EVERFOCUS EDH5210B (01) PDF DOCUMENT

1. **Do not install the camera near electric or magnetic fields.** Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere with camera operation.

2. **Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein.** Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.

3. **Try to avoid facing the camera toward the sun.** In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination beyond the capability of the camera to compensate.

4. **Keep the power cord away from water and other liquids and never touch the power cord with wet hands.** Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric shock.

5. **Never install the camera in areas exposed to oil, gas or solvents.** Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

6. **Cleaning:** For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.

7. **Do not operate the camera beyond the specified temperature, humidity or power source ratings.** This camera is suitable for indoor operation. Use the camera at temperatures within -10°C~50°C (14°F~122°F) and in an indoor environment; this device is not rated as weather proof. The input power source is 12VDC. The use of properly fused or Class 2 power limited type supplies are highly recommended.

8. **Mounting:** Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind, snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional support for the camera.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate this equipment.

• HDcctv 2.1 Megapixel real time 1920×1080/1280×720 HD video over coax for superlative image detail

• Supports video outputs of 1080p30/25 and 720p60/50 (field select)

• Varifocal 3.6~16mm megapixel lens

• Choice of Day/Night operation or Full Color Images in Low Light

• Provides 3-D DNR to improve picture clarity while enabling DVRs to improve disk storage utilization

• 3-Axis Gimbal for Flexible mounting and positioning

• Easy to use OSD setup menu with an array of options

• Enhanced low light sensitivity increase of up to 8x

• Lens Shading Compensation to offset diminished light transmission through lens periphery for uniform image illumination

• Electronic WDR and HSBLC [Highlight Suppression Back Light Compensation] to handle lighting imbalance and bright areas in the scene

• Digital zoom increases effective lens magnification up to 20X

• Up to 24 Privacy Zones

• Dead pixel compensation for increased clarity and extended service life

• SD TV Out for aim and focus using a standard hand held test monitor

Please be careful when you unpack the box due to the electronics devices inside. Check and make sure that you have all the items listed below inside the original box:

• Camera

• Manual

• Pigtail Cable (Power)

• Mounting Template

• Screws

• Service Video Cable

Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The shipping carton is the safest container in which the unit may be transported. Save it for possible future use.

The dimensions are provided in inches:

• Base Diameter: Ø 5.31″

• Dome Diameter: Ø 3.94″

• Total Height: 3.81″

• Dome Height: 1.77″

• Mounting Hole Distance: Ø 4.27″

The main components and controls accessible after removing the dome cover are:

• **Far/Near Adjustment Knob:** Used to adjust the focus of the lens.

• **Tele/Wide Adjustment Knob:** Used to adjust the zoom (telephoto or wide-angle view).

• **OSD Menu Switch:** A 5-axis joystick used to navigate the On-Screen Display menu.

– **UP, DOWN:** Navigates the menu up or down.

– **LEFT, RIGHT:** Changes the values of the selected menu item.

– **MENU (Press In):** Acts as the selection key or Enter.

• **Service Video Connector:** A port to connect the service video cable for a handheld test monitor.

The main parts involved in the installation are as follows:

1. **Mounting Template:** A guide for drilling mounting holes.

2. **Base:** The main body of the camera that attaches to the mounting surface.

3. **Pan Adjust:** Allows for horizontal (left/right) adjustment of the camera module.

4. **Tilt Adjust:** Allows for vertical (up/down) adjustment of the camera module.

5. **Rotate Adjust:** Allows for rotational adjustment of the camera module.

6. **Cover:** The inner cover for the camera assembly.

7. **Housing Cover:** The outer casing of the camera base.

8. **Dome Cover:** The transparent bubble that protects the lens and camera module.

To connect the EVERFOCUS EDH5210B camera, follow these steps:

1. **Power Connection:** Connect the DC12V In (Black) pigtail cable to a DC12V Adapter.

2. **Main Video Output:** Connect the BNC Female (HDcctv Jack) to a coaxial cable running to an HDcctv DVR or other HDcctv signal equipment.

3. **Service Video Output (for setup):** The camera has a service video connector on the board. You can connect the supplied Test Cable to this port and then to the NTSC Video In on a handheld monitor. This allows for easy aiming and focusing during installation.

NOTE: When installing the camera, make sure that all cable ends and connectors are protected from humidity and other outdoor environments.

The OSD menu allows you to configure various camera settings. The main menu categories are SETUP, EXPOSURE, WHITE BALANCE, WDR/BLC, DNR, DAY & NIGHT, IMAGE, SPECIAL, SYSTEM, Reset Date All, and EXIT.

Below is a detailed breakdown of the menu structure: