Free English FURUNO GP-31 GPS NAVIGATOR (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD FURUNO GP-31 GPS NAVIGATOR (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I select the display mode on the FURUNO GP-31 GPS NAVIGATOR?
To select the display mode, press the [DISP] key until the desired display mode appears.
How can I enlarge or shrink the display range on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [MENU] key.
2. Press the [ENT] key.
3. Press ▲ to increase; ▼ to decrease.
4. Press the [ENT] key to close the window.
How do I shift the cursor and display on the FURUNO GP-31 GPS NAVIGATOR?
1. On the plotter display, press the cursor pad to turn on and shift the cursor.
2. Place the cursor on an edge of the screen and use the cursor pad to shift the display.
How can I center my own position on the display of the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [MENU] key.
2. Select “SHIP TO CENTER?”.
3. Press the [ENT] key.
How do I enter a Man Over Board (MOB) mark on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [MARK/MOB] key.
2. Select “MOB?”.
3. Press the [ENT] key.
4. Press the [ENT] key again.
What is the procedure for registering waypoints using the cursor on the FURUNO GP-31 GPS NAVIGATOR?
A waypoint can be entered by the cursor using the following procedure:
1. Operate the cursor pad to place the cursor on the location where you want to inscribe a waypoint.
2. Press the [ENT] key.
3. Press the [ENT] key.
4. Place the cursor under “MARK”.
5. Press the [ENT] key.
6. Press ▲ or ▼ to select mark shape desired.
7. Press the [ENT] key.
8. Select “Exit?” and then press the [ENT] key.
How do I register routes on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [MENU] key once or twice to display the menu.
2. Select “ROUTES”.
3. Press the [ENT] key.
4. Press the [ENT] key.
5. Press the [ENT] key, select route waypoint and press the [ENT] key.
6. Repeat step 5 to enter other waypoints on the route.
7. Select “Exit?” to register route and finish.
8. Press the [ENT] key to register.
How can I set a destination using the cursor on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [GOTO] key.
2. Select “CURSOR?”.
3. Press the [ENT] key.
4. Place the cursor on the position to set as destination.
5. Press the [ENT] key.
How do I cancel a set destination on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [GOTO] key.
2. Select “OFF?”.
3. Press the [ENT] key.
How do I set the Arrival Alarm on the FURUNO GP-31 GPS NAVIGATOR?
1. Press the [MENU] key once or twice to display the menu.
2. Select “ALARMS”.
3. Press the [ENT] key.
4. Select “ARV/ANC” and press the [ENT] key.
5. Select “ARV” and press the [ENT] key.
6. Press the [ENT] key and enter arrival alarm range with the cursor pad.
7. Press the [ENT] key.
8. Press the [MENU] key twice to finish.
CLICK HERE TO DOWNLOAD FURUNO GP-31 GPS NAVIGATOR (01) PDF DOCUMENT