EMERSON EM129 (01) PDF Document

The following items are included in the box:

• Bluetooth Headset

• Owner’s Manual

• Earhook

• Micro USB Charging Cable

• Ear Cushions (S), (M), (L)

CAUTION: Although this device enables drivers to conduct handsfree conversations, it is still safer to pull over before using a mobile phone. Always keep your full attention on your driving.

Driving while talking on your mobile phone is dangerous, and illegal in many states. Check local laws regarding the use of a mobile handset and wireless headset while driving. If you use the Bluetooth Headset while driving, ensure your attention and focus remains on your driving.

The EMERSON EM129 headset has the following controls:

• Power button (Power ON/OFF, Answer/end a call)

• Volume up button [+)

• Volume down button [-]

• LED Indicator light

• Micro USB jack

1. Connect the charging pin of the Micro USB cable to the Micro USB jack of the headset.

2. Connect the other end of the Micro USB cable to your computer’s USB port.

3. The RED LED indicator light turns on.

4. When the headset is fully charged (approximately 2-3 hours), the BLUE LED indicator light turns on.

NOTE: Charge your headset for at least 8 hours before using it for the first time.

When the battery is running low, the RED LED Indicator light starts to flash.

1. Make sure the EM129 is turned off.

2. Keep your EM129 and Bluetooth enabled device within 3 feet of each other during the pairing process.

3. Set your mobile phone or other Bluetooth enabled device to search for Bluetooth devices.

• On an iPhone: Go to SETTINGS > GENERAL > BLUETOOTH (Make sure Bluetooth is turned ON).

• On a Blackberry: Go to SETTINGS/OPTIONS > BLUETOOTH and Enable BLUETOOTH.

• On an Android Phone: Go to SETTINGS > BLUETOOTH > MENU > Search for devices (Make sure Bluetooth is turned ON).

4. Press and hold the [Power] button on the EM129 until the LED Indicator Light flashes RED and BLUE alternately (approximately 8 seconds). The LED Indicator Light will turn BLUE after 5 seconds, but keep holding until the light flashes BLUE and RED.

5. When the Bluetooth enabled device finds the EM129, confirm by selecting EM129 from the list. If asked for a passcode, enter “0000” (four zeroes).

6. After a successful registration, the LED Indicator Light will blink BLUE every 8 seconds.

SET ACCESSORY to BLUETOOTH on PS3:

1. Go to the PS3 main menu, scroll to and select “Settings”.

2. Scroll to and select “Accessory Settings”.

3. Scroll to and select “Manage Bluetooth Devices”.

4. The menu will ask: “The Bluetooth device has not been registered. Do you want to register it?”, then select “YES”.

REGISTER EM129 to PS3:

Put your Bluetooth Headset into pairing mode (See “Pairing the headset with a Bluetooth enabled device”).

1. Select “Start Scanning” from the PS3 menu.

2. Once the PS3 has discovered the Headset, the screen will read “Select the Bluetooth device to register”, then select “EM129”.

3. The PS3 will ask for a passkey. Enter [0000] then select “OK”. Now press [O] (the PS3 circle button) to get back to the previous menu.

4. Scroll to and select “Audio Device Settings” to change the “Input Device” to “EM129”.

NOTE: “Input Device” is the microphone, and determines the method of how others will hear you speak. By default, the “Output Device” will now switch to “EM129”. “Output Device” is the audio, and determines how you will hear the PS3 audio and others speaking.

To test the connection, speak into the headset and you will see the bars above the “Microphone Level” moving, if not, repeat the pairing process.

Press “OK” to confirm the new settings. You are now ready to use the Bluetooth Headset with your PS3 Entertainment System. If you would like to hear the PS3 audio through your TV or Audio System, scroll to “Output Device” and switch to “System Default Device”.

• To turn ON, press and hold the [POWER] button until the BLUE LED indicator light flashes three times. When powered on, the BLUE LED indicator light will quickly flash.

• To turn OFF, press and hold the [POWER] button until the LED indicator light flashes solid RED and then shuts off.

If you hold the power button too long when turning the headset on, the light will flash RED and BLUE and the phone will be in pairing mode. If this happens, turn the headset off, then turn it on again.

• To answer a call, press and release the [POWER] button.

• To end a call, press and release the [POWER] button.

Dial the number and press the send button on your mobile phone; the call is automatically transferred to the headset.

Quickpress the [Power] button twice. The last number called will be redialed. This feature is dependent on your phone supporting it.

Press the [+] or [-] buttons to adjust the volume. You may also adjust the volume from your mobile phone’s volume control.

• Make sure the Bluetooth Headset is turned off before beginning the pairing process.

• Press and hold the [Power] button on the EM129 until the LED Indicator Light flashes RED and BLUE alternately (approximately 8 seconds). The LED Indicator Light will turn BLUE after 5 seconds, but keep holding until the light flashes BLUE and RED.

• Make sure that you fully charged the headset before pairing.

• Keep your Bluetooth Headset and mobile phone within 3 feet of each other during the pairing process.

• Check that your phone’s Bluetooth feature is turned ON.

• Try repeating the pairing process.

• Try turning the headset OFF, and then turning it ON again.

• Many mobile phones have an auto reconnect option when first attempting to reconnect to a newly paired Bluetooth device. Make sure you accept this option, so that your Bluetooth Headset automatically reconnects to your mobile phone; check the user guide of your mobile phone for more information regarding this option.

• Try unpairing the headset from your phone, and repeat the pairing procedure.

• For the best audio quality, always wear your Bluetooth Headset on the same side of the body as your mobile phone.

• Check that the battery is charged enough.

Press the [+] and [-] buttons to adjust the volume.