the front edge of the drawer over the edge of the surface may result in damage to the drawer since the front edge of the drawer hangs below the bottom of the drawer. Place the oven on top of the storage drawer. Make sure that the back and sides of the oven align with the back and sides of the drawer. The bottom of the oven side flanges will sit directly in front of the top of the storage drawer side flanges. Remove the front two bottom screws on each side of the oven and the top center screw on each side of the storage drawer. Place the side supports into the tabs on the drawer and secure using the screws supplied and the screws removed in Step C. The oven and storage drawer assembly is now ready to be installed. Return to the Advantium 120V or 240V Built-In SpeedCook Oven Installation Instructions to complete the installation.