ELECTRIQ EIQ25CMMW (01) PDF Document

When installing the ELECTRIQ EIQ25CMMW, follow these placement guidelines:

Ensure a gap of at least 20cm is maintained from the top surface of the microwave to any ceiling or cabinet.

The microwave is intended for freestanding use only and must not be placed inside a cabinet.

Maintain 5cm of space at all sides for proper ventilation. Do not block or cover any openings on the unit.

Place the microwave on a flat surface capable of supporting its weight and the weight of any contents.

To aid in the insertion and removal of food, do not install the appliance lower than 85cm from the ground.

Place the unit at least 5cm from the edge of a counter or table to prevent accidental falling.

Do not install the ELECTRIQ EIQ25CMMW above a heat source or another cooking appliance.

Ensure the feet of the microwave are not removed.

Before using the ELECTRIQ EIQ25CMMW for the first time, perform the following steps:

1. Remove all packaging materials and protective films from the appliance.

2. Unpack the microwave and check for any damage. If any parts are damaged, do not plug the unit in.

3. Remove all accessories and clean them using a soft cloth and a mild soapy water solution.

4. Clean the interior cavity and the exterior of the appliance with the same solution and a cloth.

5. Leave the door open with the appliance off to allow it to dry completely.

6. Plug the microwave into a suitable, grounded socket.

The ELECTRIQ EIQ25CMMW features five power levels as detailed in the following table:

To select a power level, repeatedly press the POWER button to cycle through the options.

To set the timer on the ELECTRIQ EIQ25CMMW, enter the desired duration using the numbered buttons on the control panel. The maximum time that can be entered is 99 minutes and 99 seconds (99:99). For example, to set the timer for 15 minutes, enter 15:00. Once the time is set, click the START button to begin the selected function.

The Express Cooking function on the ELECTRIQ EIQ25CMMW operates at 100% power and is available for durations up to 9 minutes. While in standby mode, press a number on the control panel corresponding to the number of minutes you wish to cook (e.g., press 5 for 5 minutes). Then, press START to begin.

Alternatively, you can repeatedly press the START button while in standby or during cooking to increase the time in 30-second increments.

The STOP button on the ELECTRIQ EIQ25CMMW serves multiple purposes:

When selecting a function or setting a time, press STOP once to clear the current selection.

While cooking is in progress, press STOP once to pause the operation. Pressing it a second time will cancel the function entirely.

You can also pause cooking by simply opening the door. To resume, close the door and press the START button.

To use the defrost function on the ELECTRIQ EIQ25CMMW, press the DEFROST button. This automatically selects 20% power (displayed as P20 for 3 seconds). After the power level is displayed, enter the desired defrosting time using the 0-9 buttons. Press START to begin. An alarm will sound when the process is finished. The maximum time for defrosting is 99:99.

To lock the control panel of the ELECTRIQ EIQ25CMMW and make all buttons inoperable, press and hold the STOP button for 3 seconds. To unlock the panel, press and hold the STOP button again for 3 seconds.

The ELECTRIQ EIQ25CMMW uses specific display prompts to guide operation:

DOOR: When the unit is in standby and the door is closed, or immediately after cooking ends, the display shows “DOOR” to prompt you to open the door. Open the door within 1 minute to clear this display.

Err: If the START button is pressed but there is nothing inside the cooking cavity, the infrared sensor will detect this, display “Err”, and sound an alarm. Press STOP to cancel or open the door and add food.

END: When a cooking cycle finishes naturally, the display will show “END” and sound a tone. Open the door or press any button to clear the display.

To ensure a container is safe for use in the ELECTRIQ EIQ25CMMW, perform this test:

1. Fill a known microwave-safe container with 1 cup (250ml) of cold water.

2. Place the microwave-safe container and the utensil being tested into the microwave.

3. Heat on maximum power for exactly 1 minute. Do not exceed this time.

4. Carefully feel the utensil. If the utensil itself is warm, it is not suitable for microwave cooking and should not be used.

The following materials can be used in the ELECTRIQ EIQ25CMMW:

Avoid using the following materials in the ELECTRIQ EIQ25CMMW to prevent arcing, fire, or damage:

Follow these instructions for cleaning the ELECTRIQ EIQ25CMMW:

Always disconnect the appliance from the power supply before cleaning.

Clean the front, interior cavity, steel parts, door seal, and accessories using a warm, mildly soapy solution. Dry thoroughly with a soft, dry cloth.

Do not use glass cleaners, abrasives, or scrapers on these sections.

The glass window can be cleaned with glass cleaner. Do not spray it directly onto the glass; spray a damp cloth first and then wipe.

Ensure the door lock is kept free of food debris to prevent malfunctions.

Never use corrosive chemicals, vapors, metal scourers, or steam cleaners on the appliance.

The appliance should never be submerged in water, sprayed, or cleaned with a water jet.

For effortless cleaning of food residue from the cavity walls of the ELECTRIQ EIQ25CMMW, place half a lemon in a bowl with 300ml (1/2 pint) of water. Heat the bowl on 100% microwave power for 10 minutes. After heating, wipe the interior walls clean using a soft, dry cloth.

The following occurrences are normal during the operation of the ELECTRIQ EIQ25CMMW:

Interference: Radio and TV reception may be interfered with while the microwave is running, similar to other small appliances.

Dim Light: The oven light may become dim during low-power cooking modes.

Steam/Hot Air: Cooking food releases steam. While most exits through the vents, some may accumulate on the door or in cold spots.

If the ELECTRIQ EIQ25CMMW is not working correctly, consult this troubleshooting table: