ELETAB ELTGM05-2 (01) PDF Document

The ELETAB ELTGM05-2 is rated for monitors weighing between 1.5kg and 8kg (3.3lbs to 17.6lbs) per arm. It supports a maximum screen size of 32 inches. The mount is compatible with VESA patterns of 75x75mm and 100x100mm.

Please observe the following cautions:

Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.

Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

The following tools are required for assembly:

4mm Allen Wrench (O) (Included)

6mm Allen Wrench (P) (Included)

Wrench (Q) (Included)

Phillips Screwdriver (Not included)

Install the clamp base support (C) onto the base of the monitor stand (A) with bolts (M) using the provided 4mm Allen wrench (O). Then, apply pads (N) to the bottom of the base to prevent the table top from being scratched.

The clamp configuration depends on the thickness of your desk:

For desks with a thickness of 10-55mm: Secure the clamp (D) to the upper two holes with bolts (L) using the 4mm Allen wrench (O).

For desks with a thickness of 50-85mm: Secure the clamp (D) to the lower two holes with bolts (L) using the 4mm Allen wrench (O).

After configuring the clamp, attach the base support cover (E) to the clamp base support (C) and tighten the clamp to the desktop using the plastic knob.

Follow these steps for grommet installation:

1. Slide the long screw (F) through the top of the grommet base support (G) and install it on the base of the monitor stand with bolts (M) using the 4mm Allen wrench (O). Apply pads (N) to the bottom of the base.

2. Position the stand on the desk with the long screw going through the hole.

3. Secure the stand by using the support plate (H) and washer (J) on the underside of the mounting surface.

4. Tighten the nut (I) with the wrench (Q).

Attach the VESA plate (B) to the back of the monitor and secure it with screws (M-A) or (M-C) along with washers (M-E). Avoid excessive tightening of the screws to prevent damage to the monitor.

Attach the VESA plate (B) to the back of the monitor and secure it with screws (M-B) or (M-D) using both washers (M-E) and washers (M-F). Avoid excessive tightening of the screws to prevent damage to the monitor.

Slide the monitor onto the head of the swivel arm and install the security nut (K). Make sure the security nut is installed before you rotate the monitor.

Adjust the gas spring tension by turning the screw with the 6mm Allen wrench (P). Be sure to keep the arm in a horizontal position during adjustment, otherwise, it would be difficult to adjust the mount or damage the mount.

Turn Clockwise (” – ” direction) to reduce tension if the monitor lifts itself up.

Turn Counter-Clockwise (” + ” direction) to increase tension if the monitor falls down.

The tension should be just enough to hold your monitor in place without lifting itself up.

If needed, adjust the bolt on the side of the hinge behind the VESA plate to tighten or loosen the tilt angle support.

For both the bottom and upper portions of the spring arm, slide the cable cover up and away from the spring arm. You do not need to take much effort to pull the ends of the cable cover away.

On the bottom portion of the spring arm, insert the cable and slide the cable cover down.

On the upper portion of the spring arm, press the tabs on the inside of the cable cover slightly inward and slide down to reattach the cable cover.