Free English ELECTROLUX EFE4227 (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ELECTROLUX EFE4227 (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What safety warnings should be followed when installing the ELECTROLUX EFE4227 handle?
When handling and installing the accessory for the ELECTROLUX EFE4227, please observe the following safety points:
This accessory is not intended for use by persons, including children, with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.
The accessory may contain small parts that are a choking hazard and is not suitable for children under 3 years of age.
Do not use or place the accessory near the edge of a table or counter, or near a hot gas stove, electric burner, or heated oven.
This accessory is designed for indoor domestic use only.
Where are the handle bar and handle kit located in the ELECTROLUX EFE4227 packaging?
The components required for the ELECTROLUX EFE4227 are located in specific areas of the packaging:
The bar handle is securely packed in the rear left hand EPS corner post packing of the appliance.
The handle kit is located in the bottom of the refrigerator crisper or freezer drawer.
What items are included in the ELECTROLUX EFE4227 handle kit (ANC A03621901)?
The handle kit for the ELECTROLUX EFE4227 contains the following components:
| Component Item | Quantity | Part Number (ANC) |
|---|---|---|
| Handle bar (located in rear left hand corner eps packaging) | 1 | 811583305 |
| 3mm Allen key | 1 | A03207301 |
| Screw M4 | 3 | A03207202 |
| Pedestal (Top) | 1 | 1459143 |
| Pedestal (Center) | 1 | 1459147 |
| Pedestal (Bottom) | 1 | 1459145 |
How do I perform the bar handle assembly for the ELECTROLUX EFE4227?
To assemble the bar handle for the ELECTROLUX EFE4227, follow these steps:
Step 1. Using a suitable work space, place the handle bar with the screw holes facing up on a soft surface to prevent damage to the handle.
Step 2. Locate and position the three handle pedestals on the handle bar so that the pins locate in the holes and the screw holes align. Note that the pedestals are identified as top, bottom, and centre to aid assembly.
Step 3. Using the provided 3mm Allen key, assemble the handle brackets to the handle bar using the M4 screws provided.
Step 4. Ensure all screws are tightened securely.
What are the steps to assemble the bar handle to the ELECTROLUX EFE4227 door?
After the bar handle is assembled, attach it to the ELECTROLUX EFE4227 door using these steps:
Step 1. Position the top door handle over the handle mounts and align it with the template located on the door.
Step 2. Pull the handle down until it locks into position and aligns with the template on the door.
Step 3. Remove the templates from the door once the handle fitment is complete.
How should the ELECTROLUX EFE4227 handle be cleaned and maintained?
To clean the ELECTROLUX EFE4227 handle accessory safely, use only a soft cloth with unscented mild soap and lukewarm water.
Never use the following products as they may damage the accessory: hot water, solvents, commercial kitchen cleaners, aerosol cleaners, metal polishes, caustic or abrasive cleaners, or scourers. Many commercially available cleaning products and detergents contain solvents that can cause damage.
CLICK HERE TO DOWNLOAD ELECTROLUX EFE4227 (02) PDF DOCUMENT