EMPAVA EMPV-24WOB21 (02) PDF Document

When using your EMPAVA EMPV-24WOB21 oven, basic safety precautions should always be followed:

1. Proper Installation – Be sure your appliance is properly installed and grounded by a qualified technician.

2. Never Use Your Appliance for Warming or Heating the Room.

3. Do Not Leave Children Alone – Children should not be left alone or unattended in area where appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

4. Wear Proper Apparel – Loose-fitting or hanging garments should never be worn while using the appliance.

5. User Servicing – Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.

6. Storage in or on Appliance – Flammable materials should not be stored in an oven or near surface units.

7. Do Not Use Water on Grease Fires – Smother fire or flame or use dry chemical or foam-type extinguisher.

8. Use Only Dry Potholders – Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.

9. Use Care When Opening Door – Let hot air or steam escape before removing or replacing food.

10. Do Not Heat Unopened Food Containers – Build-up of pressure may cause container to burst and result in injury.

11. Keep Oven Vent Ducts Unobstructed.

12. Placement of Oven Racks – Always place oven racks in desired location while oven is cool. If rack must be moved while oven is hot, do not let potholder contact hot heating element in oven.

13. DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN – Heating elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces of the appliance may become hot enough to cause burns – among these surfaces are- for example, oven vent openings and surfaces near these openings, oven doors, and windows of oven doors.

Additional Warnings:

• The appliance becomes hot during operation. Take care not to touch the hot parts inside the oven.

• Always keep children away from the oven. While in operation direct contact with the oven may cause burns.

• Ensure that small items of household equipment, including connection leads, do not touch the hot oven or the cooktop as the insulation material of this equipment is usually not resistant to high temperatures.

• Do not leave the oven unattended when frying. Oils and fats may catch fire due to overheating or boiling over.

• Do not put pans weighing over 15 kg on the opened door of the oven and pans over 55lb/25kg on the cooktop.

• Do not use harsh cleaning agents or sharp metal objects to clean the door as they can scratch the surface, which could then result in the glass cracking.

• The panels adjacent to the oven must be made of heat-resistant material. Cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 212°F.

• Keep combustible materials, such as paper, etc. at least 3 feet (0.9 meters) from the front sides and rear of the heater.

• Never add cold water to food on a hot universal tray or baking tray or directly onto food in a hot oven. The steam created could cause serious burns or scalding and the sudden change in temperature can damage the enamel.

• The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.

Using energy in a responsible way not only saves money but also helps the environment. Here is how you can save energy with your EMPAVA EMPV-24WOB21 oven:

• Do not uncover the pan too often (a watched pot never boils!).

• Do not open the oven door unnecessarily often.

• Switch off the oven in good time and make use of residual heat. For long cooking times, switch off heating zones 5 to 10 minutes before finishing cooking; this saves up to 20% on energy.

• Only use the oven when cooking larger dishes. Meat of up to 2.2lb/1kg can be prepared more economically in a pan on the cooktop.

• Make use of residual heat from the oven. If the cooking time is greater than 40 minutes, switch off the oven 10 minutes before the end time.

• Important! When using the timer, please set appropriately shorter cooking times according to the dish being prepared.

• Make sure the oven door is properly closed. Heat can leak through spillages on the door seals. Clean up any spillages immediately.

• Do not install the oven in the direct vicinity of refrigerators/freezers. Otherwise, energy consumption increases unnecessarily.

During transportation, protective packaging was used to protect the appliance against any damage. After unpacking your EMPAVA EMPV-24WOB21 oven, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.

Caution! During unpacking, the package pieces, etc. should be kept away from children.

Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

To properly install your EMPAVA EMPV-24WOB21 oven, please follow these requirements:

• The kitchen area should be dry and aired and equipped with efficient ventilation. When installing the oven, easy access to all control elements should be ensured.

• This is a built-in oven, and its back wall and one side wall can be placed next to a high piece of furniture or a wall. Coating or veneer used on fitted furniture must be applied with a heat-resistant adhesive (215°F). This prevents surface deformation or detachment of the coating.

• Make an opening with the dimensions given in the installation diagram for the oven to be fitted.

• Make sure the mains plug is disconnected and then connect the oven to the mains supply.

• Insert the oven completely into the opening without allowing the four screws in the places shown in the diagram to fall out.

Cabinet Opening Dimensions:

• Height: 23.0″

• Width: 22.0″

• Minimum Depth: 22.5″

WARNING: Electrical Shock Hazard. Disconnect power before servicing. Use 8 gauge solid copper wire. Electrically ground oven. Failure to follow these instructions can result in death, fire, or electrical shock. All electrical work should be carried out by a suitably qualified and authorized electrician.

The oven is manufactured to work with single-phase alternating current (120/240V supply system). The neutral conductor is not required for the operation of the appliance.

Installation Steps:

1. Disconnect power.

2. Feed the flexible conduit from the through the opening in the cabinet.

3. Remove junction box cover, if it is present.

4. Install a UL listed or CSA approved conduit connector to the junction box.

5. Route the flexible conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.

6. Tighten screens on conduit connection.

Wiring Connection (for 240V):

The safety wire must be connected to the ground terminal.

• Green Wire connects to Ground.

• Red Wire connects to L1.

• Black Wire connects to L2.

Bellows Wiring Method:

Step 1: Remove the wiring strip.

Step 2: Connect the ground wire, red wire L1 and black wire L2 of the bellows to the ground wire, red wire L1 and black wire L2 of the wiring seat respectively. The bellows is stretched out from the outlet of the bellows and pressed on the upper cover by the wire clamp.

Rack Installation:

Step 1: Insert the bracket into the mounting hole of the inner tank.

Step 2: Insert the bracket into the slot.

Telescopic Runner Installation:

Step 1: Put the four hooks into the side rack.

Step 2: Put the two locks into the side rack.

Before the first use of your EMPAVA EMPV-24WOB21 oven, follow these steps:

1. Remove packaging, clean the interior of the oven.

2. Take out and wash the oven fittings with warm water and a little washing-up liquid.

3. Switch on the ventilation in the room or open a window.

4. Heat the oven to a temperature of 465°F for approximately 30 minutes, remove any stains and wash carefully. Important!

5. The inside of the oven should only be washed with warm water and a small amount of washing-up liquid.

Turn on:

• In shutdown status, touch the On/Off key for more than 3 seconds to enter functions setting status. Touch the key one time to enter standby status.

• In standby status, touch the On/Off key one time to enter functions setting status.

Turn off:

• In working status, touch the On/Off key one time to immediately stop the corresponding function and enter standby status.

• In standby status, touch the On/Off key for more than 3 seconds to enter shutdown status.

The LED displays as “88:88” when in standby status. Note: when the product is first powered on, if the clock is not set, it will show (0:00).

To set the clock on your EMPAVA EMPV-24WOB21 oven (12 hours / 24 hours):

1. Touch the Clock key one time. The hour setting will flicker.

2. Touch the Up or Down arrow keys to set the hours (0-11 for 12-hour / 0-23 for 24-hour). Default is “00”.

3. Touch the Clock key once again. The minute setting will flicker.

4. Touch the Up or Down arrow keys to set the minutes (0-59). Default is “00”.

5. Press and hold the Clock key for more than 4 seconds to switch between the 12-hour and 24-hour system. The default is the 12-hour system.

6. Touch the OK key to finish the clock setting.

Using “Roast” as an example (other functions are set the same way):

1. In standby condition, touch the desired function key (e.g., “Roast”) continuously. The display will show the function, with the “XX” for temperature and time flickering.

2. To set the temperature: Touch the Temperature key. The temperature setting will flicker. Touch the Up or Down arrow key to increase or decrease the temperature in 10°F/5°C increments. Temperature can be set between 104°F and 482°F.

3. To set the time:

• Touch the Clock key once, the hour will flicker. Use the Up or Down arrow keys to set the time between 0 and 8 hours.

• Touch the Clock key again, the minute will flicker. Use the Up or Down arrow key to set minutes between 0 and 59 minutes.

4. Touch the OK key to start the cooking process. Alternatively, if you do not adjust the settings, touching OK will start the oven with the system defaulted or current condition.

The default temperature and time settings vary by cooking function. Below are the tables for models with and without a rotisserie feature.

Table 1 (With rotisserie)

Table 2 (Without rotisserie)

Under the function of temperature display setting, press the Temperature key long for more than 4 seconds. This will allow you to switch between degrees Fahrenheit and degrees Celsius. The default unit is Fahrenheit every time you power on the oven. The corresponding temperature value is automatically converted by the controller.

(1) Lock: Touch the Lock key for more than 4 seconds. The lock icon shows in the LED display, indicating it is locked. There is no function to touch any other keys while locked.

(2) Unlock: Touch the Lock key for more than 4 seconds again. The lock icon will disappear from the display, and the oven is unlocked.

To set a delayed start time on your EMPAVA EMPV-24WOB21 oven:

1. Touch the Delay key once. The hour will flicker.

2. Use the Up or Down arrow keys to set the hour.

3. Touch the Delay key again. The minute will flicker.

4. Use the Up or Down arrow keys to set the minute.

5. Touch the OK key to finish the delay setup.

Caution: Before each cleaning and maintenance, cut off the power supply! Ensure the oven has completely cooled before you start cleaning.

• The oven should be cleaned after every use. When cleaning, the lighting should be switched on to enable you to see the surfaces better.

• The oven chamber should only be washed with warm water and a small amount of washing-up liquid.

• After cleaning the oven chamber, wipe it dry.

• Do not use cleaning products containing abrasive materials for the cleaning and maintenance of the glass front panel.

• It is advisable to use a solution of warm water with a little washing-up liquid or cleaning products for stainless steel sinks.

To use the steam cleaning feature on your EMPAVA EMPV-24WOB21 oven:

1. Pour 250ml of water (1 glass) into a bowl placed in the oven on the first level from the bottom.

2. Close the oven door.

3. Set the temperature to 125°F and the function to the Keep Warm position.

4. Heat the oven chamber for approximately 30 minutes.

5. Open the oven door, wipe the chamber inside with a cloth or sponge, and wash using warm water with washing-up liquid.

Caution! Possible moisture or water residues under the oven can result from steam cleaning.

After cleaning the oven chamber, wipe it dry.

To avoid the possibility of an electric shock, ensure that the appliance is switched off before replacing the bulb.

1. Turn off the oven and disconnect the mains plug.

2. Unscrew and wash the lamp cover and then wipe it dry.

3. Unscrew the light bulb from the socket and replace it with a new one. The new bulb must be a high-temperature bulb (575°F) with the following parameters:

• Voltage: 240 V~

• Power: 15 W

• Thread: E14

4. Screw the new bulb in, making sure it is properly inserted into the ceramic socket.

5. Screw in the lamp cover.

There are multiple methods to disassemble the door glass for cleaning.

Disassembly of Inside Glass

Method 1 (Pointed tool):

1. Insert a pointed tool into the disassembly groove.

2. Drive up the pointed tool bilaterally to loosen the inside glass.

3. Extract the inside glass by sliding it out sideways.

Method 2 (Cross screwdriver):

1. Disassemble two screws on the beam with a cross screwdriver.

2. Move out the beam.

3. Move up the inside glass along with the direction of the arrow.

4. Extract the inside glass by sliding it out sideways.

Method 3 (Manual operation):

1. Insert your index finger into the disassembly groove and pry up the inside glass.

2. Extract the inside glass by sliding it out sideways.

Disassembly of Middle Glass

1. Loosen the screws on the bilateral holders.

2. Slide out the middle glass to finish disassembly.

Assembly of Middle Glass

1. Put the middle glass on the corresponding holders accurately, and tighten the screws.

Assembly of Inside Glass

1. Insert the inside glass into the fixed holder and push it to the fixed position.

2. Press the glass into the snap hook.

In the event of an emergency, you should:

• Switch off all working units of the oven.

• Disconnect the mains plug.

• Call the service center.

Some minor faults can be fixed by referring to the troubleshooting table before calling for service.

If your EMPAVA EMPV-24WOB21 oven does not work, it could be due to a break in the power supply or the back thermostat power-off protection being activated.

• Check the household fuse box. If there is a blown fuse, replace it with a new one.

• Manually reset the back thermostat of the oven.

If the oven lighting does not work, the bulb may be loose or damaged. Tighten up or replace the blown bulb, following the instructions in the “Cleaning and Maintenance” section.

• Voltage rating: 240V~ 60Hz

• Power rating: max. 3200W

• Oven dimensions H/W/D(in): 23.4 / 23.4 / 22.6

• Net weight: Approx. 68lb