Free English EVOLVEO XANY 4 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD EVOLVEO XANY 4 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the frequency range of the EVOLVEO XANY 4?
The frequency range for the EVOLVEO XANY 4 is VHF: 87.5 to 230MHz and UHF: 470 to 698MHz.
What is the receiving range of the EVOLVEO XANY 4?
The EVOLVEO XANY 4 is designed for FM, VHF, and UHF signal reception.
What is the maximum gain of the EVOLVEO XANY 4?
The maximum gain for the EVOLVEO XANY 4 is 50dBi.
What is the output level of the EVOLVEO XANY 4?
The output level of the EVOLVEO XANY 4 is 95dBµV.
What is the output impedance of the EVOLVEO XANY 4?
The output impedance for the EVOLVEO XANY 4 is 75 Ohm.
What is the noise figure of the EVOLVEO XANY 4?
The noise figure of the EVOLVEO XANY 4 is less than or equal to 5dB.
What power supply requirements does the EVOLVEO XANY 4 have?
The EVOLVEO XANY 4 requires a power supply of 12V / 200mA.
What are the installation conditions to ensure the best reception for the EVOLVEO XANY 4?
To ensure the best reception for the EVOLVEO XANY 4, keep the antenna away from sources of interference, such as air conditioners, elevators, hair dryers, and microwave ovens. Place the antenna near windows when using it indoors. Install the antenna as high as possible to reduce potential signal loss caused by interruptions between the antenna and the transmission tower.
How do I connect the EVOLVEO XANY 4 to a power source?
Connect the EVOLVEO XANY 4 power cable to a 230V AC wall socket.
How do I connect the EVOLVEO XANY 4 to a television or set-top box?
Connect the EVOLVEO XANY 4 signal cable to the antenna-input socket of your TV or terrestrial digital set-top box.
How do I confirm the EVOLVEO XANY 4 amplifier is working?
After connecting the power, turn on the power switch on the EVOLVEO XANY 4. The power indicator light will illuminate, showing that the amplifier is working.
How should the rod antennas be positioned for VHF Band I-III signals on the EVOLVEO XANY 4?
For Band I, extend the rod antennas completely. For Band III, shorten the rod antennas to about 16 inches, depending on the channel you want to receive. Move the antennas until you achieve the best signal reception.
How should the EVOLVEO XANY 4 be positioned for UHF Band IV-V signals?
Turn the UHF reflector sideways and turn the UHF dipole in an anticlockwise direction until you receive the best signal on your EVOLVEO XANY 4.
How do I adjust the amplifier gain on the EVOLVEO XANY 4?
To increase the gain on the EVOLVEO XANY 4, turn the gain adjuster knob clockwise. To decrease the gain, turn the knob anticlockwise until you reach the best signal reception.
CLICK HERE TO DOWNLOAD EVOLVEO XANY 4 (01) PDF DOCUMENT