Free English FURUNO GP-36 DGPS NAVIGATOR (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD FURUNO GP-36 DGPS NAVIGATOR (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I select the display mode on the FURUNO GP-36 DGPS NAVIGATOR?
To select the display mode, press the [DISP] key until the desired display mode appears. Available modes include Plotter Display, Highway Display, Steering Display, Nav Data Display, Digital Data Display, and Speedometer Display.
How can I enlarge or shrink the display range on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [MENU] key.
2. Press the [ENT] key.
3. Press the Up Arrow to increase the range or the Down Arrow to decrease the range.
4. Press the [ENT] key to close the window.
What is the procedure for shifting the cursor or display on the FURUNO GP-36 DGPS NAVIGATOR?
1. On the plotter display, press the cursor pad to turn on and shift the cursor.
2. Place the cursor on an edge of the screen and use the cursor pad to shift the display.
How do I center my own position on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [MENU] key.
2. Select “SHIP TO CENTER?”.
3. Press the [ENT] key.
How do I enter a Man Overboard (MOB) mark on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [MARK/MOB] key.
2. Select “MOB?”.
3. Press the [ENT] key.
4. Press the [ENT] key again.
How do I register a waypoint using the cursor on the FURUNO GP-36 DGPS NAVIGATOR?
1. Operate the cursor pad to place the cursor on the location where you want to inscribe a waypoint.
2. Press the [ENT] key.
3. Press the [ENT] key.
4. Place the cursor under “MARK”.
5. Press the [ENT] key.
6. Press the Up Arrow or Down Arrow to select the desired mark shape.
7. Press the [ENT] key.
8. Select “Exit?” and then press the [ENT] key.
What are the steps to register a route on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [MENU] key once or twice to display the menu.
2. Select “ROUTES”.
3. Press the [ENT] key.
4. Press the [ENT] key.
5. Press the [ENT] key, select a route waypoint, and press the [ENT] key.
6. Repeat step 5 to enter other waypoints on the route.
7. Select “Exit?” to register the route and finish.
8. Press the [ENT] key to register.
How do I set a destination by cursor on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [GOTO] key.
2. Select “CURSOR?”.
3. Press the [ENT] key.
4. Place the cursor on the position to set as the destination.
5. Press the [ENT] key.
How can I cancel a destination on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [GOTO] key.
2. Select “OFF?”.
3. Press the [ENT] key.
How do I set the Arrival Alarm on the FURUNO GP-36 DGPS NAVIGATOR?
1. Press the [MENU] key once or twice to display the menu.
2. Select “ALARMS”.
3. Press the [ENT] key.
4. Select “ARV/ANC” and press the [ENT] key.
5. Select “ARV” and press the [ENT] key.
6. Press the [ENT] key and enter the arrival alarm range with the cursor pad.
7. Press the [ENT] key.
8. Press the [MENU] key twice to finish.
CLICK HERE TO DOWNLOAD FURUNO GP-36 DGPS NAVIGATOR (01) PDF DOCUMENT