Click here to download ELECTROLUX ECVI4262AS (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** EN ECV14262AS @Electrolux User Manual Range Hood electrolux.comregister 2

****** Page 2 ****** Welcome to Electrolux! Thank you for choosing our appliance. For Customer Care support and webshop visit: electrolux.com/support/ For extended version of User Manual visit: electrolux.com/manuals/ CONTENTS 1. SAFETY INSTRUCTION 2. ELECTRICAL REQUIREMENTS 3. PARTS SUPPLIE 4. OPTIONAL ACCESSORIES 5. INSTALLING THE HOOD 6. OPERATION 7. SPECIAL FUNCTION 8. CLEANING AND MAINTENANCE 9. TECHNICAL DATA IO.TROUBLE SHOOTING 1 1 .ENVIRONMENTAL PROTECTION 12.WARRANTY INFORMATION SAFETY INSTRUCTIONS Subject to change without notice. 2 5 6 6 7 14 14 15 16 16 16 17 Do not attempt to install or operate this appliance until you have read the safety instructions in this manual. Safety items throughout this manual are labelled with a Danger, Warning, or Caution based on the risk type. DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER: DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. 2 ENGLISH

****** Page 3 ****** CAUTION • CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. CHILD SAFETY Packing materials: • Packing cartons covered with rugs, bedspreads,plastic sheets, or stretch wrap may become airtight chambers and can quickly cause suffocation. • Removetheprotectivefilm coveringtheappliance before putting it into operation. • Destroy or recycle the appliance’s carton, plastic bags, and any other exterior wrapping material immediately after the product is unpacked. Children should never play with these items. Danger of suffocation! IMPORTANT CAREFULLY BEFORE INSTALLATION AND USE. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these instructions with this appliance for the owner. OWNER: Please retain these instructions for future reference. DANGER: Always switch off the electricity supply at the mains during installation and maintenance. WARNING: To reduce the risk of fire, electric shock, or injury to persons, observe the following: • FOR RESIDENTIAL USE ONLY • Use this appliance only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. • Installation work and electrical wiring must be done by qualified person(s )in accordance With all applicable codes & standards, including fire-rated construction. • Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back-drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. • When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities (e.g. gas pipes). • Ducted systems must always be vented to the outdoors. always be vented to the outdoors. 3 ENGLISH

****** Page 4 ****** WARNING: • Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,to the service panel. CAUTION: For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials or vapors. CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct air outside – do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages. WARNING: To reduce the risk of fire, use only metal duct work. Install this hood in accordance with all requirements specified. WARNING: To reduce the risk of fire or electric shock, do not use this hood with any external solid state speed control device. WARNING: To reduce the risk of a cooker top grease fire: • Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Always turn hood on when cooking over high heat WARNING: • Do not use the range hood without the grease filters, or if the filters are excessively greasy. • Use proper pan size. Always use cookware appropriate for the size of the surface element. 4 ENGLISH

****** Page 5 ****** WARNING: To reduce the risk of injury to persons, in the event of a cooker top grease fire, observe the following: • Smother flames with a close-fitting lid,cookie sheet, or other metal tray, then turn off the gas burner or the electric element. Be careful to prevent burns. If the flames do not go out immediately, evacuate and call the fire department. • Never pick up a flaming pan – you may be burned. • Do not use water, including wet dishcloths or towels – a violent steam explosion will result. • Use an extinguisher only if: You know you have a class ABC extinguisher, and you already know how to operate it. The fire is small and contained in the area where it started. The fire department is being called. You can fight the fire with your back to an exit. CAUTION: Always leave safety grills and filters in place. ELECTRICAL REQUIREMENTS IMPORTANT • Observe all governing codes and ordinances. CAUTION: To Reduce The Risk Of Fire And Electric Shock, Install This Rangehood Only With Integral Blowers Manufactured by Chinabest Home Appliance Co. , Ltd. Model CTH03-128D. It is the customer’s responsibility: • to contact a qualified electrical installer. • to assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 – latest edition* yor CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 -latest edition* * and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determines that the ground path is adequate. • Do not ground toa gas pipe. • Check with a qualified electrician if you are not sure range hood is properly grounded. • Do not have a fuse in the neutral or ground circuit. IMPORTANT Save installation instructions for electrical inspector’s use. The range hcni must be with copper wire only. The range should be directly to the fused disconnect (or circuit breaker) box through metal electriæl conduit. Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 – latest edition”, or CSA Standards C22.1- 94, Canadian Electrical Code Part 1 and C22.2 No.0-M91 – latest edition* * and all local codes and ordinances. A U. L.- or C.S.A.-listed conduit connector must be provided at each end of the power supply conduit (at the range hood and at the junction box). Copies of the standards listed may be obtained from: * National Fire Protection Association Battery marct’l Park Quincy, Massachusetts 02269 * * CSA Intemational 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575 Power requirement: 120V-, 60Hz, 15 or 20A branch circuit. 5 ENGLISH

****** Page 6 ****** PARTS SUPPLIED No. 2. 3. 4. 5. 6. 7. part Qty. 3.1 3.2 3 4 5 part Truss part Upper chimney Lower chimney Wire cover Wire cap Long screws ST6x70 Short screw M4x10 No. 9. 10. 11. 12. 13. 2. Assembly template Side supporting bracket Front and back supporting bracket Side sponge strip Front and back sponge strip 8′ extension chimney aux PN:EH108X62AS 12 extension chimney aux PN•.EH112X62AS 14′ extension chimney aux PN:EH114X62AS Qty. 2 2 2 2 1 OPTIONAL ACCESSORIES Recirculation kit with screws Elux PN: EHRKT62AS oo 6 ENGLISH

****** Page 7 ****** INSTALLING THE HOOD Tools/Materials required Duct tape Wire nuts Tape to mount template 6″ rounded metal duct, length to suit installation Measuring tape Pliers Gloves to protect against sharp edges Knife Safety glasses -e Electric drill Strain relief Spirit level -P Phillips (Pozidrive) # 2 screwdriver + torx # 2 Wire cutter/stripper Masking tape Hammer Saw, jig saw or reciprocating saw IMPORTANT We recommend that three people carry out the installation. Preparation • The vent hood should be on site before final framing and wall finishing. This will help to accurately locate the duct work and electrical service. • Installation will be easier if the vent hood is installed before the cooktop and countertop are installed. Ductwork and wiring locations: • Determine the exact location of the vent hood. • Plan the route for venting exhaust to the outdoors. Use the shortest and straightest duct route possible.For satisfactory performance duct run should not exceed 100′ equivalent length for any duct configurations. • Refer to ” Ductwork installation guidelines” chart to compute the maximum permissible length for duct runs to the outdoors (fig.O ). Fig.O Ceiling height Installation Center line height 30″ 36″ Ducting installation guidelines For safety reasons when ducting outdoors (not using a recirculation kit),ducting must vent directly outdoors (not into an attic, underneath the house, into the garage or into any enclosed space). Keep duct runs as short and straight as possible. Duct fittings (elbows and transitions) reduce air flow efficiency. Back to back elbow and “S” turns give very poor delivery and are not recommended. Use a suitable 6″ round duct. Flexible metal round ducts should only be used when no other duct fitting exists. limit use to short lengths and do not crush when making corners. 7 ENGLISH

****** Page 8 ****** Removing the packaging CAUTION IMPORTANT Remove the carton carefully. Framing must be capable of supporting Wear gloves to protect against sharp edges. WARNING Remove the protective film covering the product before putting into operation. Ceiling Support Structures • This vent hood is heavy. Adequate structure and support must be provided in all types of installations. Framing must support minimum 150 lbs load. • At the hood location, adequate bracing is required to support the weight of the hood (fig. • Arrange cross framing in the ceiling to suit —6″ duct 150 lbs. Figo EXAMPLE A 10 Install cross-framing symmetrically over duct/cooktop centerline Alig duct to center Front of cooktop Of hood the existing structure (fig.O ) • Your ceiling joists will be like one of the following examples. Top view-ceiling joists parallel to front of hood EXAMPLE B 6″ jois spacing Fig.@ 10 1116″ 14 27132″ Front 10 Install cross-framing — syrmnetrica+ly-ove duct/cooktop centerline Align duct to center Front of cooktop of hood Top view-ceiling joists run perpendicular to front of hood EXAMPLE C 10 1116″ Install cross-framing symmetrically over duct/cooktop centerline 16″ joist spacing Front of hood G” duct— Align duct to center of cooktop Cooktop outline Cooktop outline Cooktop outline NOTE: Do not cut the duct opening shown on the template for the recirculating installation. 8 ENGLISH TOP view—ceiling joists at angle to front Of hood

****** Page 9 ****** Examples of possible ducting or air recirculation Fig.@ Roof pitch with flashing and cap Pipe Collar Recirculation kit shown Pipe Collar IMPORTANT This range hood is very heavy. Adequate structure and support must be provided in all types of installations. Step 1 • Make sure that no cables or pipes will become damaged (e.g. electric, gas, water; test the areas in question with a cable detector). • Using the template, mark and drill 4 holes into the ceiling. Measure as displayed in diagram (fig.@).The holes must be drilled into a wood structure capable to support 1501bs load. Fig.O o o-L NOTE 1 .The center of the template must match the center of the cooktop and the edges must be parallel to the sides of the cooktop. 2. Have a suitable ladder ready so that you can easily reach up to the ceiling. step 2 Unscrew 16 screws between the two sections of the structure. Adjust extension of the hood support structure (dimenssion A), as the final height of the hood depends on this ,and remember that with installation completed to the hood must be at least 30″ above the cooktop. Fig.O Top Of upper brack Dimension A Top of lower brack * 1 With 81/12/14′ extension chimney kit— not supplied. Please call Electrolux at 1-800-944-9044 (USA) or 1-800-265- 8352 (Canada) to order this kit. * 2 ” Dimension A” represents the height from the top of upper bracket to the top of lower bracket (fig.O ). step 3 Fix the two sections of the structure using 16 screws. NOTE It is recommended to fix the supplied 4 supporting brackets (1 0, 11 ) with sponge strips(1 2, 13)onto the lower brackets to make sure two flue covers fit closely(fig.@). 9 ENGLISH

****** Page 10 ****** Fig.o Step 4 Mount the truss part (2) onto the ceiling with 4 sets of long screws (6) and washers (8) (fig.@). • Make sure the power cable for the range hood is routed inside the bracket. Fig 8 10 ENGLISH Fig.@ IMPORTANT Before mounting the truss part onto the ceiling, please remove the supporting plate firstly (fig.@). Remember to keep these screws which will be reused in step 8 Step 5 Depending on the ceiling height ensure required power cable length. See the table (fig@) below for reference. Ceiling height Power cable length Figo 8 feet 10 feet 3 feet 5feet Power cord 12 feet 7 feet 14 feet 9 feet

****** Page 11 ****** • Loosen the 4 short screws from the junction box (fig.O) Figo • Connect the incoming positive, neutral and ground cables to the respective terminals. (fig.@). Fig. @ L (live) = Black N (neutral) = White C (ground) = Green • Mount the junction box onto the range hood using 4 short screws (fig.@). Fig. O Step 6 Place the exhaust duct onto the outlet and secure it with duct tape (not provided) (fig.@) Fig. O step 7 Insert the top chimney into the truss (fig.@), secure it with two screws(7). Insert the bottom chimney in its seat so that it completely covers the motor compartment and electrical connection box(fig.@). Fig.O Fig.o CAUTION Danger of injury. The chimney skirts may have some sharp edges. 11 ENGLISH

****** Page 12 ****** Step 8 Hook the hood body onto the truss, ensuring it fits properly, secure the body to the truss with 12 screws (7) then tighten IMPORTANT Make sure the wire terminal passes though the hole on the air house (fig.@) Fig.O IMPORTANT Before hooking the hood onto the truss, please make sure the aspiration plate and filter have been removed from the body to avoid it fall and injury to installer. Step 9 Connect as shown the wire terminal and the controller terminal(fig.@ Ensure the wire supplied cover secure firmly with three screws (7)(fig.@). Figo The hole on the air house 12 ENGLISH Fig. O step 10 Install the aspiration plate to the hood body. • Fit the right bracket on the aspiration plate to the right fixed hinge(fig.@),then push the left hinge to the end to match the hole of the left bracket on the plate and release the hinge to lock them(fig.@). Fig.@ Fig .o

****** Page 13 ****** Exhaust operation Makeup Air Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. Air recirculation operation Recirculated air: Kitchen fumes are removed and after purification are fed back into the room through the upper ventilation openings. The purification takes place via metallic anti-grease filter. No wall breakthrough is required for recirculated air operation. Installing range hood to the wall in recirculation mode • For operation of the range hood with recirculation, recirculation kit #EHRKT62AS is needed and can be purchased by calling 1-800-944-9044 (USA) or 1-800-265-8352 • (Canada) Follow steps 1 t04 from Installing range hood to the wall(Exhaust operation) chapter. • Fix the recirculation plate to mounting plate with 4 supplied short screws(fig.@ ).Fix the recirculation box with 8 supplied short screws(fig.@ ). Install charcoal filter to each side of the blower motor by inserting the filters onto the “T” shaped stud and twisting to lock them into place. Reinstall the grease filter close aspiration plate.(fig.@ ) Fig.@ Fig.@ Fig.@ “i’ili/i ,nin 13 ENGLISH

****** Page 14 ****** OPERATION Press one of the speed Yl/Y2/Y3 button to turn the appliance on. Button Function Press button O to switch the appliance off. Press button for low speed. Press button Y2 for medium speed. Press button Y, for high speed. Press button -A-to set the light to a low intensity. Press the second time to set the light to a medium intensity. Press the third time to set the light to a high intensity. Press the fourth time to turn the light off. For best performance SPECIAL FUNCTION Heat sensor This product is equipped with a heat sensor that will automatically turn the vent fan ON at medium speed when high temperatures are detected (over 1580F or 700C). Ifthe vent fan is already running at low speed and high temperatures are detected, the vent fan will automatically change to medium speed 14 ENGLISH NOTE It is recommended to use the range hood while cooking and for several minutes after cooking to reduce humidity and odors inside your kitchen space. Turn on the range hood before starting to cook. Clean the filters frequently (refer to Cleaning and maintenance below). Use low speed for normal use and higher speed for strong odors or fumes. During this event, the vent fan speed can be changed manually to high speed, but not low speed or off. • When the heat sensor detects a significant drop in temperature, then the appliance will operate normally

****** Page 15 ****** CLEANING AND MAINTENANCE Cleaning DANGER Always switch off the electricity supply at the breaker box during installation, cleaning, or maintenance. NOTE The efficiency of the range hood depends on the cleanliness of the intake and filters. Grease should not be allowed to accumulate on hood or filter. • Clean the appliance in the following intervals: c Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the appliance. Aluminum filter: The filter collects grease, smoke and dust so the filter is directly affecting the efficiency of the range hood. If not cleaned, the grease residue(potential flammable) will saturate on the filter. Clean it with household cleaning detergent. The filter is dishwasher safe. Recirculation box: clean the ventilation openings on the top sides. Charcoal filters: If the model is not vented to the outside, the air will be recirculated through disposable charcoal filters that help remove smoke and odors. The charcoal filters cannot be cleaned, they must be replaced regularly (depending on range hood usage). Note: Do not rinse or put charcoal filters in a dishwasher. Note: Charcoal filters are not included with the range hood. a IMPORTANT Clean the filter every month to prevent risk of fire. Maintenance • User service-Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. IMPORTANT Parts and accessories not provided with your hood, or for replacement, can be purchased at electrolux.com or by calling 1-800-944-9044 (USA) or 1-800-265-8352 (Canada). 15 ENGLISH

****** Page 16 ****** TECHNICAL DATA Power supply: 120V-60HZ Motor Power: 330W Lamp power: 24W for ECV14262AS TROUBLESHOOTING Problem Excessive vibration Light on, but fan does not work. Cause The appliance in not fixed properly on the brackets. The fan blade is damaged. The fan motor is not fixed tightly. The fan blade is jammed. The motor is damaged. Light bulb broken. Both light and fan do not work Problem with electrical connection. Distance between the appliance and the cooking place too large. Suction performance is not Metallic anti-grease filter is good. dirty. Charcoal filter is dirty Solution Take down the appliance and check it is properly fixed. Switch off the appliance. Repair to be carried out by qualified service personnel only. Replace with a bulb with correct rating. Check the electrical connection with an electrician. Readjust the distance(Page 7, fig.6and table below) Clean filters(see Cleaning and maintenance). Charcoal filter(see Cleaning and maintenance) Environmental protection Waste electrical products should not be disposed of with household waste. Please recycle where 16 ENGLISH facilities exist. Check with your local Authority or retailer for recycling advice.

****** Page 17 ****** WARRANTY INFORMATION Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been removed, altered or cannot be readily determined. 2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada. 3. Rust on the interior or exterior of the unit. 4. Products purchased “as-is” are not covered by this warranty. 5. Products used in a commercial setting. 6. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions. 7. Service calls to correct the installation of your appliance or to instruct you how to use your appliance. 8. Expenses for making the appliance accessible for servicing, such as removal of trim,cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory. 9. Service calls to repair or replace consumable parts like grease or charcoal filters. 10.Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. 11 .Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc. 12.Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God. DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMERS SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. 17 ENGLISH

****** Page 18 ****** If You Need Service Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below. This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice. USA 1-877-435-3287 Electrolux Major Appliances North America 10200 David Taylor Drive Charlotte, NC 28262 Canada 1-800-265-8352 Electrolux Canada Corp. 5855 Terry Fox way Mississauga, Ontario, Canada L5V 3E4 18 ENGLISH

****** Page 19 ****** electrolux.com

****** Page 20 ****** 0 099 •u! V9/t9 01 ff8LZ Cu! 91/1 L)V6L L

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELECTROLUX ECVI4262AS (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.