ETOE A1322 (01) PDF Document

To ensure safe operation of the ETOE A1322, follow these setup guidelines:

1. To reduce the risk of fire or electric shock, do not expose the device to rain or moisture. Objects filled with liquids, such as vases, should not be placed on the device.

2. Do not place the device on soft surfaces such as tablecloths or carpets, as this could be a fire hazard.

3. Avoid placing the device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.

4. To prevent overheating, do not block or clog the ventilation openings. Never place the device in a confined space and always leave enough space around the device for ventilation.

5. Protect the device against direct sunlight, heat, large temperature fluctuations, and moisture.

6. When the device runs for a long period and the surface becomes hot, shut it down and unplug the power cord. Resume operation only after the device has cooled.

7. Always handle the device with care and avoid touching the lens.

8. Never place heavy or sharp objects on the device or the power cord.

9. To avoid electric shock, do not disassemble the device.

10. Only use attachments or accessories specified by the manufacturer.

11. Under certain conditions, moisture can appear inside the device (such as moving from a cold to a warm area). To avoid this, seal the device in a plastic bag before moving it and wait for one to two hours before taking it out.

Managing the power supply for the ETOE A1322 requires the following precautions:

1. Use only the provided power adapter.

2. Power off the device before removing the power supply from the socket.

3. Protect the power cord from being walked on or pinched, particularly at plugs and the point where it exits the device.

4. Unplug the device during lightning storms or when unused for a long period of time.

5. Before making or changing any connections, ensure that all devices are disconnected from the power outlet.

6. Never touch the power cable or the power connector with wet hands.

To maintain the ETOE A1322, follow these cleaning procedures:

1. Power off the device and remove it from the power supply before cleaning the surface.

2. Use a soft, lint-free cloth. Never use liquid, gaseous, or easily flammable cleansers like sprays, abrasives, polishes, or alcohol. Wipe over the surfaces gently.

3. Do not use any liquid cleaning agents to clean the lens as they may damage the protective coating. Use lens cleaning paper specifically to clean the lens of the projector.

4. Do not make any repairs to the device yourself. Only have your device repaired by an authorized service center.

5. Do not stare at the operating beam, as the bright light may hurt your eyes.

The package for the ETOE A1322 includes the following items:

1. Projector x 1

2. Adapter x 1

3. Adapter AC cord x 1

4. Remote control x 1

5. User manual x 1

The ETOE A1322 features the following physical components and connection ports:

1. Air ventilation (Outlet)

2. Lens

3. Tof (Auto focus sensor)

4. Tripod screw hole (located on the bottom)

5. DC-in port

6. USB port

7. HDMI Port

8. IR receiver

9. Aux Port

10. Indicator light

The ETOE A1322 remote control includes the following functions:

1. Power: Press once to power on; press twice to power off.

2. Signal source selection.

3. Access more options during play (available options depend upon the source).

4. Activate Google Assistant voice service.

5. Projector settings.

6. OK: Confirms a selection or entry.

7. Navigation arrows: Navigate menus or adjust selected content.

8. Back: Return to the previous menu.

9. Projector Homepage.

10. Android TV Homepage.

11. Volume up and down buttons.

12. F+ and F- buttons: Used to adjust the focus manually.

13. Mute: Silences the projector audio.

14. Preset Youtube button.

15. Preset Netflix button.

16. Preset Prime Video button.

17. Preset Disney+ button.

For optimal results with your ETOE A1322, follow these placement tips:

1. Place the projector right towards the projection surface to get a rectangle picture.

2. The projection distance must be between 1.1 meters and 4.1 meters.

3. Check the projection distance and screen size chart in the specifications section to determine the best fit for your space.

To start using your ETOE A1322, follow these steps:

1. Connect the power cord to the outlet. The indicator will light up red.

2. Press the power button once to turn the projector on. The indicator will turn green.

3. Auto Focus: Place the projector towards a suitable surface or wall, and the device will automatically focus the image.

4. Manual Focus: You can manually adjust the focus using the remote control by pressing the F+ or F- buttons until the picture is clear.

The ETOE A1322 offers several settings to customize your viewing experience. Access them by pressing the homepage button on the remote and selecting Settings.

Projection Modes available:

1. Desktop Front Projection

2. Ceiling Front Projection

3. Desktop Rear Projection

4. Ceiling Rear Projection

Zoom Function: Use the remote control to resize the picture from 50% to 100% without physically moving the projector.

The ETOE A1322 supports both Auto and Digital Keystone Correction to restore distorted images to a rectangle.

Auto Keystone Correction: When the image is distorted, the projector will automatically perform correction. If this does not work well, you can use digital methods.

Digital Keystone Correction (Manual):

1. Navigate to Settings, select Projector Settings, then Projector Settings again, and turn off Auto Keystone.

2. Go to Vertical Correction or Horizontal Correction and use the left or right buttons on the remote control to adjust.

Four Point Correction: If the image is stretched or distorted along both axes, go to Projector Settings, select Four Point Correction, choose the corner you need to adjust, and use the navigation buttons.

Keystone Correction Reset: To restore default settings, select Keystone Correction Reset and press OK.

The ETOE A1322 supports various wired connections:

HDMI Playback Device: Connect the projector to a PC, TV stick, TV box, DVD player, or game console using an HDMI cable. Press the Signal Source button on the remote, select HDMI, and press OK.

USB Drive: Plug a USB storage device into the port. You can access files by pressing the Signal Source button and selecting USB, or by installing a media player app like VLC from the Google Play Store to play videos directly from the drive.

Headphones or Speakers: Connect a headphone or speaker using a 3.5mm AUX cable. Plug the cable into the AUX port of the projector and play your media.

Press the options button on the ETOE A1322 remote to access the following on-screen settings:

Image Mode: Standard (natural colors), Light (more detail and sharpness), Soft (warm colors for lower light), or Personal (manual adjustment of Brightness, Contrast, Saturation, Sharpness, and Hue).

Color Temp: Cold, Normal, Warm, or Personal (manual adjustment of Red, Green, and Blue).

Sound Mode: Standard, Music, Movie, or Personal (manual adjustment of frequency bands).

Projection Setting: Access Zoom In/Out, Vertical Correction, Horizontal Correction, Four Point Correction, and Keystone Correction Reset.

The technical specifications for the ETOE A1322 are as follows:

CPU: ARM Quad 64-bit Cortex-A53

Native Resolution: 1920*1080

Throw Ratio: 1.22

Aspect Ratio: 16:9 / 4:3 Adaptive

Speaker: 5W*2 Stereo Speaker

Connection Ports: HDMI*1; USB*1; AUX*1

Zoom: 50%-100%

Keystone Correction: plus or minus 40 degrees

Recommended Ambient: 41 degrees F to 95 degrees F / 5 degrees C to 35 degrees C

Relative Humidity: 15% to 85% (non-condensing)

Power Input: 19V, 3A

Rated Voltage: AC 100 – 240V, 50-60 Hz

Power Consumption: 90W

Installation Options: Ceiling / Tripod Stand Mount with Screw Hole on the Bottom

Audio out: 3.5 mm

The following table provides the relationship between the screen size and the required projection distance for the ETOE A1322:

Screen size (inch)	Width (inch)	Width (cm)	Height (inch)	Height (cm)	Distance (ft)	Distance (cm)
40	34.9	88.6	19.6	49.8	3.5	108.0
60	52.3	132.8	29.4	74.7	5.3	162.1
80	69.7	177.1	39.2	99.6	7.1	216.1
100	87.2	221.4	49.0	124.5	8.9	270.1

The ETOE A1322 includes several additional system settings:

Screen Saver: Automatically starts when the projector sits idle. You can change the default time or turn it off.

Screensaver Video: Select the default screen saver video.

Screensaver Timeout Shutdown: Set a shutdown timer for the projector.

Language Settings: Select the on-screen display language for the projector system.

Restore Factory Settings: Reset your device and restore it to its original factory setting.