EMERSON EM516 (01) PDF Document

The EMERSON EM516 package includes:

• Bluetooth Headset

• User Guide

• Charging Cable

The controls on the EMERSON EM516 headset are as follows:

1. [ ] – Play/Pause and Answer/End calls/LED Indicator light

2. Microphone

3. [V+] – Increase volume

4. [V-] – Decrease volume

5. Charging port

1. Connect the small end of the charging cable into the charging port on the side of the Headset.

2. Connect the other end of the charging cable to your computer’s USB port.

3. The LED indicator light turns RED when charging.

4. The LED indicator light turns OFF when charging is finished.

1. Make sure the EMERSON EM516 is turned off.

2. Keep your EM516 and Bluetooth enabled device within 3 feet of each other during the pairing process.

3. Set your mobile phone or other Bluetooth enabled device to search for Bluetooth devices.

4. Press and hold the [ ] button on the EM516 until the LED Indicator Light flashes RED and BLUE alternately (approximately 6 seconds). The LED Indicator Light will turn BLUE after 3 seconds, but keep holding until the light flashes BLUE and RED.

5. When the Bluetooth enabled device finds the EM516, confirm by selecting EM516 from the list. If asked for a passcode, enter “0000” (four zeroes).

6. After a successful registration, the LED Indicator light will blink BLUE twice quickly every 3 seconds.

On an iPhone: Go to SETTINGS > GENERAL > BLUETOOTH (Make sure Bluetooth is turned ON).

On a Blackberry: Go to SETTINGS/OPTIONS > BLUETOOTH and Enable BLUETOOTH.

On an Android Phone: Go to SETTINGS > BLUETOOTH > MENU > Search for devices (Make sure Bluetooth is turned ON).

On other Cell Phones/Devices: Review the instruction manual that came with your phone/device.

To turn ON: Press and hold the [ ] button for approximately 3 seconds. The LED Light indicator will flash BLUE and the voice prompter will say “Power on.”

To turn OFF: Press and hold the [ ] button for approximately 3 seconds. The LED Light indicator will flash RED, the voice prompter will say “Power off,” and the headset will turn off.

To make a call: Dial the number and press the send button on your mobile phone. The call is automatically transferred to the headset.

To answer a call: Quickpress the [ ] button.

To end a call: Quickpress the [ ] button.

To reject an incoming call: Press and hold the [ ] button for 2 seconds and then release. NOTE: If you hold too long, the headset will turn off.

To redial the last number called: Quickpress the [ ] button twice quickly. The last number called will be redialed. (This feature is dependent on your phone supporting it).

To enjoy wireless music on your EMERSON EM516 Bluetooth Headset, make sure you are connected to a Bluetooth enabled device.

Play/Pause:

• Press the [ ] button to pause the music.

• To resume music playback, press the [ ] button again.

Adjusting the Volume:

• Press the [V+] button to increase the volume.

• Press the [V-] button to decrease the volume.

Changing Tracks:

• In order to play the previous or next song, you must use your Bluetooth enabled device’s controls.

If the Bluetooth enabled device you are using to play music is a mobile phone and you receive a phone call, the music will be interrupted.

1. To accept the call, press the [ ] button. If you accept the call, the conversation will be replayed by the Bluetooth Headset. You can speak into the microphone of the Bluetooth Headset during the conversation. After you have ended the call, the devices will remain connected and playback will continue.

2. To reject an incoming call, press and hold the [ ] button for 2 seconds and then release. If you reject the call, playback will continue.

The battery may be exhausted. Try charging the battery.

• If the Bluetooth Headset is turned OFF, then turn it ON.

• The Bluetooth Headset may not be paired to the Bluetooth enabled device. Try checking whether the connection exists. If necessary, try pairing the Bluetooth enabled device to the Bluetooth Headset again.

• The volume level of the Bluetooth enabled device may be too low. Try increasing the volume of the Bluetooth enabled device.

• Make sure your Bluetooth enabled device supports A2DP profile.

• Turn up the volume on your Bluetooth enabled device.

• For some Bluetooth enabled devices, you must open your Bluetooth settings and make sure “media” is turned ON.

• Make sure the Bluetooth Headset is turned OFF before beginning the pairing process.

• Keep your Bluetooth Headset and Bluetooth enabled device within 3 feet of each other during the pairing process.

• Press and hold the [ ] button on the EM516 until the LED Indicator Light flashes RED and BLUE alternately (approximately 6 seconds). The LED Indicator Light will turn BLUE after 3 seconds, but keep holding until the light flashes BLUE and RED.

• Check that your device’s Bluetooth feature is turned ON.

• Try repeating the pairing process, see “Pairing the EM516”.