FANTTIK E1 NEX WORKSTATION (01) PDF Document

• Avoid moisture, dust, and drop.

• Do not store the product in extreme temperature environment.

• Stay alert, watch what you are doing and use common sense when operating. Do not operate while you are tired or under the influence of drugs, alcohol or medication.

• This product is not a toy and should not be used by kids under 5 years old.

• Do not dismantle the machine by yourself. Have your tool serviced by a qualified repair person or contact us for advice.

1. Blunt Tweezers

2. Angled Tweezers

3. Reverse Tweezers

4. Metal Spudger

5. Spudger

6. Halberd Spudger

7. Flex Extension

8. 5/32-inch (4mm) x L28mm *64

9. Jimmy

10. Opening Tool *3

11. Suction Handle

12. Electric Screwdriver

13. Opening Pick *6

14. Magnetic Pad

The FANTTIK E1 NEX WORKSTATION includes the following main components:

• Screwdriver Bit x 64PCS

• Inner Box of Storage Box x 1

• Precision Screwdriver x 1

• Casing of Storage Box x 1

1. Open the magnetic pad and workstation.

2. Press down the screwdriver located on the side of the workstation hinge to release it.

3. Choose the screwdriver bits and tools you need.

4. Use the Forward/Reverse rotation button:

– Press the ᐱ button to turn in or tighten screws.

– Press the ᐯ button to loosen or remove screws.

The torque knob has three settings:

• When the torque knob is set to the lock symbol (🔒), the device will shut down.

• When the torque knob is set to level L, it is in low torque mode.

• When the torque knob is set to level H, it is in high torque mode.

To use the magnetizer, swipe the screwdriver bit tips a few times in the Magnetizer.

Remove the screwdriver bit from the inner box of the storage box then insert the bit into the bit holder.

• **Low Battery:** If the battery level is below 20% when the screwdriver is in use, the indicator will blink red quickly for 5 seconds and then it will turn off. Please charge the battery in time.

• **Charging:** When charging, the indicator will slowly blink red.

• **Fully Charged:** When the battery is fully charged, the indicator will stay white.

Pressing a rotation button will turn on the LED lights simultaneously. The LED lights will turn off automatically after 10 seconds of no operation.

Parameters of the electric precision screwdriver:

Cause: The torque knob is set to the lock level or the lithium battery level is low.

Solution: Set the knob to level L or H, or charge the battery if necessary.

Cause: The bit size doesn’t match the size of the bit holder.

Solution: Use a bit with C4 specifications.

Cause: High moisture in the storage environment.

Solution: Store it in a dry environment, and apply anticorrosive oil on the surface of the bit.

Cause: The torque mode is not being used properly.

Solution: Please use the low torque level L. If the force is not enough, adjust to the high torque level H, or tighten/loosen by manual force.

Cause: The USB cable isn’t plugged in properly or the specified charging voltage isn’t being used.

Solution: Check whether the charging indicator is on, plug the USB cable in correctly, and use the specified charging voltage.

This appliance is marked in accordance with European Directive 2012/19/EU and the Polish Waste Electrical and Electronic Equipment Act with the symbol of the crossed-out waste container. This indicates that this equipment, after its life time, must not be placed together with other household waste.

This equipment must not be disposed of with household waste. The product must be disposed of by selective collection at a dedicated collection point. Proper handling of waste electrical and electronic equipment contributes to avoiding harmful consequences for human health and the environment due to the presence of hazardous components and improper storage and treatment of such equipment.